Sony ZS-M7 Service Manual

Sony ZS-M7 Service Manual

Personal minidisc system
Table of Contents

Advertisement

SERVICE MANUAL
Ver 1.2 2001.07
With SUPPLEMENT 1
(9-923-346-82)
Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation.
"DOLBY" and the double-D symbol a are trademarks of
Dolby Laboratories Licensing Corporation.
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
With 4-ohm loads, both channels driven from 100 – 10,000 Hz ; rated 7W
per channel-minimum RMS power, with no more
than 10% total harmonic distortion in AC operation (US Model).
CD player Section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 785 nm
Emission duration : Continuous
Laser output : Less than 44.6 W
(This output is the value measured at a distance of about 200
mm from the objective lens surface on the optical pick-up
block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of programme positions
2
Frequency response
20 – 20,000 Hz +1 /–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
US Model :
FM : 87.6 – 108 MHz
AM : 530 – 1,710 kHz
9-923-346-12
Sony Corporation
2001G0200-1
Personal Audio Company
Shinagawa Tec Service Manual Production Group
© 2001.7
Model Name Using Similar Mechanism
MD
MD Mechanism Type
Section
Optical Pick-up Type
Model Name Using Similar Mechanism
CD
MD Mechanism Type
Section
Optical Pick-up Type
SPECIFICATIONS
EXCEPT US Model :
FM : 87.6 – 107 MHz
MW : 531 – 1,602 kHz
LW : 153 – 279 kHz
IF
FM : 10.7 MHz
MW/LW : 450 kHz
Aerials
FM : Telescopic areal
Extension areal terminal
AM : Extension areal terminals (US Model)
MW/LW : Extension areal terminals (EXCEPT US Model)
MD player section
System
Minidisc digital audio system
Disc
MiniDisc
Laser diode properties
Material: GaAlAs
Wave length: 785 nm
Emission duration : Continuous
Laser output : Less than 44.6 W
(This output is the value measured at a distance of about 200
mm from the objective lens surface on the optical pick-up
block with 7 mm aperture.)
PERSONAL MINIDISC SYSTEM
ZS-M7
US Model
AEP Model
UK Model
Tourist Model
NEW
MDM-3EG
KMS-260A
NEW
CDM-2411AAA
DAX-11A
– Continued on page 2 –

Advertisement

Table of Contents
loading

Summary of Contents for Sony ZS-M7

  • Page 1 ZS-M7 SERVICE MANUAL US Model AEP Model Ver 1.2 2001.07 UK Model With SUPPLEMENT 1 (9-923-346-82) Tourist Model Dolby noise reduction manufactured under license from Model Name Using Similar Mechanism Dolby Laboratories Licensing Corporation. MD Mechanism Type MDM-3EG “DOLBY” and the double-D symbol a are trademarks of Section Dolby Laboratories Licensing Corporation.
  • Page 2: Table Of Contents

    Recording/Playback time Outputs Maximum 74 minutes (with MDW-74) Headphones jack (stereo minijack) (2) : For 32 ohms Revolutions impedance headphones 400 rpm to 900 rpm (CLV) Power outputs Error correction 7 W + 7 W Advanced Cross Interleave Reed Solomon Code (ACIRC) Power requirements Sampling frequency For personal minidisc system :...
  • Page 3: Service Note

    COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK !ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
  • Page 4 ABOUT THE BD BOARD WAVEFORM CHECKING JIG The special jig (J-2501-124-A) is highly convenient when check- ing the waveform of the BD board of the MD section. Pin names and items to check are as follows: I+3V : for IOP measurement (check for depleted optical pickup laser) IOP : for IOP measurement (check for depleted optical pickup laser)
  • Page 5: General

    SECTION 2 GENERAL – 5 –...
  • Page 6 – 6 –...
  • Page 7 This section is extracted from instruction manual. – 7 –...
  • Page 8 – 8 –...
  • Page 9 – 9 –...
  • Page 10 – 10 –...
  • Page 11 – 11 –...
  • Page 12 – 12 –...
  • Page 13 – 13 –...
  • Page 14 – 14 –...
  • Page 15 – 15 –...
  • Page 16 – 16 –...
  • Page 17 – 17 –...
  • Page 18 – 18 –...
  • Page 19 – 19 –...
  • Page 20 – 20 –...
  • Page 21: Disassembly

