Tascam PA-R200 Instruction Manual page 57

Dolby
■
PL IIx Music (2ch Input)
These settings apply to only 2-channel stereo sources.
If you're not using any surround back speakers, these
settings apply to Dolby Pro Logic II, not Dolby Pro Logic
IIx.
Panorama
On
Off
With this setting, you can broaden the width of the front
stereo image when using the Dolby Pro Logic IIx Music
listening mode.
Dimension
–3 to 0 to +3
With this setting, you can move the sound field forward or
backward when using the Dolby Pro Logic IIx Music
listening mode. Higher settings move the sound field
backward. Lower settings move it forward.
If the stereo image feels too wide, or there's too much
surround sound, move the sound field forward to improve
the balance. Conversely, if the stereo image feels like it's
in mono, or there's not enough surround sound, move it
backward.
Center Width
0 to 3 to 7
With this setting, you can adjust the width of the sound
from the center speaker when using the Dolby Pro Logic
IIx Music listening mode. Normally, if you're using a
center speaker, the center channel sound is output from
only the center speaker. (If you're not using a center
speaker, the center channel sound will be distributed to the
front left and right speakers to create a phantom center.)
This setting controls the front left, right, and center mix,
allowing you to adjust the weight of the center channel
sound.
■
PL IIz Height Gain
Low
Mid
High
The Height Gain Control in Dolby Pro Logic IIz enables
the listener to select how much gain is applied to the front
high speakers. There are three settings, "Low", "Mid" and
"High", and the front high speakers are accentuated in that
order. While "Mid" is the default listening setting, the
listener may adjust the Height Gain Control to their
personal preference.
Note
• If the "Front High" setting is set to "None" (➔ page 54), this
setting cannot be selected.
• If the "Powered Zone 2" setting is set to "Yes" and Zone 2 is
turned on, this setting cannot be selected.
■
Dolby EX
Auto:
If the source signal contains a Dolby EX flag, the
Dolby EX or THX Surround EX listening mode is
used.
Manual:
You can select any available listening mode.
This setting determines how Dolby EX encoded signals are
handled. This setting is unavailable if no surround back
speakers are connected. This setting is effective with
Dolby Digital, Dolby Digital Plus and Dolby TrueHD only.
Note
• If the "Surround Back" setting is set to "None" (➔ page 54),
this setting cannot be selected.
• If the "Powered Zone 2" setting is set to "Yes" and Zone 2 is
turned on, this setting cannot be selected.
En-57
Advanced Operations
■
TrueHD Loudness Management
Off
On
This setting specifies whether or not to apply the Late
Night processing on a Dolby TrueHD source.
Note
• When this setting is set to "Off", the Late Night function for
Dolby TrueHD sources is automatically fixed to "Off".
• When this setting is set to "Off", the Dialogue Normalization
information is not available for Dolby TrueHD sources.
DTS
■
Neo:6 Music
Center Image
0 to 2 to 5
The DTS Neo:6 Music listening mode creates 6-channel
surround sound from 2-channel stereo sources. With this
setting, you can specify by how much the front left and
right channel output is attenuated in order to create the
center channel.
Changing the value from "0" to "5" will spread the sound
of the center channel to left and right (outwards).
®
Audyssey DSX
■
Soundstage
–3dB to Reference to +3dB
With this setting, you can adjust the sound stage when using
Audyssey DSX.
Note
• This listening mode can be selected only when all the following
conditions are satisfied:
– The center speaker is connected.
– The front high speakers are connected.
– Powered Zone 2 is not in use.