Table of Contents
Advertisement
SIDE BROOM HEIGHT ADJUSTMENT
NOTE
Brooms of various hardness are available. This
procedure is applicable to all types of brooms.
1.
Check the side broom is at the correct height from the
ground, proceeding as follows:
– Drive the machine on a level ground and lower the
side broom.
– Keep the machine stationary and rotate the side
broom for few seconds.
– Stop the side broom and move the machine.
– Check that the side broom print is, in extension
and orientation, as shown in the figure (1, Fig. J).
In case the print is not within the specifications, it
is necessary to adjust the broom height,
proceeding as described in step 6.
2.
Rotate the knob (10, Fig. C) clockwise or
counter-clockwise to adjust the broom height from the
ground.
3.
Perform step 1 again to check the proper adjustment
of the side broom height from the ground.
4.
When the broom is too worn to be adjusted, replace it
as shown in the next paragraph.
SIDE BROOM REPLACEMENT
NOTE
Brooms of various hardness are available. This
procedure is applicable to all types of brooms.
CAUTION!
It is advisable to use protective gloves
when replacing the side broom because
there can be cutting debris between the
bristles.
1.
Drive the machine on a level ground and activate the
pedal brake (25, Fig. C) (if present).
2.
Remove the key (2, Fig. B) from the machine on/off
switch.
3.
Introduce the hand inside the side broom and press
the tabs (1, Fig. K) inwards, then remove the broom
(2) disengaging it from the four pins (3).
4.
Install the new broom on the machine engaging it on
the pins (3) and on the tabs (1).
5.
Carry out the side broom height adjustment as
described in the previous paragraph.
146 2592 000(1)2005-03 A
USER MANUAL
DUST FILTER CLEANING AND INTEGRITY
CHECK
NOTE
Besides the standard paper filter, optional
polyester filters are also available. The
following procedure is applicable to each type
of filter.
1.
Drive the machine on a level ground and activate the
pedal brake (25, Fig. C) (if present).
2.
Remove the key (2, Fig. B) from the machine on/off
switch.
3.
Disengage the retainer (17, Fig. C).
4.
By means of the handle (18, Fig. C) pull out the
hopper (16).
5.
Turn the handle (1, Fig. L) upwards (90°
approximately) and let the filter frame (2) rotate
outwards.
6.
Pull out the dust filter (3) upwards.
7.
In an outdoor area, clean the filter shaking it on a level
and clean surface, tapping the side (1, Fig. M),
opposite to the wire gauze (2).
8.
Complete the cleaning by means of a compressed air
perpendicular jet (3) of max. 6 bars, blowing only from
the side protected by the wire gauze (2).
9.
Check the filter body for tears.
According to the filter type, observe the following
cautions:
– Paper filter (standard), do not use water or
detergents to clean it; the filter can be damaged.
– Polyester filter (optional): for a better cleaning, it
is allowed to wash the filter with water and
non-frothing detergents. This provides better
quality cleaning but reduces the life of the filter,
which will have to be replaced more frequently.
The use of unsuitable detergents can damage the
filter.
10. If necessary, clean the filter compartment rubber seal
(4, Fig. L) along its perimeter and check its integrity.
If necessary, replace it.
11. Reassemble in the reverse order of disassembly.
NOTE
Reinstall the filter with the wire gauze (2, Fig.
M) facing the front part of the machine (facing
the fan (24, Fig. U)).
ENGLISH
FLOORTEC 560 P
11
Advertisement
Table of Contents
