Range Installation; Leveling The Range; Check Operation - Frigidaire PLCS389DCC Installation Instructions Manual

8. Range Installation
When unpacking the range, do not
discard the 4 shipping bolts. These are to be replaced
on the unit for use as leveling legs and height
adjustments.
Installation Without Side Panel(s)
A. The range cooktop overlaps the countertop at
the sides and the range rests on the floor. The
cooktop is 31 1/2" (81 cm) wide.
B. Install base cabinets 30" (76.2cm) apart. Make
sure they are plumb and level before attaching
cooktop. Shave raised countertop edge to clear
31 1/2" (81 cm) wide range top rim.
C. Install cabinet doors 31 " (78.7 cm) rain. apart so
as not to interfere with range door opening.
D. Cutout countertop exactly as shown on page 1.
E. A backguard kit can be ordered through your
dealer.
F. Adjust leveling legs so that the underside of the
cooktop is sitting on the countertop.
G. Level the range. The floor where the range
is to be installed must be level (see
Figure 11).
.
Installation For 29" Cutout Wide Opening
A. You must replace the actual side panels by new
and smaller side panels. These new side panels
can be ordered through a Service Center.
B. Follow instructions supply with your new side
panels to replace the actual side panels by the
new ones.
C. Check if the countertop is prepared for 29"
cutout wide opening in "Countertop
Preparation" section at p.6.
D. Install range as in the "Installation Without
Side Panels" section.
3. Installation With Backguard
The cutout depth of(21 3/4" (55.2 cm)Min., 22 1/8"
(56.2cm) Max.) needs to be increased to 24" (61 cm)
when installing a backguard.
4. Installation With End Panel
AEnd Panel kit can be ordered through aService
Center.
5. Installation With Full Side Panels
A Full Side Panels kit can be ordered through a Service
Center.
A. Install cabinet doors 31 " (78.7 cm) rain. apart so
as not to interfere with range door opening.
B. A backguard kit can be ordered through a
Service Center.
C. An end panel kit can be ordered through a
Service Center.
9. Leveling the Range
Level the range and set cooktop height before
installation in the cut-out opening.
1. Install an oven rack in the center of the oven.
2. Place a level on the
rack. Take 2 readings
with the level placed
diagonally in one
direction and then the
other. Level the
range, if necessary, by
adjusting the 4 leg
levelers with a wrench
(see Figure15).
3. Taking care to not Figure 11
damage the
countertop, slide range into cut-out opening and
double check for levelness. If the range is not
level, pull unit out and readjust leveling legs, or
make sure floor is level.
10. Check Operation
Refer to the Owner's Guide packaged with the range for
operating instructions and for care and cleaning of your
range.
Do not touch the elements or burners.
They may be hot enough to cause burns.
Remove all packaging from the oven before testing.
Install Burner Bases and Burner Caps
This range is equipped with sealed burners as shown
(see Figure 12).
A. Unpack burner bases Burner_ _--_/ _
and burner caps. Cap
B. Place burner bases
over each gas Burner
opening. Base
Gas
C. Make sure the Burner
burner is properly Pan _ Opening
aligned and leveled.
Place burner caps
over appropriate
burner bases.
NOTE: There are no burner
adjustments necessary on
this range.
2.
Figure 12
Turn on Electrical Power and Open Main Shutoff
Gas Valve
Check the Igniters
Operation of electric igniters should be checked after
range and supply line connectors have been carefully
checked for leaks and range has been connected to
electric power.