    SECTION 3 DISASSEMBLY The equipment can be removed using the following procedure. < MAIN BLOCK SECTION > Cabinet (Front) Left key board, Front key board, Top key board, Right board, Relay board ASSY Cabinet (Rear) FL board, Trans board, Tuner board, FM ANT board, AM ANT board ASSY MD chassis ASSY MD Block ASSY, Filter board...
  • Page 22: Left Key Board, Front Key Board, Top Key Board, Right Key Board, Relay Board

    3-2. LEFT KEY BOARD, FRONT KEY BOARD, TOP KEY BOARD, RIGHT KEY BOARD, RELAY BOARD 3 Screws (2.6X8) Front key board 5 Screws (2.6X8) 1 Screws ( 2.6X8) Button (MEGA BASS) Left key board Top key board 7 Screw (M1.7X5) !º...
  • Page 23: Tuner Board, Fm Ant Board, Am Ant Board

    3-4. TUNER BOARD, FM ANT BOARD, AM ANT BOARD Cabinet (Rear) ASSY EXCEPT US model 3 Screws (+BTP 3X12) FM ANT board 7 Screws (+BVTP 3X12) 5 Screws (+BVTP 3X12) !º Tuner board AM ANT board 1 Wire parallel (FFC) (13core) 9 Screws (+BVTP 3X12)
  • Page 24: Md Block Assy, Filter Board

    3-6. MD BLOCK ASSY, FILTER BOARD MD Block ASSY 3 Screws (M1.7X5) 2 CN703 (2 pin) 5 Wire, Parallel (FFC) (26 core) Filter board 1 Wire, Parallel (FFC) (26 core) 3 Screws 6 Screws (M1.7X5) MD chassis 3-7. AUDIO BOARD, HP BOARD, LINE IN BOARD 3 Screws Audio board (+BVTP 3X16)
  • Page 25: Main Board, Cd Block Assy

    3-8. MAIN BOARD, CD BLOCK ASSY 5 Screws (+BVTP 3X12) 3 Screws (2.6X8) Main board MD Chassis 1 CN701 Wire, Parallel (FFC)(21 core) (Main board) 2 CN803 (5pin) CD Block ASSY (Main board) < MD BLOCK SECTION > 3-9 . SHIELD CASE (TOP), SHIELD CASE (BOTTOM) 1 Screws (M1.7X2) Shield case (Top) 1 Screws (M1.7X2)
  • Page 26: Dg Board, Bd Board, Md Mechanism Deck

    3-10 . DG BOARD, BD BOARD, MD MECHANISM DECK 7 Step screw 7 Step screw Insulator Insulator MD mechanism deck When mounting, make sure that A Sub chassis ASSY sets in the correct position BD board 2 Wire, Parallel (FFC)(19core) 5 Screw (+BVTT 2X4) DG board...
  • Page 27: Sw Board

    3-12 . SW BOARD SW board 1 Claws 1 Claws 1 Claws MD mechanism deck 3-13. SLIDER ASSY, “ HEAD, OVER WRITE ” 2 Screw (M1.7X6) Head, Over write 1 Screw (M1.7X2) 6 Position the gear shaft Claw (L) as ahown in the diagram Retainer Slider ASSY Claw...
  • Page 28: Md Optical Pick-Up Block

    CAUTION DURING SLIDER ASSY ASSEMBLY Slider ASSY Mount the A of the lever (head up) so that it passes above the slider ASSY. Take caution as to not damage the detection switch 3-14. MD OPTICAL PICK-UP BLOCK MD Optical pick-up block Shaft (Main shaft) 1 Remove the lever –...
  • Page 29: Loading Board, "Tray Assy, Cd

    < CD BLOCK SECTION > 3-15. LOADING BOARD, “TRAY ASSY, CD” 5 Screws (+BVTP 3X10) 3 Screws (+BVTP 3X10) Plate (L), Side 1 Screws (+BVTP 3X10) Loading chassis Loading board Cover (L), Side Plate (R), Side Slider(L) 3 Screws Wier, Parallel (FFC)(21 coer) (+BVTP 3X10) (Main board CM701) Slider(R)
  • Page 30: Test Mode

    SECTION 4 TEST MODE 4-1. CAUTIONS WHEN USING THE TEST MODE 4-5. SELECTING THE TEST MODE 1 Check to make sure the inserted disk is completed stopped be- There are 9 types of test modes (see table below). Turning the AMS fore removing since loading related operations will operate re- dial clockwise switches modes shown in the table in the order from gardless of the Test mode operation.
  • Page 31: Functions Of Other Buttons

