Related Manuals for Kramer RC-3TBU
Summary of Contents for Kramer RC-3TBU
-
Page 1: User Manual
K R A ME R E LE CT R O N IC S L T D . USER MANUAL MODELS: SL-14RC/N Master Controller RC-3TB Remote Control Panel (Optional) RC-3TBU Remote Control Panel (Optional) P/N: 2900-300178 Rev 2... -
Page 3: Table Of Contents
Figure 7: K-NET to RC-3TB/U Connection Figure 8: Daisy-chaining Multiple RC-3TB/U Panels Figure 9: RC-3TBU Connection Method Window Figure 10: RC-3TBU Configurator Software Switch Drop-down List Figure 11: Saving and Loading Projects Figure 12: Sample Button Label Sheet SL-14RC/N – Contents... -
Page 4: Introduction
Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront video, audio, presentation, and broadcasting professionals on a daily basis. In recent years, we have redesigned and upgraded most of our... -
Page 5: Getting Started
Do not secure the cables in tight bundles or roll the slack into tight coils • Avoid interference from neighboring electrical appliances that may adversely influence signal quality • Position your Kramer SL-14RC/N away from moisture, excessive sunlight and dust SL-14RC/N - Getting Started... -
Page 6: Overview
SL-14RC and on the rear panel of the SL-14RCN • IR Learning that learns commands from any IR remote • Compatibility with Kramer Site-CTRL software for network remote control and management over the Ethernet port SL-14RC/N – Overview... - Page 7 • A K-NET™ control channel that can be used to connect to RC-3TB or RC-3TBU Remote Control Panels, or for connecting compatible user interfaces and supplies power and control data over a single cable K-NET™ is a proprietary Kramer protocol for interconnecting Kramer units •...
-
Page 8: Defining The Sl-14Rc/N Master Controller
Defining the SL-14RC/N Master Controller This section defines the SL-14RC/N. Figure 1: SL-14RC/N Master Controller Front Panel Feature Function IR Receiver Accepts IR control ON LED Lights during IR activity Configurable Button Switches 1-10 Function is programmed by the K-Config Configuration software DISPLAY Configurable Button switches 11 and 12 Function is programmed by the K-Config Configuration software Rotary switch up/down LED indicator... -
Page 9: Figure 2: Sl-14Rc/N Master Controller Rear Panel
Figure 2: SL-14RC/N Master Controller Rear Panel Feature Function K-NET Connector Connect the GND pin to the Ground connection; pin B (-) and pin A (+) are for RS-485, and the +12V pin is for powering the unit The ground connection is sometimes connected to the shield of the RS-485 cable (in most applications, it is not connected) SRVC and K-NET TERM For service use only. -
Page 10: Defining The Remote Control Panels
The RC-3TB and the RC-3TBU buttons can be programmed to emulate the buttons on the SL-14RC/N. On the RC-3TB, the assignment of the button emulation is done using the rotary switch. On the RC-3TBU, the assignment is done using the RC-3TBU Software Configurator. - Page 11 Feature Function 8 Position Rotary For assigning which buttons on the SL-14RC/N are Switch emulated by the buttons on the RC-3TB K-NET Termination Terminates the K-NET to RC-3TB daisy-chain Switch K-NET Connector Connects to either SL-14RC/N or additional RC-3TB Front Panel For mounting the RC-3TB Printed Circuit Board Contains the components of the RC-3TB...
-
Page 12: Defining The Rc-3Tbu Remote Control Panel
Figure 3 defines the RC-3TBU. Figure 4: RC-3TBU Remote Control Panel Components Feature Function Mounting Holes 2 holes for mounting the RC-3TBU to the PTBUS-3 or TBUS-6W Buttons 1 to 3 Function assignment is performed using the configurator software K-NET Connector... - Page 13 If there is no K-Net auxiliary device specified in the K-Config control room tree, the K-Net port of the SL-14RC/N will be configured to connect to an RC-3TBU. The RC-3TBU Configurator Software is used to program the buttons of the device...
