Program Change - Roland MV-8800 Appendices

❍ Portamento control (Controller number 84)
Status 2nd byte
BnH
54H
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = source note number: 00H - 7FH (0 - 127)
* A Note-on received immediately after a Portamento Control message will change
continuously in pitch, starting from the pitch of the Source Note Number.
* If a voice is already sounding for a note number identical to the Source Note Number, this
voice will continue sounding (i.e., legato) and will, when the next Note-on is received,
smoothly change to the pitch of that Note-on.
* The rate of the pitch change caused by Portamento Control is determined by the
Portamento Time value (PATCH EDIT (SOLO/PORTAMENTO) screen).
❍ Effect 1 (Reverb Send Level) (Controller number 91)
Status 2nd byte
BnH 5BH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Reverb Send Level: 00H - 7FH (0 - 127)
❍ Effect 3 (Chorus Send Level) (Controller number 93)
Status 2nd byte
BnH 5DH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Chorus Send Level: 00H - 7FH (0 - 127)
● Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H - FH (ch.1 - 16)
pp = Program number: 00H - 7FH (Pattern Library 001 - 128)
* Program change that received each MIDI channel number will function as the patch
change.
● Channel Pressure
Status 2nd byte
DnH vvH
n = MIDI channel number: 0H-FH (ch.1-16)
vv= Channel Pressure: 00H-7FH (0-127)
● Pitch Bend Change
Status 2nd byte
EnH llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
ll, mm = Pitch Bend value: 00, 00H - 00, 40H - 7F, 7FH (-8192 - 0 - +8191)
3rd byte
kkH
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
■Channel Mode Messages
● All Sound Off (Controller number 120)
Status 2nd byte
BnH 78H
n = MIDI channel number: 0H-FH (ch.1-16)
* When this message is received, all notes currently sounding on the corresponding
channel will be turned off.
● Reset All Controllers (Controller number 121)
Status 2nd byte
BnH 79H
n = MIDI channel number: 0H-FH (ch.1-16)
* When this message is received, the following controllers will be set to their reset values.
Controller Reset value
Pitch Bend Change +/-0 (center)
Polyphonic Key Pressure 0 (off)
Channel Pressure 0 (off)
Modulation 0 (off)
Expression 127 (max)
Hold 1 0 (off)
● All Notes Off (Controller number 123)
Status 2nd byte
BnH 7BH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When All Notes Off is received, all notes on the corresponding channel will be turned off.
However, if Hold 1 is ON, the sound will be continued until these are turned off.
● OMNI OFF (Controller number 124)
Status 2nd byte
BnH 7CH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received.
● OMNI ON (Controller number 125)
Status 2nd byte
BnH 7DH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received. OMNI ON will
not be turned on.
● MONO (Controller number 126)
Status 2nd byte
BnH 7EH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = mono number: 00H - 10H (0 - 16)
* The same processing will be carried out as when All Notes Off is received.
* The Mono Mode parameter (PATCH EDIT (SOLO/PORTAMENTO) screen) of the part
that corresponds to received MIDI channel will be turned On.
● POLY (Controller number 127)
Status 2nd byte
BnH 7FH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received.
* The Mono Mode parameter (PATCH EDIT (SOLO/PORTAMENTO) screen) of the part
that corresponds to received MIDI channel will be turned Off.
■System Realtime Message
● Active Sensing
Status
FEH
* When Active Sensing is received, the unit will begin monitoring the intervals of all further
messages. While monitoring, if the interval between messages exceeds 420 ms, the same
processing will be carried out as when All Sounds Off, All Notes Off and Reset All
Controllers are received, and message interval monitoring will be halted.
MIDI Implementation
3rd byte
00H
3rd byte
00H
3rd byte
00H
3rd byte
00H
3rd byte
00H
3rd byte
mmH
3rd byte
00H
A-67
MV-8800 Appendices