Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Intergraph Intense 3D Pro 2200S
Summary of Contents for Intergraph Intense 3D Pro 2200S
- Page 1 Intense 3D Pro 2200S Installation Guide December 1997 DHA025800...
- Page 2 The software discussed in this document is furnished under a license and may be used or copied only in accordance with the terms of the license. No responsibility is assumed by Intergraph for the use or reliability of software on equipment that is not supplied by Intergraph or its affiliated companies.
- Page 3 If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, try to correct the interference as follows: reorient or relocate the affected device; increase the separation between this equipment and the affected device;...
- Page 4 Product Serial Number Record the serial number printed on the Intense 3D Pro 2200S board before installing the board in your computer. You will need this number to get technical support and warranty service. You can record the serial number in Chapter 2, “Preparing for Installation.”...
- Page 5 Introduction Congratulations! In choosing Intense 3D Pro 2200S, you are equipping your personal computer or personal workstation with powerful and professional 3D graphics. Intense 3D Pro 2200S infuses Intel Pentium Pro and Pentium II computers running the Microsoft Windows NT operating system with workstation-class 3D graphics features and performance.
-
Page 6: Hardware Configurations
You must leave an open slot adjacent to side 1 (the side with the texture memory module connector) of each installed Intense 3D Pro 2200S board, unless you install the board in a slot in which side 1 is not adjacent to another slot. This ensures proper cooling for the board’s high-power... - Page 7 More information on the Heidi Device Driver and Intergraph’s RenderGL graphics library is available on Intergraph Online (see Chapter 5).
-
Page 9: Preparing For Installation
Preparing for Installation Follow these instructions to prepare your computer for Intense 3D Pro 2200S. Make Sure Your Computer Is Ready Make sure your IBM PC-compatible computer has the following: A Pentium Pro or Pentium II processor. A high-resolution multi-sync analog RGB monitor. Windows NT 4.0 operating system. -
Page 10: Collect Materials And Tools
2200S hardware in its original packaging to obtain warranty service. Record the Board’s Serial Number You must have the serial number of your Intense 3D Pro 2200S board to get technical support or warranty service. Before you install the Intense 3D Pro 2200S board in your computer,... -
Page 11: Read The Instructions
Read the Instructions Before installing Intense 3D Pro 2200S, read Chapter 3, “Installing the Hardware,” and Chapter 4, “Installing the Software” completely. You may want to review the... -
Page 13: Installing The Hardware
(if present), and adding expansion boards. Add Texture Memory If you want to add texture memory to an Intense 3D Pro 2200S board, do so before you install the board in the computer. To add texture memory: Place the Intense 3D Pro 2200S board on a solid, flat, non-static surface. -
Page 14: Start The Installation
If your computer has a graphics accelerator integrated onto the system board, disable it. Select the PCI expansion slots into which you will install the Intense 3D Pro 2200S board. Select one open PCI slot for each board you want to install. WARNING... -
Page 15: Finish The Installation
Intense 3D Pro 2200S board Finish the Installation To finish the installation: Close the computer. Connect the computer monitor’s video cable to the blue video output port on the Intense 3D Pro 2200S board. See the following figure. - Page 16 See the previous figure. Turn on the computer. The video display starts in VGA mode. Install the Intense 3D Pro 2200S video display driver as instructed in Chapter 4, “Installing the Software.”...
-
Page 17: Installing The Software
Install the Intense 3D Pro 2200S Video Display Driver To install the Intense 3D Pro 2200S video display driver: Insert the diskette containing the video display driver into the computer’s floppy disk drive. -
Page 18: Configure The Video Display
Open Display in the Control Panel to view the Display Properties dialog. Use the dialog tabs to configure the operation of the computer’s video display when it is controlled by the Intense 3D Pro 2200S Graphics Accelerator. For example, click the Settings tab to change the screen resolution. -
Page 19: Activate Multi-Screen Behavior
Activate Multi-Screen Behavior If your computer is configured for multi-screen display (with multiple Intense 3D Pro 2200S Graphics Accelerators installed), the video display driver treats the combined display area as a single canvas that covers all screens. In this Full Canvas style, windows centered on the canvas may be split between screens. -
Page 21: Getting Help
Getting Help Use the information in this chapter if you encounter a problem with Intense 3D Pro 2200S, if you want to get product information or fixes, or if you want to contact Intergraph for help. World Wide Web If your computer has a World Wide Web browser, connect to the Intense 3D Pro pages at http://www.intergraph.com/ics/intense3d for... -
Page 22: Intergraph Faxlink
Getting Warranty Service Contact the original place of purchase to get warranty service for your Intense 3D Pro 2200S board. If your warranty period has expired, you may still be eligible for warranty service from Intergraph. Refer to the warranty statement at the beginning of this document for details. - Page 23 To get warranty service for Intense 3D Pro 2200S: Call the Customer Response Center at 1-800-633-7248. Tell the operator you want to return an Intense 3D Pro 2200S board for service, and give the operator the serial number found on the board.
-
Page 25: Technical Information
12V 30 mA +5V 0.87 A +3.3V 4.8 A Monitor Resolutions Intense 3D Pro 2200S supports standard multi-sync monitors, including Intergraph 17-inch and 21-inch multi-sync monitors, at the following resolutions and maximum refresh rates (Hz). Note that i indicates an interlaced frequency. - Page 26 81 (20), 79 (27) 1280 x 1024 5 x 4 76 (20), 72i (20), 74 (27), 70i (27) Intense 3D Pro 2200S supports InterView 28hd96 monitors at the following resolutions and maximum refresh rates (Hz). Note that i indicates an interlaced frequency. Aspect...
-
Page 27: Vga Video Display Support
Interfaces The Intense 3D Pro 2200S Graphics Accelerator has two interfaces: a video output port, and a stereo sync output port. These interfaces are described in the following sections. -
Page 28: Video Output Port
Video Output Port The video output port is a blue, female, 15-pin, D-Sub connector. The port provides connection to a computer monitor. The recommended cable length is less than three meters. Signal Name Signal Name Red Analog Video +5V Supply Green Analog Video Ground Blue Analog Video... -
Page 29: Stereo Sync Output Port
Stereo Sync Output Port The stereo sync output port is a female, 5-pin, mini-DIN connector. The port provides connection to the emitter module of a pair of LCD shutter glasses. Signal Name Ground Ground +12V Stereo Sync No Connect...