Table of Contents
Advertisement
12 IN. (305 MM)
COMPOUND MITER SAW
SIERRA INGLETEADORA COMPUESTA
DE 305MM (12 PULG.)
Instruction Manual
Manual de instrucciones
Español: Página 32
www.portercable.com
INSTRUCTIVO DE OPERACIÓN, CENTROS DE
SERVICIO Y PÓLIZA DE GARANTÍA.
CATALOG NUMBER
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
PXMS12ISB
1
Advertisement
Table of Contents
Related Manuals for Porter-Cable PXMS12ISB
Summary of Contents for Porter-Cable PXMS12ISB
- Page 1 COMPOUND MITER SAW SIERRA INGLETEADORA COMPUESTA DE 305MM (12 PULG.) Instruction Manual Manual de instrucciones Español: Página 32 www.portercable.com INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. CATALOG NUMBER ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. PXMS12ISB...
- Page 2 TABLE OF CONTENTS SECTION PAGE PRODUCT SPECIFICATIONS........................CALIFORNIA PROPOSITION 65......................... SAFETY GUIDELINES - DEFINITIONS ...................... POWER TOOL SAFETY..........................MITER SAW SAFETY..........................ELECTRICAL REQUIREMENTS AND SAFETY..................TOOLS NEEDED FOR ASSEMBLY......................CARTON CONTENTS..........................KNOW YOUR COMPOUND MITER SAW....................GLOSSARY OF TERMS..........................ASSEMBLY AND ADJUSTMENTS......................OPERATION..............................
- Page 3 CALIFORNIA PROPOSITION 65 WARNING WARNING SAFETY GUIDELINES - DEFINITIONS WARNING ICONS SAFETY ALERT: Precautions that involve your safety. PROHIBITION DOUBLE INSULATED CONSTRUCTION WEAR EYE PROTECTION: Always wear safety goggles or safety glasses with side shields. WEAR RESPIRATORY AND HEARING PROTECTION: Always wear respiratory and hearing protection. READ AND UNDERSTAND INSTRUCTION MANUAL: To reduce the risk of injury, user and all bystanders must read and understand instruction manual before using this product.
- Page 4 POWER TOOL SAFETY ALWAYS WEAR EYE PROTECTION. Any GENERAL SAFETY INSTRUCTIONS power tool can throw foreign objects into the BEFORE USING THIS POWER TOOL eyes and could cause permanent eye damage. Safety is a combination of common sense, staying alert ALWAYS wear Safety Goggles (not glasses) and knowing how to use your power tool.
- Page 5 POWER TOOL SAFETY 24. DO NOT operate the tool if you are under the WEAR HEARING PROTECTION. to reduce influence of any drugs, alcohol or medicationn that the risk of induced hearing loss. could affect your ability to use the tool properly. 25.
- Page 6 MITER SAW SAFETY SPECIFIC SAFETY INSTRUCTIONS FOR THIS 18. MAKE SURE the blade is not contacting the workpiece COMPOUND MITER SAW before the switch in turned ON. 1. DO NOT USE THIN KERF BLADES they can deflect 19. IMPORTANT: After completing the cut, release the and contact guard an can cause possible injury to the trigger and wait for the blade to stop before returning operator.
- Page 7 MITER SAW SAFETY 33. To avoid loss of control or placing hands in the path 39. WARNING: For your own safety, read instruction of the blade, hold or clamp all material securely against manual before operating miter saw. Failure to obey the fence when cutting.
- Page 8 ELECTRICAL REQUIREMENTS AND SAFETY POWER SUPPLY AND MOTOR SPECIFICATIONS 1. Connect this saw to a 120 V circuit. This circuit must The AC motor used in this saw is a universal, nonreversible not be less than a #12 wire with a 20 A time lag fuse type.
- Page 9 ELECTRICAL REQUIREMENTS AND SAFETY MINIMUM GAUGE FOR EXTENSION CORDS (AWG) (When using 120 volts only) More Than Not More Than 25ft. 50ft. 100ft. 150ft. Not Recommended...
- Page 10 TOOLS NEEDED FOR ASSEMBLY CARTON CONTENTS CHECKING CONTENTS Check the contents of your miter saw carton to make sure that you have received all parts. In addition to this Flat bladed Blade wrench instruction manual, the carton should contain: screwdriver (screwdriver+ WARNING 6 mm hex key)
- Page 11 KNOW YOUR MITER SAW Carry handle Upper blade guard Motor Dust port Self-retracting lower blade guard Head lock knob Guide fence Base Miter scale Wrench storage Locking button Miter lock handle (extend the angle of Miter detent inclination by +/- 3°) Miter table Hand hold Switch handle...
- Page 12 GLOSSARY OF TERMS COMPOUND MITER SAW TERMS Made of shock-resistant, see-through plastic that provides Supports the table, holds accessories and allows protection from each side of the blade. It retracts over for workbench or leg set mounting. the upper blade guard as the saw is lowered into the workpiece.
