OWNERS MANUAL MODEL NO. 625.347050 WITH ELECTRONIC MONITOR UNIVERSAL Undersink Reverse Osmosis HOME DRINKING WATER SYSTEMS Tested and certified to ANSI/NSF Standard 58 for TDS reduction. HOW TO INSTALL HOW IT WORKS CARE OF REPAIR PARTS SAVE THIS MANUAL PRINTED IN UJ;.A.
TABLE OF CONTENTS Safety Guides ..........What Your Home Drinking Water System Will Do ..... Things To Check Before You Start To Install ....... How To Install Your Home Drinking Water System ....5-11 How Your Home Drinking Water System Works ....11-12 Care Of Your Home Drinking Water System .....
SAFETY GUIDES NON-POTABLE WATER SOURCES. DO NOT house water pressure is over the maximum, USE THE SYSTEM ON MICROBIOLOGICAL- install a pressure reducing valve in the water UNSAFE WATER, WATER supply to the Home Drinking Water System. UNKNOWN QUALITY. _, Do not inat_l the Home Drinking Water System CHECK WITH YOUR...
THINGS TO CHECK BEFORE YOU START TO INSTALL • PARTS IN THE SHIPPING CARTON -- Unpack ELECTRONIC FAUCET the carton carefolly so needed parts are not discard- ed by mistake. Included are: _ WATER , SUPPLY TOP COVER _" WATER SUPPLY =WATER PAUC_-'T...
THINGS TO CHECK BEFORE YOU START TO INSTALL REMOTE LOCATION -- You can install the RO • REPLACING ANOTHER RO SYSTEM -- We assembly or water supply saddle valve in another suggest you remove all parts of another RO system, and use everything included with your new RO place away from the RO faucet (please see page system.
HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM STEP 1 INSTALL THE COLD WATER SUPPLY SADDLE VALVE (FIG. 2) • Install this valve on the COLD water pipe to the kitchen sink (FIG. 2). WATER SUPPLY SADDLE VALVE I • This valve has a cuffing pin and will make its own hole in copper or plastic pipe.
HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM INSTALL THE DRAIN CLAMP - continued DRAIN CLAMP • Locate so drain tubing from the faucet (FIG. 7, page 10) makes a straight run to the clamp, without any dips, loops, low spots, or kinks. •...
HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM ASSEMBLE FAUCET AND INSTALL - continued B. ASSEMBLE FAUCET (FIG. 4) 1. Remove the hex nut, and all other parts shown in the dotted line box, FIG. 4. 2.1nsertthefau_tstudthmughthetopgasketand faucetbase. Then, mp_thehexnutandtigh_n. DO NOT OVERTIGHTEN BREAK THE...
HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM tighten the nut. NOTE: Cut tubing as needed for neat appearance, but keep long enough to aillow easy service of the RO system. 7. If needed, cut the 1/4" tubing (marked "1/4" BARB ON FAUCET") to length.
HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM MAKE REMAINING RO CONNECTIONS - continued C. CONNECT TUBING TO WATER SUPPLY Use the tubing insert, ferrule and nut, at the water B. CONNECT TUBING, FAUCET TO DRAIN supply saddle valve, to fasten the remaining 1/4" CLAMP.
HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM the RO system. At that time, carefully check all fit- tings and tubing connections for any water leaks. 1. After the storage bladder has filled (takes about Correct leaks if any are found. 4 hours), open the system faucet until the bladder is empty.
HOW YOUR HOME DRINKING WATER SYSTEM WORKS POSTFILTER - continued light comes on after 6 months, or after 900 gallons of product water use. water. High quality drinking water flows from the • FLASHING AMBER "RO" - The RO membrane postfiher and to the faucet.
CARE OF YOUR HOME DRINKING WATER SYSTEM PREFILTER CARTRIDGE - You must replace POSTFILTER. Always replace the postfilterat the the prefilter cartridge often to protect the RO mem- same time you replace the prefilter cartridge. The brane from being destroyed by chlorine, and/or from postfilter gives the product water a final filtering of any tastes and/or odors that may remain.
CARE OF YOUR HOME DRINKING WATER SYSTEM RO MEMBRANE CARTRIDGE - The useful life for the RO membrane to become useless. A small, cone-shaped screen is positionedover the flow con- of the membrane cartridge depends mostly on the pH (see page 17) of your supply water. The lower trol (FIG.
CARE OF YOUR HOME DRINKING WATER SYSTEM Install the RO housing, push downward and SANITIZING THE RO SYSTEM rotate 90 o clockwise to lock in place. Sanitizing is recommended upon installation of the Replace the tank shutoffvalve and rotate 900 to RO system, and after servicing inner parts of the lock.
CARE OF YOUR HOME DRINKING WATER SYSTEM RO CARE GUIDE MODEL NO. 625.347050 WITH MONITOR IMPORTANT: BEFORE DOING "rite FOLLOWING MAINTENANCE, BE SURETO RELIEVE PRESSURE AND ALLOW AIR TO ENTER THE TANK, STEPS 1, 2 AND 3, PAGE 12. 1. Rep_ce the preffitet cartridgeand postfilterwhen the amber "FILT"light beginsto flash whiletlddng!0n)duct water fromthe RO faucet.
DIMENSIONS - SPECIFICATIONS _=-_-1 O- 1/2'"-----q= 21-1/2" METRIC 280-860 kPa Supply water pressure limits ........40-125 PSI 5-40oC. Supply .water temperature limits ...., ....... 40-100OF Maximum total dissolved solids ('FDS)....... 2000 PPM Maximum water hardness @ 6.9 pH ........10 GPG Maximum iron, manganese, hyd.
REPAIR PARTS Kenmore HOME DRINKING WATER SYSTEM Underslnk Reverse Osmosis MODEL NO. 625.347050 DRAIN CLAMP FAUCET AIR GAP 1/4" BARB SADDLE VALVE...
REPAIR PARTS Kenmore HOME DRINKING WATER SYSTEM Undersink Reverse Osmosis MODEL NO. 625.347050 PART PART NUMBER DESCRIPTION OF PART NUMBER DESCRIPTION OF PART Faucet 7110466 ROCap 7095925 126O6OO Washer 7124986 Elbow, 114" NFT x 1/4" Tubing 7064144 Adaptor (Incl. Key Nos. 2 and 4)
OWNERS WATER SYSTEMS MANUAL Now that you have purchased your Kenmore Home Drinking Water Sys- tem, should a need ever exist for repair parts or service, simply contact SERVICE any Sears Service Center. Be sure to provide all pertinent facts when you...