Jenn-Air JXT8136ADS Installation Manual
35-3/8"(90 cm); 42" range hood
Hide thumbs
Also See for JXT8136ADS:
- Installation manual (30 pages) ,
- User manual (27 pages) ,
- Service (34 pages)
Advertisement
Table of Contents
RANGE
Modal
Numbe r:
JXT8136ADS
] XT8142ADS
Manufacturer
Number:
S98M9@B
$98E42S
Size'.
35-3/8"
_90 cm_
42"
GUIDE
TABLE OF CONTENTS
Safet, Instructions ....................................................
1
List of Materials .......................................................
2
Heights ....................................................
3
Ducting ....................................................................
4
...........................................................
5
In sta 11 a ti on ............................................................
b-8
Form No. A/04/03
Part No. IS9800-0303A
¢)2004
May{ag
Appliances
Sales (o.
litho
U.S.A.
Advertisement
Table of Contents
Related Manuals for Jenn-Air JXT8136ADS
Summary of Contents for Jenn-Air JXT8136ADS
-
Page 1: Table Of Contents
RANGE Modal Numbe r: JXT8136ADS ] XT8142ADS Manufacturer Number: S98M9@B $98E42S Size'. 35-3/8" _90 cm_ 42" GUIDE TABLE OF CONTENTS Safet, Instructions ............ List of Materials ............Mounting Heights ............ Ducting ..............Specifications ............In sta 11 a ti on ............ - Page 2 MODEL: JXT8136ADS JXT8142ADS Installation Theinstallation in this manuar i s intended f or qualifiedinstarlers, s ervicetechnicians or persons with similarquarified background, DONOT attemptto instarl t his appriance yourserf, h iury courd resultfrom installingthe unitdue to rackof appropriate erectricar a nd technicar b ackground, Air erectricar wiring must be prope@ installed, insulated and grounded.
-
Page 3: List Of Materials
LiST OF MATERIALS 1 - Hood Body 1 - Duct CoverAssemNy (2 pieces) 1 - Parts Bag: 1 - Duct Cover Mounting Bracket 2 - Mounting Brackets Packet of Mounting Screws 2 - Metallic Filters 1 - Metallic Bitterfly Damper NO DUCTING iS iNCLUDED... -
Page 4: Mounting Heights
MOUNTINGHEIGHTS & CLEARANCE Minimum mounting height betweenrangetop to hood bottom shouldbe no less than 24": Maximum mounting heightshould be no higher than 32". 29"-4&65" It is importantto install the hoodat the proper mountingheight. Hoodsmounted too low could result in heat damageand fire hazard; while hoodsmountedtoo high will be hard to reach and will lose performanceand efficiency. - Page 5 DUCTJNG NEVER exhaust air or terminate duct work into spaces between walls, crawr spaces, ceiling,attics or garages. Air exhaust must be ducted to the outside. UseMetal ductwork only. FastenaHconnections with sheet metal screws and tape aHjoints w/certified SHyerTape or DuctTape. Some Ducting Options: RoofPitchw/ Flashing&...
-
Page 6: Specifications
SPECIFICATIONS ELECTRICAL All Ebctrbal work must by performed by qualified ebctrbian or person with similar technbal know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow National ebctrbal codes or prevailing local codes and ordinances. -
Page 7: In Sta 11 A Ti On
INSTALLATION Dimensionsof Support Arms 2325" .rear AddBlockings Support Arms with Tabs position FastenCeiling Plate Mounting the RangeHood 1. Add and secure Nockings (minimum 2x4 studs) onto ceiling joist. 2. Center,mark and fasten Ceiling Hate onto ceiling /" where hood is to be hung. Make sure front of bracket is facing as shown on diagram. - Page 8 INSTALLATION Iockingtabs Mounting the RangeHood 8. Lift canopy and snap rocking tabs into Nower unit. 9. Fasten canopy to Nower with screw pro vided from inside of canopy. 10. Pushterescopic duct section up in prace and fasten. Note: Butterfry damper may be installed by pracing it ontop of the motor housing.
- Page 9 Carbon Filters help to purify fumes exhausted from cooking for re-circulation. CarbonFilters (Required) 1. Purchase ductlessCarbonFiltersas follows: Hood Model: Part No. Filters in pkg. JXT8136ADS JFLTRCS036 JXT8142ADS JFLTRCS036 2. Remove meta! filters on hood. Clip carbon filters onto each slot opening. 3. Re-install metal filters.
Need help?
Do you have a question about the JXT8136ADS and is the answer not in the manual?
Questions and answers