    4-5-2. Operating in the Continuous Recording mode 4-7. TEST MODE DISPLAY 1. Entering the Continuous Recording mode The display will switch in the following sequence every time the 1 Insert a disk that may be recorded into the unit (see Note 3) DISPLAY button is pressed.
  • Page 32: Adjustments

    SECTION 5 ADJUSTMENTS MD SECTION 5-3. CAUTIONS DURING ADJUSTMENT 1) After replacing the following parts, make adjustments and checks 5-1. CAUTION WHEN CHECKING LASER DIODE for the table items where indicated with a O in the order given. EMISSION Optical BD board Never look from directly above when checking the laser diode emis- pickup...
  • Page 33: Temperature Compensation Offset Adjustment

    5-5. TEMPERATURE COMPENSATION OFFSET 7. Next, turn the AMS dial until “ LDPWR CHECK ” is displayed. ADJUSTMENT 8. Press the ENTER/YES button once to display “ LD 0.9mW $ The temperature data at the time is saved in the non-volatile storage ”.
  • Page 34: Focus Bias Adjustment

    7. Press the ENTER/YES button to save the adjustment result to 17. Press the ENTER/YES button to save the adjustment result to the non-volatile storage memory (at this time “ EFB= SAVE the non-volatile storage memory (at this time “EFB= SAVE”...
  • Page 35: Error Rate Check

    5-9. ERROR RATE CHECK 5-11. ADJUSTMENT AND CONNECTION LOCA- 5-9-1. CD error rate check TIONS [BD BOARD] (Side A) Procedure: 1. Insert the check disk (MD) TDYS-1 CN110 2. Turn the AMS dial until “ CPLAY MODE ” is displayed. 3.
  • Page 36 CD SECTION 3. Traverse signal check Connection Point: 1. Enter the CD Test mode (see page 30) Oscilloscope Main board MD EF TG FB CN701 $∞ pin (TEO) TP(VC) 88 07 00 3A0 Press the FF or FR from 2. Check to see that the traverse signal level is between 400 The above is the default display.
  • Page 37 TUNER SECTION EXCEPT US model AM Section FM IF ADJUSTMENT Function switch : Adjust for a maximum reading on level meter. : US Model 10.7MHz MW (LW) : EXCEPT US Model Volume : MIN AM RF signal LW FREQUENCY COVERAGE ADJUSTMENT Put the lead-wire generator antenna close to...
  • Page 38 Adjustment Location : US Model [TUNER BOARD] (Side A) CFT1 : AM IF Adjustment IC 1 L1 : AM Tracking Adjustment L2 : AM Frequency Coverage Adjustment CT1 : AM Tracking Adjustment EXCEPT US Model [TUNER BOARD] (Side A) CFT1 : MW (LW) IF Adjustment L10 : FM IF Adjustment IC 1 L5 : LW Tracking Adjustment...
  • Page 39: Diagrams

    SECTION 6 DIAGRAMS 6-1. EXPLANATION OF IC TERMINALS BD BOARD IC101 MD SECTION RF AMPLIFIER (CXA2523R) Pin No. Pin name Description Input of RF signal l converted from I to V Input of RF signal J converted from I to V. Midpoint voltage (+1.5V) generation output.
  • Page 40 • BD BOARD IC121 digital signal processor, digital servo signal processor, EFM/ACIRC encoder/decoder, shock- proof memory controller, ATRAC encoder/decoder, 2Mbit DRAM (CXD2652AR) Pin No. Pin name Description FOK signal output to system control. MNT0(FOK) H is outputted when in focus. MNT1(SHCK) Track-jump detection signal output to system control.
  • Page 41 Pin No. Pin name Description ASYO Playback EFM duplex signal output. ASYI I(A) Playback EFM comparator slice level input. AVDD – Power supply for analog (+3V). BIAS I(A) Playback EFM comparator bias current input. I(A) Playback EFM RF signal input. AVSS –...
  • Page 42 DG BOARD (2/2) IC502 SYSYTEM CONTROL (RU8X12MF-0021) Pin No. Pin name Description DAOUT0 – not used (OPEN). DAOUOT1 – not used (OPEN). KEY0 – Reserved (“H” level). KEY1 – Reserved (“H” level). KEY2 – Reserved (“H” level). CHACK IN Detection input from chucking-in switch (S685). PACK IN Detection input from back-in switch (not used).
  • Page 43 MAIN BOARD (2/2) IC801 SYSYTEM CONTROL (CXP84648-037Q) Pin No. Pin name Description Pin No. Pin name Description Pin No. Pin name Description PACON Power amplifier control output. JOG0 – Reserved (ground connection). FLSCK1 Communication with FL microcomputer and clock output. MEGABASE Mega-bus control output.
  • Page 44: Block Diagram (1)

