Erasing All Tracks (Disc Erase Function) - Panasonic SL-PR300 Operating Instructions Manual

SL-PR300EB.fm Page 37 Thursday, September 20, 2001 3:42 PM
Special Recording Edit Operations
4
Press the SET button (main unit/remote
control).
• "ERASE (start track) – (last track)?" is flashed in the informa-
tion display. (Initially, the start track and last track are both the
last track number recorded on the CD-RW.)
• Press the CANCEL button (main unit/remote control) if you do
not wish to perform this procedure.
5
If needed, use the MULTI JOG control or press
the P / p (menu) button on the remote control to
select the number of tracks you want to erase
preceding the last track.
• Please note that all tracks following the start track will be
erased. For example, when track 8 on an 11 track CD-RW is
assigned as the start track, tracks 8, 9, 10, and 11 will be erased.
6
Press the SET button (main unit/remote
control).
• "ERASE TRACK" is flashed in the information display, the
selected tracks are erased, and the normal display is shown
when erasing has been completed.
• Each track that was erased is cleared from the music calendar.
• Tracks can only be erased starting from the last track recorded
on a disc.
Notes
• Once a track is erased, the recording cannot be restored.
• Do not turn the power off, disconnect the AC power cord from
the wall outlet or subject the unit to vibration during the erase
operation. Doing so may ruin the CD-RW disc.
Erasing All Tracks (Disc Erase
Function) (CD-RW only)
The Disc Erase function is used to erase the entire contents of the
CD-RW. This unit uses a unique high-speed (2x) erasing function
that is different from normal erasure procedures. Erasing is per-
formed all the way through the disc's TOC (Table of Contents).
"ERASE DISC" flashes in the information display during the eras-
ing process.
Note
• If the disc is damaged or there is disc related trouble, this func-
tion may not be possible.
COMPACT DISC RECORDER SL-PR300
OPEN / DISC
CLOSE SELECTOR
3
3
DISC
2
DISC 2
DIGITAL
1
DISC
PHONES 1
MIN MAX
PLAY MODE CD EDIT CD REC
DISC SELECTOR
CD1 CD2 CD3
CD REC CD EDIT FINALIZE
1 2
4 5
7 8
_ >
0 10
PLAY
MODE REPEAT
•
REC FADE
3
REC MUTE
+
PITCH
SET
PITCH–
COMPACT DISC RECORDER
RAK-PR300
1
Load the CD-RW to be erased in the CDR disc
tray.
• The number of tracks and play time are shown in the informa-
tion display.
2
When the unit is in the stop mode, press the
MENU button (main unit/remote control).
3
Turn the MULTI JOG control or press the
(menu) button on the remote control until "DISC
ERASE" is shown in the information display.
4
Press the SET button (main unit/remote
control).
• "ERASE DISC?" is shown in the information display.
• Press the CANCEL button (main unit/remote control) if you do
not wish to perform this procedure.
5
Press the Set button (main unit/remote control).
• Full disc erasure takes a few minutes to perform. During the
procedure, the length of the level meter is used to indicate
approximately how much time is remaining until erasure is
complete. When the erasure has been completed, the normal
display is shown.
1
MULTI JOG
REC LEVEL
– + 3
OPEN /
CLOSE
CD LINE REC SELECTOR
MIX BALANCE
LINE CD
SYNCHRO MENU SET CANCEL
REC/
FINALIZE REC MUTE
2 4,5
CANCEL
DISPLAY
3
6
9
CONTROL
CD CD-R/RW
SYNCHRO
2
4,5
CANCEL
R F
/
RQT6091