Related Manuals for ZyXEL Communications P-2304R-P1 Series
Summary of Contents for ZyXEL Communications P-2304R-P1 Series
- Page 1 P-2304R-P1 Series VoIP Station Gateway Quick Start Guide Version 3.60 Edition 1 10/2006...
- Page 2 P-2304R-P1 Series Quick Start Guide Overview This guide explains how to set up your P-2304R-P1 series device (“P-2304R-P1“) to make phone calls over the Internet. The following figure shows a typical way to use your P-2304R-P1. When you make a phone call over the Internet, you use one of your telephones (A) to dial the number. The telephones are connected to your P-2304R-P1 (C), which is connected to the broadband modem or router that provides Internet access (D).
-
Page 3: Hardware Connections
P-2304R-P1 Series Quick Start Guide 2 Hardware Connections 1 PHONE 1-4: Use a telephone cable (and any telephone adaptors provided with your P-2304R-P1) to connect your telephones to these ports. If you only have one telephone, you should only use one port. -
Page 4: Initial Configuration
P-2304R-P1 Series Quick Start Guide 3 Initial Configuration Use a web browser on your computer to set up your P-2304R-P1. See Troubleshooting if you have any problems. 3.1 Open the Wizard Setup Screen 1 Launch your web browser. 2 Enter http://192.168.1.1... -
Page 5: Connection Wizard
P-2304R-P1 Series Quick Start Guide 3.2 Connection Wizard If you subscribe to a Roadrunner service, you cannot use the Connection Wizard to set up your Internet connection. In this case, please see the User’s Guide for instructions. Note: You must have Internet account information before you can complete this section. - Page 6 P-2304R-P1 Series Quick Start Guide 3.2.1 Connection Wizard (Ethernet) Follow these steps if your ISP uses an Ethernet connection. 1 Click Next. 2 Select Get automatically from your ISP if your ISP did not give you a static IP address. Then, click Next, and go to step below.
- Page 7 P-2304R-P1 Series Quick Start Guide 3.2.2 Connection Wizard (PPP over Ethernet) Follow these steps if your ISP uses a PPP over Ethernet (PPPoE) connection. 1 Enter the information provided by your ISP. Use the 2 Select Get automatically from your ISP if your default values if your ISP did not provide the ISP did not give you an IP address.
-
Page 8: Voip Setup Wizard
P-2304R-P1 Series Quick Start Guide 3.3 VoIP Setup Wizard Note: You must have Internet access and a VoIP account before you can complete this section. 1 In the Wizard Setup screen, click VoIP Setup. 2 Enter the information provided by your VoIP service provider. -
Page 9: Bridge Mode
P-2304R-P1 Series Quick Start Guide 3 Wait while the P-2304R-P1 tries to register the 4 Click Finish. The PHONE light should be green. VoIP account(s). 3.4 Bandwidth Management Wizard (Optional) If you want to use the Bandwidth Management Wizard, please see the User’s Guide for instructions. -
Page 10: Phone Calls
P-2304R-P1 Series Quick Start Guide 4 Click Apply. The P-2304R-P1 automatically restarts. When the POWER light stops blinking and stays on, follow the directions in section to log in to the web configurator again. However, use the Management IP Address you set up in step 3, instead of http://192.168.1.1. -
Page 11: Troubleshooting
P-2304R-P1 Series Quick Start Guide Troubleshooting PROBLEM CORRECTIVE ACTION None of the lights turn Make sure that you are using the power adaptor provided with the P-2304R-P1. on when I plug in the Check all the connections you made in section 2. -
Page 12: Setting Up Your Computer's Ip Address
P-2304R-P1 Series Quick Start Guide PROBLEM CORRECTIVE ACTION There is no dial tone. Check the connection between your telephone and the P-2304R-P1. See section 2. Test the telephone wire. 1 Connect the wire to a telephone and a regular telephone outlet. - Page 13 P-2304R-P1 Series Quick Start Guide In Windows 2000/NT, click Network and Dial-up Connections. 3 Right-click on your network connection (for example, Local Area Connection). A menu appears, like the one shown here. 4 In the menu, click Properties. The network connection’s properties screen appears.