Summary of Contents for JVC TK-C700U - Color Cctv Camera
COMBINATION CAMERA TK-C675B INSTRUCTIONS For Customer Use : Enter below the Serial No. which is located on the body. Retain this information for future reference. This instruction book is made from 100% recycled paper. Model No. TK-C675B Serial No.
This device complies with Part 15 of the FCC Rules. Cet appareil numénque de la classe [B] respecte toutes les Changes or modifications not approved by JVC could void exigences du Réglement sur le matériel brouilleur du Canada. the user's authority to operate the equipment.
Operating precautions To save energy, when it is not being used turn the system's The electronic shutter of this camera has been set to 1/60(1/ power off. 50) sec. at the factory. When the camera is used under a This camera has been designed for indoor use. It cannot be fluorescent lamp or in an area with a local power frequency used outdoors.
Controls, connectors and indicators Ceiling mount Camera body (Front) Dome cover lens Dome cover Camera position alignment mark (Back: Camera side) Ventilation View when the camera body cover is removed safety wire from the ceiling through these holes. VIDEO OUTPUT terminal Outputs composite video signals and is to be connected Terminal board cover to a monitor, etc.
Installation Make a hole (90 mm dia.) in the ceiling for passing through the connection cables. ø90mm Connect the cables to the terminal board. Turn the power of all the connected equipment to OFF before connecting the cables. Remove the terminal board cover and connect the video signal Remove the terminal board cable (coaxial cable),the control signal cables ( 4) and the AC cover by flipping it up while...
Installation (continued) Turn the camera body cover to anti clockwise to set the word “RELEASE” on the camera body cover over the mark, then pull the camera body cover upward. Transportation bracket is mounted when it is shipped from the factory.
Installation (continued) Attach the camera body cover. Camera body cover Align "RELEASE on the camera body cover with the indi- cation mark on the camera body, fit the cover onto the cam- era body, then rotate the cover clockwise until “LOCK” is indicated.
Connections CAUTION If this camera and the cables connected to this camera is used where there are strong electromagnetic waves or where there is magnetism present, for example near a radio or TV transmitter, power transformer or an electric motor, the picture may produce noise and the colors may be affected.
Connections (continued) control signal connection Use a twisted-pair cable for the connection. Duplex Simplex When the camera is controlled with the full duplex proto- When the camera is controlled with the simplex transmis- col, set SW5 to OFF. sion protocol, set SW5 to ON. Camera Controller Camera...
Menu settings This chapter shows an example of connection to the JVC’s remote control unit RM-P2580. Read it and refer also to the instruction manual of the RM-P2580. Menu operations It is possible to set the menu screen of the remote control unit (RM-P2580).
Menu settings (continued) Menu screen flow The menu screen flow is as follows. For details, see the reference pages. Normal screen CAMERA MODE SELECT screen Camera SETUP screen C A M E S E L E C T S E T U P C A M E E L E C T .
Menu settings (continued) CAMERA MODE SELECT screen Variable Factory Item Function range setting V.PHASE Set when adjusting the vertical of other cameras operating in 0 ~ 255 the line lock (LL) mode. Adjust while viewing the screen. The value will become smaller when the pan/tilt lever is pressed to the left (8).
Menu settings (continued) CAMERA VIDEO ADJUST screen Variable Factory Item Function range setting AGC MODE The maximum gain of the AGC (Automatic gain control) is set. 12 dB This setting value becomes a maximum limit when the gain is 12 dB automatically changed according to brightness.
Menu settings (continued) VIDEO ADJUST FOR POSITION screen Variable Factory Item Function range setting POSITION TEXT It is possible to set up to 16 characters to use as titles for set positions (max. 63) and home positions (max. 1). See the next page for details on settings MEMO Always register positions before setting titles.
Menu settings (continued) POSITION TEXT screen It is possible to set titles to positions (max. 63) and home positions (max. 1) using text of 16 characters or less. MEMO Always register positions before setting titles. Positions cannot be selected when they are not registered. To register positions, see the instruction manual of the used remote control unit.
Menu settings (continued) CAMERA TEXT screen It is possible to set up to 16 characters to use as a title during camera selection. MENU PAN/TILT button button control lever REMOTE CONTROL UNIT REMOTE CONTROL UNIT RM-P2580 CAMERA POSITION SETUP POWER POWER ALARM MENU...
Menu settings (continued) AREA TEXT screen The 360° panning angle (horizontal rotation) is divided into 16 sectors, allowing you to check the title in each area. When the camera is manually panned, the preset area designation is shown on the screen. It is possible to set titles of 16 characters or less to each area.
Menu settings (continued) ALARM TEXT screen It is possible to set up to 12 characters to use as a title during alarm. MENU PAN/TILT button button control lever REMOTE CONTROL UNIT REMOTE CONTROL UNIT RM-P2580 CAMERA POSITION SETUP POWER ALARM MENU AUTO KEY LOCK...
Menu settings (continued) AUTO PAN SET screen Auto pan is a feature which allows the camera to slowly move sideways automatically and is set per each camera. There are 3 AUTO PAN modes: RETURN that goes back and forth between two points, RIGHT that makes a right rotation and LEFT that makes a left rotation.
Menu settings (continued) AUTO PATROL SETUP screen The auto patrol is a feature to move the camera to multiple positions at high speed in a set sequence and time and is set per each camera. MENU PAN/TILT button button control lever High speed REMOTE CONTROL UNIT REMOTE CONTROL UNIT...
Menu settings (continued) FACTORY SETTINGS screen It is possible to return all camera settings to the factory settings. MENU PAN/TILT button button control lever REMOTE CONTROL UNIT REMOTE CONTROL UNIT RM-P2580 CAMERA POSITION SETUP POWER POWER ALARM MENU AUTO KEY LOCK KEY LOCK Numeric Key buttons...
Troubleshooting Symptom Cause (Information) Remedy Video is not • Is there a problem in the power cables con-nect- • Connect low resistance cables. output. ing the camera to the power supply unit. • Place the AC 24V power supply near to the camera. (If the power cables are too long or are of the wrong (Check that the voltage supplied to the terminal size, the correct voltage may not be supplied due...
Specifications CAMERA MOVING MECHANISM Signal system : U type Based on NTSC standard Panning : 360 degree endless E type Based on PAL standard Tilting : 0 to 90 degrees Image device : 1/3"IT CCD Panning speed : 240 degree/sec, 80 degree/sec, Effective picture : U type 380,000 pixels, 771 (H) 492 (V) 60 degree/sec, 40 degree/sec,...