Table of Contents
Advertisement
Gas conversions (from Natural gas to L.P.gas; or from L.P.
gas to Natural gas} must be done by a qualified installer.
Fire Hazard
Shut off gas supply line valve.
Make all conversions before turning
gas supply
valve back on.
Failure to follow these instructions could result in
explosion, fire or other injury.
L.P.gas conversion
,,Complete installation sections A-C (Pages 7-8)
before converting cooktop to LID.gas. Check that main gas
supply line has been shut off and the power supply cord is
disconnected.
plastic
regulator
cover
LR
cap
--washer
--
Nat. gas
L.P. gas
DO NOT REMOVE THE PRESSUREREGULATOR.
[] Pressure regulator: Remove storage drawer and locate
pressure regulator at back of range. Remove plastic cover.
Turn cap marked "N" on front of pressure regulator counter-
clockwise with a wrench to remove. Do Not disturb or
remove the spring beneath the cap. Turn the cap over and
reinstall cap on regulator so that the letters "L.P." are visible.
Replace plastic cover over cap.
_U___
reinstall
orifice
_
one of the
[] Surface Burners:
spud
_
screws
Remove burner caps Use
....
\
\_j
.-_@_
s-ark
electrode
• .
"
ormce
---
a Phillips or Ouadrex
spud
/
screwdriver
to remove
holder'_._//_T_-
_\\\\\_\_\_
_/_
•
./- _\.,
_ _ f _/\_-_
the two screws holding the
_,
)) _.'_;,_
burner head down. Lift the
\_X,'_/_
__
burner head off the cooktop
\_
"/"\
to uncover the orifice spud
range cooktop
holder. The orifice spud is recessed in the holder.
Note: Reinstall one of the screws through the range cooktop
to hold orifice spud holder in place while removing and
replacing orifice spuds.
Locate the L.R gas orifice spuds in literature
package. Orifice spuds are stamped with a number
_-_,___
and marked with two color dots and a groove.
/,,_--_
5/16"
nut driver
groove
L.R gas
orifice
spud
orifice spud
Replace orifice
_
spud with the
_/_
number
listed
[(
_
in chart.
/_
"_orifice
number
burner
/
assembly
L.R Gas
Surface
Propane
Orifice
Color
burner
Rate (BTU/hr)
Number
Marking
Left rear
8,000
LB0
Green/Lt. Blue
Left front
11,000
L99
Green/Yellow
Right front
8,000
LB0
Green/Lt. Blue
Right rear
5,000
L65
Green/Brown
A brass orifice spud is located in the center of each burner
throat about 2" (5 cm) below the cooktop. Apply masking
tape to the end of a 5/16" nut driver to fit snugly over the
orifice spud. Press driver down onto the spud of the left
front burner and remove by turning spud counter-clockwise
and lifting it out. Replace the Natural gas spud with the
appropriate L.R gas spud shown in the table.
Continue to replace the remaining orifice spuds, one at a
time. Place the Natural gas spuds in plastic parts bag for
future use and keep with literature package. Replace burner
caps using both screws and burner grates.
hood
L.R gas
Natural
gas
_
decrease
increase
gas
gas
increase
decrease
flame
size
flame
size
for Natural
gas
,_11 orifice
hood
[] Oven burner: Use 1/2" combination wrench to
turn the orifice hood down snug onto pin (approximately 2
to 2-1/2 turns). DO NOT OVERTIGHTEN. The burner flame
cannot be properly adjusted if this conversion is not made.
Page 13
Advertisement
Table of Contents
