Advertisement

Service
This manual is to be used by qualified appliance
technicians only. Maytag does not assume any
responsibility for property damage or personal
injury for improper service procedures done by
an unqualified person.
Vent Hoods
This Base Manual covers general information
Refer to individual Technical Sheet
for information on specific models
This manual includes, but is
not limited to the following:
JXT5830ADB/W/S
JXT5836ADB/W/S
JXT6030ADS
JXT6036ADS
JXT8030ADS
JXT8036ADS
JXT8042ADS
JXT8136ADS
JXT8142ADS
JXT9030CDP
JXT9036CDP
JXT9048CDP
JXT9130CDP
JXT9136CDP
16023510
November 2004
©
2004 Maytag Services

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JXT5830ADB and is the answer not in the manual?

Questions and answers

Summary of Contents for Jenn-Air JXT5830ADB

  • Page 1 Refer to individual Technical Sheet injury for improper service procedures done by an unqualified person. for information on specific models This manual includes, but is not limited to the following: Vent Hoods JXT5830ADB/W/S JXT5836ADB/W/S JXT6030ADS JXT6036ADS JXT8030ADS JXT8036ADS JXT8042ADS JXT8136ADS...
  • Page 2: Important Information

    Important Information Pride and workmanship go into every product to provide our customers with quality products. It is possible, however, that during its lifetime a product may require service. Products should be serviced only by a qualified service technician who is familiar with the safety procedures required in the repair and who is equipped with the proper tools, parts, testing instruments and the appropriate service information.
  • Page 3: Table Of Contents

    Table of Contents Important Information ............ 2 Disassembly Procedures for Models JXT9030CDP, Important Safety Information JXT9036CDP, JXT9048CDP, JXT9130CDP, JXT9136CDP In Case of Fire ............4 Halogen Light Removal ..........13 Safety Practices for Servicer ........4 Heat Lamp Removal ..........13 Servicing ..............
  • Page 4: Important Safety Information

    Important Safety Information Recognize this symbol as a safety precaution. W A R NIN G In Case of Fire Fires can occur as a result of over cooking or excessive WARNING grease. Though a fire is unlikely, proceed as follows: If the information in this manual is not followed exactly, Surface Element Fires a fire or explosion may result causing property...
  • Page 5: Electrical Requirements

    Important Safety Information Precautions Electrical Requirements • When cutting or drilling into walls or ceilings, do not 120-volt, 60 Hertz, 40 amp, individual circuit which is damage electrical wiring and other hidden utilitites. properly grounded, polarized and protected by a circuit •...
  • Page 6: General Information

    Brushed Chrome Amana Traditional White Magic Chef Traditional Almond Graffer & Prostyle Sattler Monochromatic Bisque Hardwick Stainless Jenn-Air Traditional Bisque Maytag W White on White Norge Frost White (True Color White) Universal Natural Bisque (True Color Bisque) Crosley Listing Fuel...
  • Page 7: Specifications

    Complete enclosed registration card and promptly return. hood shroud. If registration card is missing: • For Jenn-Air product call 1-800-688-1100 or visit the Web Site at www.jennair.com • For product in Canada call 1-866-587-2002 or visit the Web Site at www.jennair.com When contacting provide product information located on rating plate.
  • Page 8: Vent Hood Description

    Range Description Vent Hood Description Filters/Filter Covers Touch Pad/Control Pad Halogen Lights Blower Motor Heat Lamps Touch Pad/Control Pad Halogen Lights Blower Motor Filters/Filter Covers (in vent hood) (in vent hood) 16023510 ©2004 Maytag Services...
  • Page 9: Troubleshooting Procedures

    Troubleshooting Procedures W ARNING To avoid risk of electrical shock, personal injury, or death, disconnect power to vent hood before servicing, unless testing requires power. Problem Possible Cause Correction • Verify 120 VAC is present at unit. Blower motor will not No input power ..........
  • Page 10 Troubleshooting Procedures W ARNING To avoid risk of electrical shock, personal injury, or death, disconnect power to vent hood before servicing, unless testing requires power. Problem Possible Cause Correction • Verify wires are connected and Lights illuminate at half Loose wires to lights/control board....brightness only tight at light socket/control board.
  • Page 11: Testing Procedures

    Testing Procedures WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to vent hood before servicing, unless testing requires power. Model Numbers Component Test Procedure Results Halogen lights Press light switch once ......... Lights illuminate to full brightness (120 VAC).
  • Page 12 Testing Procedures WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to vent hood before servicing, unless testing requires power. Model Numbers Component Test Procedure Results JXT8030ADS, Blower Motor Check input voltage by placing leads on JXT8036ADS, screws in green connector, black wire JXT8042ADS,...
  • Page 13: Disassembly Procedures For Models Jxt9030Cdp

