Moving The Appliance For Servicing And Cleaning; Range Installation - Frigidaire FGDS3065PF Installation Instructions Manual

30" DUAL FUEL SLIDE-IN RANGE INSTALLATION INSTRUCTIONS
8
Moving the Appliance for
Servicing and Cleaning
Turn off the range line fuse or circuit breakers at the main
power source, and turn off the manual gas shut-off valve.
Make sure the range is cold. Remove the service drawer
(warmer drawer on some models) and open the oven door.
Lift the range at the front and slide it out of the cut-out
opening without creating undue strain on the flexible gas
conduit. Make sure not to pinch the flexible gas conduit at
the back of the range when replacing the unit into the cut-
out opening. Replace the drawer, close the door and switch
on the electrical power and gas to the range.
9

Range Installation

Important Note: Door removal is not a requirement for
installation of the range, but is an added convenience.
Refer to the Use
and Care Guide for
oven door removal
instructions.
9.1
The range cooktop overlaps the countertop at
the sides and the range rests on the floor. The
cooktop is 31 1/2" (80 cm) wide.
9.2
Install base cabinets 30" (76,2 cm) apart. Make
sure they are plumb and level before attaching
cooktop. Shave raised countertop edge to clear
31 1/2" (80 cm) wide range top rim.
9.3
Install cabinet doors 31" (78,7 cm) min. apart so it
will not interfere with range door opening.
9.4
Cutout countertop exactly as shown on page 3.
For models equipped with Leveling Device:
9.5
Make sure the front leveling legs and the rear
leveling device are setup higher than the height of
the cabinet.
9.6
Install the anti-tip bracket
at this point before placing the range at its
final position. Follow the installation instructions
on page 16 or on the anti-tip bracket template
supplied with the range.
9.7
To provide an optimum installation, the top surface
of the countertop must be level and flat (lie on the
same plane) around the 3 sides that are adjacent
to range cooktop. Proper adjustments to make
the top flat should be made or gaps between the
countertop and the range cooktop may occur.
(Models with an Electric Oven and a Gas Cooktop)
Figure 12
9.8
your appliance, do not handle or manipulate it by the
cooktop or control console. Manipulate with care.
9.9
Position range in front of the cabinet opening.
9.10
Make sure that the cooktop which overhangs the
countertop clears the countertop. If necessary,
raise the unit by lowering the leveling legs.
9.11
Slide the range into the cutout opening and center
it before leveling it.
9.12
Level the range (see section 10). The floor where
the range is to be installed must be level. Follow
the instructions under "Leveling the Range-
Models Equipped with Leveling Device".
9.13
Adjust leveling legs so that the underside of the
cooktop is sitting on the countertop. Carefully
screw in (refer to Leveling the range: Models
equipped with Leveling Device") the back leveling
leg until the cooktop overhang touches slightly the
countertop. Then carefully screw in the front two
leveling legs until the cooktop overhang touches
slightly the countertop.
For models equipped with Leveling Leg
only (no leveling device):
9.5
Make sure the four leveling legs (front and rear)
are setup higher than the height of the cabinet.
9.6
at this point before placing the range at its
final position. Follow the installation instructions
on page 17 or on the anti-tip bracket template
supplied with the range.
9.7
To provide an optimum installation, the top surface
of the countertop must be level and flat (lie on the
same plane) around the 3 sides that are adjacent
to range cooktop. Proper adjustments to make
the top flat should be made or gaps between the
countertop and the range cooktop may occur.
9.8
your appliance, do not handle or manipulate it by
the cooktop. Manipulate with care.
9.9
Position range in front of the cabinet opening.
9.10
Make sure that the cooktop which overhangs the
countertop clears the countertop. If necessary,
raise the unit by lowering the leveling legs.
9.11
Level the range (see section 10). The floor where
the range is to be installed must be level. Follow
the instructions under "Leveling the Range-Models
Equipped with Leveling Legs".
9.12
Slide the range into the cutout opening.
11
To reduce the risk of damaging
Install the anti-tip bracket
To reduce the risk of damaging