Tascam PA-R200 Instruction Manual page 83

■
Can't connect to the AV receiver from a Web
browser
If you're using DHCP, your router may not always
allocate the same IP address to the AV receiver, so if
you find that you can't connect to a server or Internet
radio station, recheck the AV receiver's IP address on
the "Network" screen.
Check the "Network" settings.
USB Device Playback
■
Can't access the music files on a USB device
Make sure the USB device is plugged in properly.
The AV receiver supports USB devices that support
the USB mass storage device class. However,
playback may not be possible with some USB devices
even if they conform to the USB mass storage device
class.
USB memory devices with security functions cannot
be played.
Others
■
Standby power consumption
In the following cases, the power consumption in
standby mode may reach up to a maximum of 8.3 W:
– The "HDMI Control(RIHD)" setting is set to
"On". (Depending on the TV status, the AV
receiver will enter standby mode as usual.)
– The "HDMI Through" setting is set to other than
"Off".
– The "Network Standby" setting is set to "On".
If an MHL-enabled mobile device is connected to the
AUX (front) input, the power consumption in standby
mode will increase.
■
The sound changes when I connect my
headphones
When a pair of headphones is connected, the listening
mode is set to Stereo, unless it's already set to Stereo,
Mono, Direct, or Pure Audio (European models).
■
The speaker distance cannot be set as required
The values entered may be automatically adjusted
with values best-suited for your home theater.
66
■
The display doesn't work
The display is turned off when the Pure Audio
(European models) listening mode is selected.
66
■
How do I change the language of a multiplex
source
Use the "Multiplex" setting in the "Audio Adjust"
menu to select "Main" or "Sub".
—
96 ■
The functions don't work
To use , you must make an
analog audio connection (RCA) between the
component and AV receiver, even if they are
connected digitally.
—
While Zone 2/3 is selected, the
work.
■
The functions System On/Auto Power On and
Direct Change don't work for components
connected via
65, 67
These functions don't work when Zone 2/3 is turned
on.
■
When performing Automatic Speaker Setup, the
measurement fails and the message "Ambient
noise is too high." is displayed.
This can be caused by a malfunction in your speaker
15
unit. Check if the unit produces normal sounds.
—
En-83
■
The following setting can be made for
composite video inputs
—
• Video Attenuation
If you have a game console connected to the composite
video input, and the picture isn't very clear, you can
attenuate the gain.
—
Video ATT :Off: (default).
Video ATT :On: Gain is reduced by 2 dB.
To make this setting, you must use the buttons on the
AV receiver.
Press the input selector button for the source that you
56
want to set, simultaneously with SETUP. Note that the
input selector must be assigned to a composite video
input. While holding down the input selector button,
press SETUP until "Video ATT :On" appears on the
17
connection and an
AV receiver's display. Then, release both buttons. To
turn the setting off, repeat the above process so that
"Video ATT :Off" appears on the AV receiver's
display, and release the buttons.
17
functions don't
Note
• With the USB input selector, this setting is only available when
an iPod/iPhone is connected and set to Extended Mode (Video)
or Standard Mode.
■
If the picture on your TV/monitor connected to
17 the HDMI output(s) is unstable, try switching the
DeepColor function off
To turn off the DeepColor function, simultaneously
press the STB/DVR and STANDBY/ON buttons on the
AV receiver. While holding down STB/DVR, press
STANDBY/ON until "Deep Color:Off" appears on the
AV receiver's display. Then, release both buttons. To
—
reactivate the DeepColor function, repeat the above
process until "Deep Color:On" appears on the AV
receiver's display and release the buttons.
Appendix