- Page 13 GLOSSARY OF TERMS A sticky sap that has hardened. Any cutting operation where the blade extends completely through the thickness of the The number of workpiece. turns completed by a spinning object in one minute. The item being cut. The surfaces of a The area of the workpiece or table workpiece are commonly referred to as faces, ends and top directly in line with the travel of the blade or the part...
- Page 14 ASSEMBLY AND ADJUSTMENTS WARNING To reduce the risk of injury, turn unit off and disconnect An accidental start-up can cause injury. Estimated Assembly Time: 2 Minutes ASSEMBLY INSTRUCTIONS WARNING To avoid injury, do not connect this miter saw to a power 4.
- Page 15 Fig. E IMPORTANT: Fig. F WARNING Fig. G TRANSPORTING THE SAW (Fig. F-G) INSTALL THE DUST BAG (FIG. H) WARNING NOTE: WARNING WARNING...
- Page 16 Fig. H Fig. I INSTALL THE MATERIAL CLAMP ASSEMBLY (FIG. J) NOTE: WARNING REMOVE AND INSTALL THE TABLE INSERT (FIG. I) CAUTION WARNING To install the material clamp: Fig. J...
- Page 17 Fig. M REMOVE AND INSTALL THE BLADE (FIG. K-N) WARNING REMOVE BLADE (FIG. K-N) NOTE: Fig. K NOTE: Fig. N NOTE: Fig. L NOTE: WARNING...
- Page 18 INSTALLING BLADE (FIG. L-N) NOTE: MOUNTING INSTRUCTIONS For stationary use, NOTE: Fig. O WARNING Fig. P Stationary use MOUNTING THE MITER SAW (FIG. O-Q) WARNING NOTE:...
- Page 19 Fig. R NOTE: For portable use, Fig. Q Fig. S CAUTION WARNING ADJUSTMENT INSTRUCTIONS 90° (0°) BEVEL POINTER ADJUSTMENT (Fig. T) BEVEL STOP ADJUSTMENT (Fig. R-V) WARNING Fig. T 90° (0°) BEVEL ADJUSTMENT (Fig. R-S) NOTE:...
- Page 20 45° BEVEL ADJUSTMENT (Fig. U-V) NOTE: CAUTION NOTE: Fig. U Fig. W Fig. X Fig. V MITER ANGLE POINTER ADJUSTMENT (Fig. Y) Fig. Y ADJUSTING FENCE SQUARENESS (Fig. W-X)
- Page 21 SAFETY INSTRUCTIONS FOR BASIC SAW OPERATION BEFORE USING THE MITER SAW WARNING To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. Keep all guards in place, in working order and properly adjusted.
- Page 22 USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECES WARNING DRESS FOR SAFETY WHEN SAW IS RUNNING WARNING Do not allow familiarity from frequent use of your miter saw to result in a careless mistake. A careless fraction of a second is enough to cause a severe INSPECT YOUR WORKPIECE injury.
- Page 23 OPERATION Fig. AA Before freeing jammed material: Fig. Z WARNING To avoid injury, after completing a cut and releasing the trigger switch, allow the blade brake to activate and stop the blade before raising the cutting head. WARNING To avoid injury, check and tighten the arbor bolt periodically.
- Page 24 OPERATION Fig. BB Fig. DD COMPOUND CUT (Fig. EE) BEVEL CUT (Fig. CC-DD) Fig. EE WARNING Fig. CC CUTTING BOWED MATERIAL (Fig. FF)
- Page 25 OPERATION Fig. FF CUTTING CROWN MOLDING (Fig. HH) WARNING Correct Incorrect CUTTING BASE MOLDING (Fig. GG) Fig. HH Fig. GG Miter saw table BEVEL/MITER SETTINGS (Fig. II) Fig. II Miter saw table Miter saw table NOTE: NOTE:...
- Page 26 OPERATION Bevel/Miter Settings BEVEL MITER TYPE OF CUT SETTING SETTING Inside corner-Left side Inside corner-Right side Outside corner-Left side Outside corner-Right side...
- Page 27 GENERAL MAINTENANCE Fig. JJ WARNING To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. DANGER LOWER BLADE GUARD WARNING WARNING REPLACING CARBON BRUSHES (Fig. JJ) EMPTYING SAWDUST BAG WARNING WARNING...
- Page 28 WARNING MOTOR PROBLEM PROBLEM CAUSE PROBLEM CAUSE SAW OPERATION PROBLEM PROBLEM CAUSE PROBLEM CAUSE...
- Page 29 RECOMMENDED ACCESSORIES ACCESSORIES WARNING Use only accessories recommended for this miter saw. Follow instructions that accompany accessories. Use of improper accessories may cause hazards. The use of any cutting tool except 12 in. (305 mm) saw blades which meet the requirements under recommended accessories is prohibited.
- Page 30 PART PART# PART PART# Description Description Fig. KK...
- Page 31 1 YEAR WARRANTY REPLACEMENT PARTS 1 YEAR WARRANTY REPLACEMENT PARTS: 90 DAY MONEY BACK GUARANTEE:...