    ZS-M7 6-2. BLOCK DIAGRAM (1) • Signal path. : FM : MD PLAY : MD REC : CD – 46 – – 47 – – 48 –...
  • Page 45: Block Diagram (2)

    ZS-M7 6-3. BLOCK DIAGRAM (2) Circuit Boards Location LEFT KEY board FRONT KEY board FILTER board TOP KEY board RIGHT KEY board FM ANT board TRANS board AM ANT board TUNER board PICK-UP RELAY board RELAY board FL board SW board...
  • Page 47: Schematic Diagram -Main Section (1/2)

    6-5. SCHEMATIC DIAGRAM – MAIN SECTION (1/2) – Refer to page 103 for IC Block Diagrams. ZS-M7 Waveforms – Main Section (1/2) – PLAY MODE 2.2 Vp-p 1.1 – 1.5 Vp-p 8.7 sec IC701 #£ (RFO) IC703 @ª (PCO) VOLT/DIV : 200 mV AC VOLT/DIV : 0.5 V AC...
  • Page 48: Schematic Diagram -Main Section (2/2)

    6-6. SCHEMATIC DIAGRAM – MAIN SECTION (2/2) – ZS-M7 Waveforms – Main Section (2/2) – 2 Vp-p 5 MHz IC801 #™ XTAL VOLT/DIV : 0.5 V AC TIME/DIV : 50 nsec 5.2 Vp-p 32 kHz IC801 #¢ TX VOLT/DIV : 1 V AC...
  • Page 50: Tuner Section (Us Model)

    ZS-M7 6-8. SCHEMATIC DIAGRAM – TUNER SECTION (US MODEL) – Refer to page 102 for IC Block Diagrams. Note: Waveform – Tuner Section – • Waveforms are taken with a oscilloscope. • All capacitors are in F unless otherwise noted. pF:...
  • Page 52: Schematic Diagram -Tuner Section (Except Us Model)

    6-10. SCHEMATIC DIAGRAM – TUNER SECTION (EXCEPT US MODEL) – Refer to page 102 for IC Block Diagrams. Waveform – Tuner Section – Note: • All capacitors are in F unless otherwise noted. pF: • Waveforms are taken with a oscilloscope. 50 WV or less are not indicated except for electrolytics Voltage variations may be noted due to normal produc- Note:...
  • Page 53: Schematic Diagram -Bd Section

    6-11. SCHEMATIC DIAGRAM – BD SECTION – Refer to page 100 for IC Block Diagrams. Waveforms – BD Section – PLAY MODE PLAY MODE PLAY MODE 1.3 Vp-p 0.1 Vp-p 0.46 Vp-p IC101 1, 2 I, J IC101 #• RF IC101 4 A VOLT/DIV : 0.2 V AC VOLT/DIV : 0.5 V AC...
  • Page 55: Schematic Diagram -Power Section

    6-13. SCHEMATIC DIAGRAM – POWER SECTION – ZS-M7 Note: • All capacitors are in F unless otherwise noted. pF: 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in W or less unless otherwise specified.
  • Page 57: Schematic Diagram -Dg Section

    6-15. SCHEMATIC DIAGRAM – DG SECTION – Refer to page 102 for IC Block Diagrams. Waveforms – DC Section – Semiconductor Location Ref. No. Location Ref. No. Location D551 Q503 D552 Q504 Q507 0.63 Vp-p IC501 Q509 IC502 Q510 12 MHz IC503 Q511 IC504...
  • Page 60: Schematic Diagram -Front Key Section