    Disassembly Procedures To avoid risk of electrical shock, personal injury or WARNING death; disconnect power to unit before servicing. Disassembly for models JXT9030CDP, JXT9036CDP, JXT9048CDP, JXT9130CDP, JXT9136CDP Halogen Light Removal Halogen Light Socket Removal 1. Disconnect power to vent hood. 1.
  • Page 14: Light Panel Removal

    Disassembly Procedures To avoid risk of electrical shock, personal injury or WARNING death; disconnect power to unit before servicing. Light Panel Removal 1. Disconnect power to vent hood. 2. Remove grease filters and covers, see "Grease Filter/ Grease Filter Cover Removal" procedure. 3.
  • Page 15: Transformer Removal

    Disassembly Procedures To avoid risk of electrical shock, personal injury or WARNING death; disconnect power to unit before servicing. Transformer Removal 1. Disconnect power to vent hood. 2. Remove grease filters by using handles and pulling filter toward the rear of the vent hood. 3.
  • Page 16: Disassembly Procedures For Models Jxt8042Ads

    Disassembly Procedures To avoid risk of electrical shock, personal injury or WARNING death; disconnect power to unit before servicing. Disassembly for models JXT8042ADS, JXT8142ADS, JXT5830AD*, JXT5836AD* Grease Filter/Grease Filter Cover Removal Halogen Light Removal 1. Turn off power to the blower motors. 1.
  • Page 17: Control Panel Removal

    Disassembly Procedures To avoid risk of electrical shock, personal injury or WARNING death; disconnect power to unit before servicing. 10. Label and disconnect blower electrical connections Control Panel Removal and remove blower motor. 1. Disconnect power to vent hood. 11. Reverse procedure to reinstall blower motor. 2.
  • Page 18 Appendix A A – 1 16023510 ©2004 Maytag Services...
  • Page 19: Appendix A: Installation Instructions

    Installation Instructions (JXT5830AD*, JXT5836AD*) ©2004 Maytag Services 16023510 A – 2...
  • Page 20 Installation Instructions (JXT5830AD*, JXT5836AD*) A – 3 16023510 ©2004 Maytag Services...
  • Page 21: Jxt8030Ads, Jxt8036Ads, Jxt8048Ads

    Installation Instructions (JXT8030ADS, JXT8036ADS, JXT8042ADS) ©2004 Maytag Services 16023510 A – 4...
  • Page 22 Installation Instructions (JXT8030ADS, JXT8036ADS, JXT8042ADS) A – 5 16023510 ©2004 Maytag Services...
  • Page 23: Jxt8136Ads, Jxt8142Ads

    Installation Instructions (JXT8136ADS, JXT8142ADS) ©2004 Maytag Services 16023510 A – 6...
  • Page 24 Installation Instructions (JXT8136ADS, JXT8142ADS) A – 7 16023510 ©2004 Maytag Services...
  • Page 25: Jxt9030Cdp, Jxt9036Cdp, Jxt9048Cdp

    Installation Instructions (JXT9030CDP, JXT9036CDP, JXT9048CDP) ©2004 Maytag Services 16023510 A – 8...
  • Page 26 Installation Instructions (JXT9030CDP, JXT9036CDP, JXT9048CDP) A – 9 16023510 ©2004 Maytag Services...
  • Page 27: Jxt9130Cdp, Jxt9136Cdp

    Installation Instructions (JXT9130CDP, JXT9136CDP) ©2004 Maytag Services 16023510 A – 10...
  • Page 28: Jxt9130Cdp, Jxt9136Cdp

    Installation Instructions (JXT9130CDP, JXT9136CDP) A – 11 16023510 ©2004 Maytag Services...
  • Page 29 Appendix B ©2004 Maytag Services 16023510 B – 1...
  • Page 30 Use Information (JXT583*AD*, JXT803*ADS,JXT8042ADS, JXT8136ADS, JXT8142ADS) B – 2 16023510 ©2004 Maytag Services...
  • Page 31 Use Information (JXT583*AD*, JXT803*ADS, JXT8042ADS, JXT8136ADS, JXT8142ADS) ©2004 Maytag Services 16023510 B – 3...
  • Page 32 Use Information (JXT583*AD*, JXT803*ADS, JXT8042ADS, JXT8136ADS, JXT8142ADS) B – 4 16023510 ©2004 Maytag Services...
  • Page 33 Use Information (JXT903*CDP, JXT9048CDP, JXT913*CDP) ©2004 Maytag Services 16023510 B – 5...
  • Page 34: Care And Cleaning

    Care and Cleaning (all) B – 6 16023510 ©2004 Maytag Services...

Table of Contents