Front Panel Of The Nvr - Swann NVR16-7200 User Manual

English
1
4
2
3
1) Power Button: Press this button to turn on the NVR. The LED will
be blue when the NVR is on and red when the device has been shut
down.
2) Infrared Sensor: Monitors signals coming from the infra-red
remote control. If this sensor is blocked or obstructed, then the
functionality of the remote will be impaired.
3) USB 2.0 Ports: For connecting USB external storage for backup, or
for applying new firmware.
4) Alarm LED: Will be lit when a sensor alarm is detected.
5) Ready LED: Indicates that the NVR is ready and functioning
correctly.
6) Status LED: This will be lit if you are using the supplied remote
control and the device ID is set to 254. It will not be lit if the device
ID is set to 255 (default setting). The LED will turn red when using a
RS485 keyboard.
7) HDD LED: Will flash whenever the NVR is writing to/reading from
the installed hard drive.
8) Tx/Rx (LAN) LED: Flashes rapidly when the NVR's network port is
sending or receiving information.
9) Guard LED: Will be lit when the NVR has been armed. The LED will
turn off when the NVR is unarmed. The arm/disarmed status can be
changed by pressing and holding the ESC button for more than three
seconds in live view mode.
10) DVD Eject Button: If you have a DVD-ROM/Writer installed, this
button will open/close the DVD tray.
11) D-Pad: For navigating around menus when you are not using
the mouse. The enter button is used to confirm your selection. It is
also used to tick checkbox fields and to play/pause video in Playback
mode.
12) These buttons have multiple functions depending on which
mode you are currently in. The text and symbols in blue are the
secondary function:
ESC/Guard: Primary function > Go back to the previous menu,
Secondary function > Press this to arm/disarm the NVR. Press and
hold for more than three seconds in live view mode to arm or disarm.
REC/Shot: Primary function > Enters the Manual: Record menu,
Secondary function > In PTZ mode, you can recall a preset by pressing
this and then one of the alphanumeric numbers. It is also used to turn
the audio on/off in Playback mode.
Play/Auto: Primary function > Enters Playback mode, Secondary
function > Is used to auto scan in PTZ mode.
Zoom+: Is used to increase zoom for a PTZ camera in PTZ mode.

Front Panel of the NVR

5 6 7 8 9
10
12
11
13
A/Focus+: Primary function > Adjust focus in PTZ mode, Secondary
function > Is used to switch between lowercase and uppercase text
input and for symbols and numeric input.
Edit/Iris+: Primary function > Allows you to edit text fields. It will
also function as a backspace button to delete characters in front of
the cursor, Secondary function > Adjusts the iris of the camera in PTZ
mode.
Menu/Wiper: Primary function > Allows you to enter the main menu,
Secondary function > Enables the camera wiper in PTZ mode. In
Playback mode, it is used to show/hide the control toolbar.
F1/Light: Primary function > Is used to select all items on a list when
used in a list field, Secondary function > In PTZ mode, it is used to
turn on/off the PTZ light (if applicable). In Playback mode, it is used
to switch between play and reverse play.
F2/Aux: Primary function > Cycles through the various tabs in the
main menu, Secondary function > In synchronous Playback mode, it
is used to switch channels.
Main/Spot/Zoom-: Primary function > Switch between main and
spot output, Secondary function > Is used to decrease zoom for a
PTZ camera in PTZ mode.
Prev/Focus-: Primary function > Switch between single view and
multi view mode, Secondary function > Adjust focus in PTZ mode in
conjunction with the A/Focus+ button.
PTZ/Iris-: Allows you to enter the PTZ menu, Secondary function >
Adjusts the iris of the camera in PTZ mode.
13) Alphanumeric Buttons: These buttons will allow you to switch
to the corresponding channel in live view and Playback modes.
The buttons will have a different LED status depending on what is
happening:
Blue > The camera is currently recording. The button will not be lit
when the camera is not recording.
Red > When streaming a live image across the network. The camera
is currently not recording.
Pink > When streaming a live image across the network while the
camera is recording.
14) Jog Shuttle Control: In Playback mode, the outer control is used
to speed up or slow down playback and can be used as left/right
control when navigating menus. In live view mode, it can be used
to cycle through the available channels. The inner control is used to
jump ahead or behind 30 seconds in Playback mode and can be used
as up/down control when navigating menus. In PTZ mode, it can be
used to control the movement of a PTZ camera.
14
5