Safety Precautions - Haier HWM70-0528T User Manual

Safety precautions

Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
Earth
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or our customer care agent.
In case the washing machine is installed on ground
with carpet, do not block the ventilation hole with
carpet.
T h e v e n t i l a t i o n
holes at the bottom
Back
Soft object
Front
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
2
The washing machine must be positioned so that
the plug is accessible. Be sure to pull the plug off
and close the water faucet in following cases:
power failure, delivering the machine, setting the
machine idle or cleaning the machine. Do not plug
or pull the power plug with wet hand.
Do not use water hotter than 50 .
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not
breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.
Phenomena The reason
Buzzing upon reservation starts,
The top lid is not closed
the digitron displays "E0"
Is the drain hose put down?
No or slow drain, the digitron
displays "E1" , buzzing.
Is the drain hose blocked by
foreign material?
Running pauses during spin,
The top cover leaves open
the digitron displays "E2",
buzzing
Safety switch actuates, not Are the laundries put slantingly?
spin, (after self-correction
Is the machine slanting?
twice), the digitron displays
"E3", buzzing
The water tap is not open
No or slow water filling (not
The water inlet valve is blocked
reaching the level in 30 min),
The water pressure is too low
the digitron displays "E4",
and the current is too small
buzzing
The water level sensor is bad.
The digitron displays E6.
If the nozzle is choked with
Poor or no waterfall flow
foreign bodies
Is there power failure?
Is the power plug loose?
Not wash
Does the water level arrive at the
The machine does
set water level?
not act
Is the power plug loose?
Not spin
Is the top lid closed?
Are the laundries put orderly?
Is the machine slanting?
There's abnormal sound inside the
machine Are the laundries slanting in
spinning?
Is the jointer screw of the water
The water faucet leaks
inlet hose is loose or twisted
awry?
Common phenomena
Phenomena
The spinning is intermittent when it starts.
The wash procedure pauses.
Select spin program, but it does not work.
There may be some water flowing out of the
drain hose in the first use of the machine.
How to settle
Close the top lid
Put down the drain hose. Open
and close the top lid once.
Clean the foreign material.
Open and close the top lid once.
Close the top lid
Re-order the laundries. Close the
top lid.Level the machine in right
position.
Open and close the top lid once.
Open the water tap.
Push the "Start/Pause" button.
Clean the water inlet valve.
Push the "Start/Pause" button.
Wait for the normal water pressure
Before use.
Please contact the after-sales
service department.
Remove the foreign bodies
Use it when the power is on.
Insert the power plug tightly.
Affusion to the set water level.
Insert the power plug tightly.
Close the top lid
Put the laundries orderly.
Level the machine properly.
Re-order the laundries.
Fasten the jointer screw
properly.
Explanation
Balance the laundries to avoid slanting.
The cloth sensor is detecting , it will add water
after about 48 senconds.
The program is setting the drain time , certain
period is needed before it starts spinning.
It is the water remained performance inspection
by the factory.