    ZS-M7 6-18. SCHEMATIC DIAGRAM – FRONT KEY SECTION – Waveforms – Front Key Section – Note: • All capacitors are in F unless otherwise noted. pF: 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in W or less unless otherwise specified.
  • Page 61 IC Block Diagrams – BD Section – IC101 CXA2523R IC Block Diagrams – Tuner Section – IC121 CXD2652AR IC1 TA2008AN 43 42 USROP – 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 RF AGC –...
  • Page 62 IC Block Diagrams – Main Section – IC701 CXA1992BR PD2 IV PD1 IV SUMMING SENS2 BIAS SENS1 LASER POWER CONTROL F IV AMP FE AMP C. OUT E IV AMP DFCT XRST LEVEL S VEE DATA FO. BIAS WINDOW MIRR COMP.
  • Page 63 IC703 CXD2589Q 59 58 57 54 53 52 51 50 SYSM SERIAL-IN INTERFACE LRCKI LRCK AVSS ASYO OVER SAMPLING DIGITAL FILTER ASYI ASYMMETRY AVDD DEMODULATOR CORRECTOR BIAS 3rd-ORDER AOUT1 NOISE SHAPER AIN1 AVDD LOUT1 AVSS CLTV XVDD TIMING ERROR XTAI LOGIC CORRECTOR AVSS...
  • Page 64 IC702 BA6898FP LEVEL SHIFT LEVEL SHIFT THERMAL SHUT DOWN DRIVER MUTE REG VOLTAGE DOWN, BIAS VOLTAGE DOWN, THERMAL SHUT DOWN MONITOR LEVEL SHIFT LEVEL SHIFT IC301 TDA7439D013TR R IN4 LOUT SPKA ATT SPKA ATT ROUT RIGHT LEFT R IN3 AGND R IN2 VREF SUPPLY...
  • Page 65: Exploded Views

    SECTION 7 EXPLODED VIEWS NOTE : • -XX, -X mean standardized parts, so they • The mechanical parts with no reference The components identified by mark ! may have some difference from the original number in the exploded views are not or dotted line with mark ! are critical one.
  • Page 66: Rear Cabinet Section

    US Model 7-2. REAR CABINET SECTION EXCEPT US Model ANT1 not supplied F953 supplied F952 supplied F951 EXCEPT US Model T951 supplied The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref.
  • Page 67: Chassis Section

    7-3. CHASSIS SECTION not supplied FL401 not supplied not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 101 1-668-249-21 LINE IN BOARD (EXCEPT US) * 107 A-3321-544-A MAIN BOARD, COMPLETE (US) * 101 1-668-249-31 LINE IN BOARD (US) * 107...
  • Page 68: Md Section (1)

    7-4. MD SECTION (1) (MDM-3EG) not supplied not supplied not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 151 A-3321-571-A DG BOARD, COMPLETE (EXCEPT US) 1-783-540-11 WIRE, PARALLEL (FFC) (19 CORE) * 151 A-3321-550-A DG BOARD, COMPLETE (US) 1-790-045-11 WIRE, PARALLEL (26 CORE)(60mm)
  • Page 69: Md Section (2)

    Ver 1.2 2001.07 7-5. MD SECTION (2) (MDM-3EG) not supplied not supplied M901 M902 M903 HR901 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No.
  • Page 70: Cd Section

    7-6. CD SECTION (VLM-ZSM7-142) M691 not supplied CDM-2411AAA Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 251 3-017-025-01 COVER (R), SIDE * 264 3-017-035-01 COVER (L), SIDE * 252 3-017-012-01 PLATE (R), SIDE * 265 3-017-011-01 PLATE (L), SIDE * 253 3-017-014-01 SLIDER (R)
  • Page 71: Optical Pick-Up Section

    7-7. OPTICAL PICK-UP SECTION (CDM-2411AAA) M802 M801 S901 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3303-970-A SCREW ASSY, FEED...
  • Page 72: Electrical Parts List