-
Page 14: Installing In A Rack
Installing in a Rack This section provides instructions for rack mounting the unit. SL-14RC/N - Installing in a Rack... -
Page 15: Connecting The Sl-14Rc/N
Connecting the SL-14RC/N Always switch off the power to each device before connecting it to your SL-14RC/N. After connecting your SL-14RC/N, connect its power and then switch on the power to each device. Figure 5: Connecting the SL-14RC/N Master Controller To connect the SL-14RC/N as illustrated in the example in Figure 1. -
Page 16: Connecting The Rs-232 Interface
Figure 6: RS-232 Connection Connecting the Ethernet Port The Ethernet connection of the SL-14RC/N lets you perform all control functions of the SL-14RC/N over the Internet using a PC running the Kramer Site-CTRL control program. SL-14RC/N - Connecting the SL-14RC/N... -
Page 17: Connecting Rc-3Tb/U Remote Control Panels (Optional)
To connect the SL-14RC/N to a network: 1. Connect the Ethernet port of the SL-14RC/N to the Ethernet port on a network hub or network router, via a straight cable with RJ-45 connectors. 2. At the other end, connect the Internet to a PC running Site-CTRL. 3. -
Page 18: Figure 8: Daisy-Chaining Multiple Rc-3Tb/U Panels
Figure 8: Daisy-chaining Multiple RC-3TB/U Panels Note the position of the termination switch on the first RC-3TB (open, to the right), and that of the second RC-3TB (closed, to the left). When using the RC-3TBU, the same termination scheme must be used. -
Page 19: Operating The Sl-14Rc/N
Web site at www.kramerelectronics.com • RC-3TB/U Remote Control Panels (optional) • A PC running Site-CTRL control software: To operate your device using Site-CTRL, see the Site-CTRL User Guide available at the Kramer Web site SL-14RC/N - Operating the SL-14RC/N... -
Page 20: Installing And Using Rc-3Tbu Configurator Software
The latest version of the RC-3TBU Configurator Software and the Kramer USB driver can be downloaded from http://www.kramerelectronics.com. Note: The RC-3TBU does not need to be connected to a power supply in order to use the software to configure the device. Power to the RC-3TBU is provided by via the USB connection. -
Page 21: Figure 9: Rc-3Tbu Connection Method Window
7. Click to open one of the switch drop-down lists as shown in Figure Figure 10: RC-3TBU Configurator Software Switch Drop-down List 8. Select one of the switches or displays to emulate on the SL-14RC/N. The selection is implemented immediately and stored on RC-3TBU. SL-14RC/N - Installing and Using RC-3TBU Configurator Software... -
Page 22: Saving And Loading A Configuration
The drop-down list appears. 2. Click on Open Project. The Open Project dialog box appears. Navigate to the required folder and select the file. 3. Click Open. The saved configuration is loaded. SL-14RC/N - Installing and Using RC-3TBU Configurator Software... -
Page 23: Front Panel Button Caps And Labels
Front Panel Button Caps and Labels The SL-14RC/N is supplied with a button label sheet and 12 clear, button caps to house the labels. Figure 12 illustrates a sample button label sheet. Figure 12: Sample Button Label Sheet SL-14RC/N - Front Panel Button Caps and Labels... -
Page 24: Installing The Front Panel Button Caps And Labels
10.1 Installing the Front Panel Button Caps and Labels To install the button caps and labels: 1. Remove the required labels from the supplied button label sheet. 2. Remove the supplied button caps from the bag and insert the labels into the button caps. -
Page 25: Technical Specifications
48.3cm x 11.5cm x 1U (19" x 4.5" x 1U) W, D, H (SL-14RC) WEIGHT: 0.6kg (1.4lbs) approx. (SL-14RC) ACCESSORIES: Power cord, rack “ears” OPTIONS: RC-3TB, RC-3TBU Remote Control Panels, IR emitter cables Specifications are subject to change without notice at http://www.kramerelectronics.com RC-3TB/U POWER CONSUMPTION: 12V DC 150mA DIMENSIONS 8.9cm x 2.1cm x 2.3cm (3.5"... - Page 27 " " P/N: 2900- 300178 Rev: 2...
Need help?
Do you have a question about the RC-3TBU and is the answer not in the manual?
Questions and answers