Dmx Protocol - Martin MAC 101 User Manual

DMX protocol

Note: DMX values labeled "No function" will have no effect - the last functional value will be used.
RAW
In mode, RGB output is uncalibrated. In
Raw, RGB
1
2
3
4
5
6
7
Basic DMX Value
0 - 19
20 - 49
50 - 64
65 - 69
70 - 84
85 - 89
90 - 104
105 - 109
110 - 124
125 - 129
1
130 - 144
145 - 149
150 - 164
165 - 169
170 - 184
185 - 189
190 - 204
205 - 209
210 - 224
225 - 229
230 - 244
245 - 255
2
0 - 255
3
0 - 255
4
0 - 255
5
0 - 255
6
0 - 255
0 - 9
10 - 14
15 - 39
40 - 44
45 - 49
50 - 54
55 - 59
60 - 64
65 - 69
70 - 74
75 - 89
90 - 94
7
95 - 99
100 - 104
105 - 249
250 - 255
RGB
mode, output is calibrated.
Percent Function
Electronic shutter effect
0 - 7 Shutter closed
8 - 19 Shutter open
Strobe 1 (fast → slow)
20 - 25
26 - 27 Shutter open
Strobe 2: opening pulse (fast → slow)
28 - 33
34 - 35 Shutter open
Strobe 3: closing pulse (fast → slow)
36 - 41
42 - 43 Shutter open
Strobe 4: random strobe (fast → slow)
44 - 49
50 - 51 Shutter open
Strobe 5: random opening pulse (fast → slow)
52 - 57
58 - 59 Shutter open
Strobe 6: random closing pulse (fast → slow)
60 - 65
66 - 67 Shutter open
Strobe 7: burst pulse (fast → slow)
68 - 73
74 - 75 Shutter open
Strobe 8: random burst pulse (fast → slow)
76 - 81
82 - 83 Shutter open
Strobe 9: sine wave (fast → slow)
84 - 89
90 - 91 Shutter open
Strobe 10: burst (fast → slow)
92 - 97
98 - 100 Shutter open
Dimmer
Closed → open
0 - 100
Pan
0 - 100 Pan 0 - 430°
Pan fine
0 - 100 Pan fine (Least Significant Byte)
Tilt
0 - 100 Tilt 0 - 300°
Tilt fine
0 - 100 Tilt fine (Least Significant Byte)
Fixture control settings
0 - 1 No function
2 - 3 Reset entire fixture
4 - 13 No function
14 - 15 PTSP = NORM
2
16 - 17 PTSP = FAST
18 - 19 PTSP = SLOW
20 - 21 No function
22 - 23 Fan mode FULL
24 - 25 No function
26 - 27
Fan mode REGULATED
28 - 33
No function
34 - 35
RGB control mode (calibrated RGB)
36 - 37
No function
38 - 39
RAW control mode (uncalibrated RGB)
40 - 97
No function
98 - 100
Illuminate display
1
If DMX Reset is disabled in the menu, a reset command can
only be executed if channel 2 is set to 232 and channel 1 is set
to zero. These values need to be held for 5 seconds before
feature is activated. Values must be "snapped to" to function.
2
Menu override: setting unaffected by power off/on.
3
Value must be held for 3 seconds to activate. Setting
unaffected by power off/on.
Table 2: DMX Protocol
DMX protocol
1
2
2
2
2
3
3
21