    SECTION 8 AM ANT AUDIO ELECTRICAL PARTS LIST NOTE : • Due to standardization, replacements in the • SEMICONDUCTORS The components identified by mark ! parts list may be different from the parts In each case, u : , for example : or dotted line with mark ! are critical specified in the diagrams or the components uA..
  • Page 73 AUDIO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R352 1-216-073-00 METAL CHIP 1/10W C168 1-163-038-91 CERAMIC CHIP 0.1uF R353 1-216-059-00 METAL CHIP 2.7K 1/10W C169 1-104-851-11 TANTAL. CHIP 10uF R354 1-216-097-91 RES,CHIP 100K 1/10W C171 1-163-038-91 CERAMIC CHIP 0.1uF R355...
  • Page 74 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > R170 1-216-073-00 METAL CHIP 1/10W R171 1-216-073-00 METAL CHIP 1/10W Q101 8-729-028-91 TRANSISTOR DTA144EUA-T106 R172 1-216-295-00 METAL CHIP 1/10W Q102 8-729-026-53 TRANSISTOR 2SA1576A-T106-QR R173 1-216-121-91 RES,CHIP 1/10W Q103 8-729-028-99 TRANSISTOR DTC114YUA-T106...
  • Page 75 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C528 1-164-156-11 CERAMIC CHIP 0.1uF FB523 1-414-385-11 INDUCTOR, FERRITE BEAD C529 1-124-779-00 ELECT CHIP 10uF FB524 1-414-385-11 INDUCTOR, FERRITE BEAD C532 1-126-603-11 ELECT CHIP 4.7uF FB525 1-414-385-11 INDUCTOR, FERRITE BEAD C533 1-126-603-11 ELECT CHIP 4.7uF...
  • Page 76 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark JC513 1-216-296-00 METAL CHIP 1/8W R509 1-216-857-11 METAL CHIP 1/16W JC514 1-216-296-00 METAL CHIP 1/8W R510 1-216-833-11 METAL CHIP 1/16W JC515 1-216-296-00 METAL CHIP 1/8W R511 1-216-845-11 METAL CHIP 100K 1/16W JC516...
  • Page 77 FILTER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R590 1-216-841-11 METAL CHIP 1/16W C408 1-163-239-11 CERAMIC CHIP 33PF C409 1-163-021-91 CERAMIC CHIP 0.01uF < VIBRATOR > C410 1-163-021-91 CERAMIC CHIP 0.01uF C411 1-104-664-11 ELECT 47uF X501 1-760-174-11 VIBRATOR, CERAMIC (12MHz) C412...
  • Page 78 FM ANT FRONT KEY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R454 1-216-049-91 RES,CHIP 1/10W 1-668-254-21 FM ANT BOARD (EXCEPT US) R455 1-216-049-91 RES,CHIP 1/10W 1-668-254-31 FM ANT BOARD (US) R456 1-216-073-00 METAL CHIP 1/10W ************* R457 1-216-049-91 RES,CHIP...
  • Page 79 FRONT KEY LEFT KEY LINE IN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R414 1-216-029-00 METAL CHIP 1/10W R275 1-216-013-00 METAL CHIP 1/10W R458 1-216-029-00 METAL CHIP 1/10W ************************************************************ R459 1-216-029-00 METAL CHIP 1/10W R460 1-216-029-00 METAL CHIP 1/10W 1-668-243-21 LEFT KEY BOARD (EXCEPT US)
  • Page 80 LINE IN LOADING MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q292 8-729-920-31 TRANSISTOR DTC343TK C122 1-136-165-00 FILM 0.1uF Q392 8-729-027-45 TRANSISTOR DTC114WKA-T146 C123 1-136-165-00 FILM 0.1uF Q399 8-729-027-26 TRANSISTOR DTA114YKA-T146 C124 1-126-960-11 ELECT C125 1-162-927-11 CERAMIC CHIP 100PF <...
  • Page 81 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C717 1-162-965-11 CERAMIC CHIP 0.0015uF 10% C781 1-110-501-11 CERAMIC CHIP 0.33uF C718 1-163-021-91 CERAMIC CHIP 0.01uF C782 1-164-004-11 CERAMIC CHIP 0.1uF C783 1-164-004-11 CERAMIC CHIP 0.1uF C719 1-162-970-11 CERAMIC CHIP 0.01uF C784...
  • Page 82 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C855 1-163-009-11 CERAMIC CHIP 0.001uF D302 8-719-404-49 DIODE MA111 C856 1-163-009-11 CERAMIC CHIP 0.001uF D303 8-719-800-76 DIODE 1SS226 D306 8-719-404-49 DIODE MA111 C857 1-163-009-11 CERAMIC CHIP 0.001uF D711 8-719-404-49 DIODE MA111 C858...
