Auto Pan Setup - JVC TK-C655 Instructions Manual

AUTO PAN Setup

Use the AUTO PAN screen to set the auto pan function, which allows the camera to be revolved slowly in a horizontal direction.
The auto pan function has three modes, the RETURN mode for continual movement between two positions, the RIGHT mode for
clock-wise rotation and the LEFT mode for counterclockwise rotation.
Slow movement
MENU button
SET button
REMOTE CONTROL UNIT
CAMERA POSITION
SETUP POWER
ALARM
MENU SET AUTO
KEY LOCK
LENS CAMERA/POSITION
1 2 3
CAMERA POSI-
SPEED
TION
4 5 6
CLOSE IRIS OPEN OPTION OPTION
1 2
FOCUS
7 8 9
NEAR FAR AUTO AUTO
AF
PAN PATROL
0
WIDE ZOOM TELE CLEAR ENTER
/HOME
ENTER button
FAR button
WIDE button
NEAR button
– – – A U T O P A N / P A T R O L / T R A C E – – –
A U T O P A N M O D E R E T U R N
A U T O P A N S P E E D N O R M A L
A . P A N S T A R T P O S . S E T . .
A . P A N R E T U R N P O S . S E T . .
A U T O P A T R O L S E T . .
A U T O T R A C E S E T . .
R M A . P A N K E Y A . P A N
R M A . P A T R O L K E Y A . P A T R O L
AUTO PAN/PATROL/TRACE menu
– – – S T A R T P O S I T I O N S E T – – –
M E N U / /
P U S H S A V E & R E T U R N
START POSITION SET screen
– – – R E T U R N P O S I T I O N S E T – – –
/
P U S H M E N U S A V E & R E
RETURN POSITION SET screen
RM-P2580
F-1 F-2 F-3
CAMERA
PAN/TILT
button
PAN/TILT
lever
TELE button
T U R N
1.
Select the camera. (
CAMERA button → Numeric key (camera number) → ENTER button.
The picture of the selected camera is output.
2.
Display the SETUP menu on the camera.
☞
1
( P. 20, steps to
MENU button (3 sec.) → Select "CAMERA" with the PAN/TILT lever
→ SET button.
3.
Tilt the PAN/TILT lever up or down to move the cur-
sor (>) to "AUTO PAN/PATROL/TRACE" and press
the SET button.
The AUTO PAN/PATROL/TRACE menu is displayed.
4.
Set the auto pan mode and speed.
• Select the "AUTO PAN MODE" item and then select either RE-
TURN (continual movement between two positions),
RIGHT(clockwise rotation) or LEFT (counterclockwise rotation).
• Select the "AUTO PAN SPEED" item and then select either LOW,
NORMAL or HIGH.
5.
Move the cursor (>) to "A. PAN START POS. SET"
and press the SET button.
The START POSITION SET screen is displayed.
6.
Adjust the viewing angle of the start position.
• Use the PAN/TILT lever, FOCUS button and ZOOM button to ad-
just the viewing angle.
• Tilting of the camera and changes in lens controls such as the
FOCUS and ZOOM settings are not available at the return posi-
tion.
7.
Press the MENU button.
The AUTO PAN/PATROL/TRACE screen shows "DATA SAVED" to
indicate that the viewing angle for the start position has been regis-
tered.
8.
Move the cursor (>) to "A. PAN RETURN POS. SET"
and press the SET button. (RETURN mode only)
The RETURN POSITION SET screen is displayed.
9.
Adjust the viewing angle of the return position.
(RETURN mode only)
Pan the camera in the right and left directions and adjust the view-
ing angle.
10.
Press the MENU button.
• The screen returns to the previous menu.
MEMO
• It is not possible to tilt the camera or change the lens settings at
the return position.
• If the SET or MENU buttons are pressed while the camera is mov-
ing, the correct settings cannot be registered. Make sure that the
camera is stationary before pressing the SET or MENU buttons.
After the above setup, auto panning of the camera can be started by
pressing the AUTO PAN button on the RM-P2580.
☞
"Auto Panning" in the RM-P2580 Instruction manual.
☞
RM-P2580 Instruction manual)
4
)
37