Advertisement
23" (58,3 cm)
max, recessed
depth
20=1/2"
(52,1 cm}
overall
height
27" (68.6 Cm)m/w Oven
25-3/8" (64.5 cm)
26-3/4" (67.9 cm)
30" (76.2 cm)mlw oven
28-3/8'! (72.1 cm)
29=314'! (75.6 cm)
7-
19=7/16"
(4&4 cm}
cutout
height
1=1/2"
{3&1 cm}
min.
bottom
of
cutout to
top of
cabinet
door
cabinet
width
B
_--
cutout
--
width
1" (25,4 cm)
top of cutout
to bottom
of upper
cabinet
door
40"
{101,2 cm)
bottom
of
cutout to
floor
cabinet
_
23ol/4" {5&1 cm} ___
min, cutout
depth
23" (5&4 cm)
recessed
oven
depth
recessed
oven
oven
"//front
Cabinet side view
Electrical supply junction box shouM be Uocated
3 inches (7.6 cm) maximum beUowthe support
surface when oven is installed in a wall cabinet.
Cutout for wiring should be in the right rear or
left rear corner. For undercounter installation, it
is recommended that the junction box be
located in the adjacent right or left cabinet. If
installing junction box on rear wall behind
oven, junction box must be recessed and
located in the upper or lower right or left corner
of cabinet.
'
°
A
'
B ¸¸
'
27" (68.6 cm) m/w oven
27" (68.8 Cm)25-1/2"
(64.8 Cm)
30'! (76.2 Cm)m/w oven
30'! (76.2 cm)
28q/2" (72.4 cm)
Tool needed:
Phillips screwdriver
Parts supplied:
_2
screws
Copies of the standards
listed may be obtained from:
Nationa_
Fire Protection
Association
One Batterymarch
Park
Quincy,
Massachusetts
02269
_
CSA International
850I
East Pleasant
Valley
road
C_eveJand, Ohio 44131-5575
Page 1
Yoursafety and the safety of othersare
very important.
We have provided many important safety
messages in this manual and on your appliance=
Always read and obey nil safety' messages.
This is the safety'alert symbol.
This symbol alerts you to potentiai hazards
that can kiii or hurt you and others.
Ati safety messageswiii foliow the safety alert
symbol and either the word "DANGER"or
"WARNING".Thesewords mean:
You can be killed or seri0usty injured if y0u
don't feH0w instructions.
Aii safety messageswiii teti you what the potential
hazard is, toil you how to reducethe chance of
mjury, and teti you what can happen if the
instructions are not followed.
important: Observe all governing
codes
and ordinances.
Proper installation is your responsibility.
Have a qualified technician install this oven.
Oven location should be away from strong
draft areas, such as windows, doors and strong
heating vents.
Cabinet opening dimensions that are shown
must be used. Given dimensions provide
minimum clearance.
Recessed installation area must provide
complete enclosure around the recessed
portion of the oven.
ElectricaJ ground is required. See "Electrical
requirements."
EiectricaJ supply junction box should be located
3 inches (7.6 cm) maximum below the support
surface when oven is installed in a wall cabinet.
Cutout for wiring should be in the right rear or
left rear corner. For undercounter installation, it
is recommended that the junction box be
located in the adjacent right or left cabinet. If
installing junction box on rear wall behind
oven, junction box must be recessed and
located in the upper or lower right or left corner
of cabinet.
Oven support surface MUST be solid, level and
flush with bottom of cabinet cutout.
Excessive
Microwave
Energy Exposure
Do not attempt to operate the
microwave
oven with the door open.
Do not tamper with or defeat the safety
interlocks.
Do not place objects
between the
microwave
oven front face and door.
Do not allow soim or cleaner residue to
accumulate
on sealing surface of the
microwave
oven door.
Do not operate the microwave
oven if
damaged.
Do not operate the microwave
oven if:
--
door is bent.
--
hinges and latches are broken or
loose.
--
door sea_s, sealing
surfaces or
glass are broken.
The microwave
oven door must close
properly
to provide
safe operation.
Have a qualified
repair person adjust,
repair and check microwave
oven for
microwave
leakage after a repair is
made.
Do not use microwave
for commercial
purposes.
The microwave
oven in this
unit is designed
for household
use
only.
Failure to foltow these instructions
could result in exposure
to excessive
microwave
energy.
It is the customer's responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is
adequate and in conformance with National
Electrical Code, ANSI/NFPA 70 _ latest
edition*, or CSA Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No. 0-M91 -
latest edition** and nit local codes and
ordinances.
Advertisement