  • Page 83 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC902 8-759-290-19 IC BA3960 Q803 8-729-120-28 TRANSISTOR 2SC1623-L5L6 IC903 8-759-494-77 IC RH5RL58AA-T1 Q902 8-729-027-58 TRANSISTOR DTC143ZKA-T146 Q903 8-729-402-84 TRANSISTOR XN4601 IC904 8-759-442-54 IC RH5RL50AA-T1 Q905 8-729-031-43 TRANSISTOR IMD9A-T108 IC905 8-759-938-15 IC BA178M05 Q909...
  • Page 84 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R708 1-216-847-11 METAL CHIP 150K 1/16W R767 1-216-833-11 METAL CHIP 1/16W R709 1-216-121-91 RES,CHIP 1/10W R768 1-216-857-11 METAL CHIP 1/16W R710 1-216-109-00 METAL CHIP 330K 1/10W R712 1-216-841-11 METAL CHIP 1/16W R769...
  • Page 85 MAIN PICK-UP RELAY RELAY RIGHT KEY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R910 1-216-025-91 RES,CHIP 1/10W 1-668-246-21 RIGHT KEY BOARD (EXCEPT US) R911 1-216-061-00 METAL CHIP 3.3K 1/10W 1-668-246-31 RIGHT KEY BOARD (US) R912 1-216-061-00 METAL CHIP 3.3K 1/10W...
  • Page 86 TOP KEY TRANS Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-668-245-21 TOP KEY BOARD (EXCEPT US) C981 1-164-506-11 CERAMIC CHIP 4.7uF 1-668-245-31 TOP KEY BOARD (US) ************** C982 1-164-506-11 CERAMIC CHIP 4.7uF C983 1-164-506-11 CERAMIC CHIP 4.7uF 3-321-041-11 SCREW (M1.7X4), TAPPING C984...
  • Page 87 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3321-536-A TUNER BOARD, COMPLETE (US) 1-163-009-11 CERAMIC CHIP 0.001uF A-3321-562-A TUNER BOARD, COMPLETE (EXCEPT US) (US) 1-164-344-11 CERAMIC CHIP 0.068uF ********************** (EXCEPT US) < CAPACITOR > 1-163-263-11 CERAMIC CHIP 330PF (EXCEPT US) 1-126-963-11 ELECT...
  • Page 88 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-162-964-11 CERAMIC CHIP 0.001uF 1-164-346-11 CERAMIC CHIP (US) 1-126-924-11 ELECT 330uF 1-163-133-00 CERAMIC CHIP 470PF (EXCEPT US) (EXCEPT US) 1-162-964-11 CERAMIC CHIP 0.001uF < FILTER > (US) 1-163-234-11 CERAMIC CHIP 20PF 1-760-127-11 FILTER, CERAMIC (US)
  • Page 89 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-414-235-11 INDUCTOR, FERRITE BEAD (EXCEPT US) 1-216-025-91 RES,CHIP 1/10W 1-414-235-11 INDUCTOR, FERRITE BEAD (EXCEPT US) (US) 1-414-235-11 INDUCTOR, FERRITE BEAD (US) 1-216-825-11 METAL CHIP 2.2K 1/16W (EXCEPT US) <...
  • Page 90 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-821-11 METAL CHIP 1/16W 1-216-041-00 METAL CHIP 1/10W (US) (EXCEPT US) 1-216-821-11 METAL CHIP 1/16W 1-216-825-11 METAL CHIP 2.2K 1/16W (US) (EXCEPT US) 1-216-821-11 METAL CHIP 1/16W (US) 1-216-295-00 METAL CHIP 1/10W...
  • Page 91 3-861-445-71 MANUAL, INSTRUCTION (POLISH, RUSSIAN) (EE,Russian) 3-861-445-81 MANUAL, INSTRUCTION (CZECH, HUNGALIAN) (EE,Russian) 4-991-047-01 LID, BATTERY CASE (FOR RMT-CM7) 8-917-623-90 REMOTE COMMANDER, SONY RMT-CM7 (US) 8-917-661-90 REMOTE COMMANDER RMT-CM7AD (EXCEPT US) X-3374-655-1 NET (L) ASSY, SP (EXCEPT US) X-3374-656-1 NET (R) ASSY, SP (EXCEPT US)
  • Page 92 ZS-M7 US Model AEP Model SERVICE MANUAL UK Model Tourist Model 2000. 03 SUPPLEMENT - 1 File this Supplement with the Service Manual. Subject : EXPLODED VIEWS (SPM-00011) CHANGED PARTS LIST EXPLODED VIEWS FRONT CABINET SECTION (Service Manual See page 106)
  • Page 93 ZS-M7 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001.07...

Table of Contents