Yealink SIP-T18P User Manual
Yealink phones
Hide thumbs
Also See for SIP-T18P:
- User manual (50 pages) ,
- Quick install manual (2 pages) ,
- Quick reference (2 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Yealink SIP-T18P
Summary of Contents for Yealink SIP-T18P
- Page 1 Yealink Phones User Guide © 2003 - 2012 Bicom Systems...
-
Page 2: Table Of Contents
............................13 DNS SRV ..............................14 Part V Configure BLF 1 Extension Settings ........................... 16 2 Phone Settings ........................... 16 Part VI Shared Parking 1 Extension Settings ........................... 17 2 PBXware Settings ........................... 18 © 2003 - 2012 Bicom Systems... -
Page 3: Part I Introduction
Introduction Yealink Phones User Guide This User Guide is written as general guide on how to set up the Yealink phone models: SIP-T18P, SIP-T20P, SIP-T22P, SIP-T26P, SIP-T28P, SIP-T60P and SIP-T65P to work with PBXware 3.1. Requirements 1. Identify Yealink Phone Model To start and successfully complete registration of your Yealink phone you need to know which phone model you will setup. -
Page 4: Part Iii Installation
"Release" denotes the exact version of your PBXware. Installation This chapter describes how to install and connect the phone to the electrical power and data network as well as how to apply factory settings. The following topics are covered: Power adapter © 2003 - 2012 Bicom Systems... -
Page 5: Power Adapter
For Yealink phone models SIP-T20P, SIP-T22P, SIP-T26P, SIP-T28P, SIP-T60P and SIP-T65P on the phone keyboard press Menu then Enter button to see the phone IP address on the display. For the Yealink phone model SIP-T18P pickup the handset and dial **90#. -
Page 6: Part Iv Registering Phone
Open a new browser window and enter the IP address in order to access the PBXware web administration login screen. Example: http://192.168.1.10. Login to PBXware with your e-mail address and password. 2. UAD settings Navigate to Settings:UAD. © 2003 - 2012 Bicom Systems... - Page 7 Select Yealink phone model from the UAD select box. Select Location: Local or Remote. Local is for all extensions registered on the LAN and Remote is for all extensions registered from remote networks, WAN, Internet etc. © 2003 - 2012 Bicom Systems...
-
Page 8: Hostname Or Ip Address
Click on the Save button. 4.1.3 Registering Phone This chapter describes how to register Yealink phone using Hostname or IP Address, or DNS SRV. The following topics are covered: Hostname or IP Address DNS SRV © 2003 - 2012 Bicom Systems... - Page 9 PBXware. N O TE Y our DNS Serv er needs to be configured correctly for this to work. Bicom Sy stem s can prov ide serv ice to set up this for y ou. © 2003 - 2012 Bicom Systems...
- Page 10 Make sure DNS server is configured to automatically route registration request to a PBXware which is actually under another domain name, example: newbicomsystems.com. Transport Select DNS SRV from the drop down menu. Click on the Confirm button. © 2003 - 2012 Bicom Systems...
-
Page 11: Auto Provisioning
Make sure Yealink UAD is enabled. To check the UAD status click on the edit icon corresponding to your Yealink phone. Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes. © 2003 - 2012 Bicom Systems... -
Page 12: Creating Extension
Local is for all extensions registered on the LAN and Remote is for all extensions registered from remote networks, WAN, Internet etc. Click on the Next step button. 2. Extension values Enter values into the required field text boxes. REQUIRED FIELDS © 2003 - 2012 Bicom Systems... -
Page 13: Registering Phone
Click on the Save button. 4.2.3 Registering Phone This chapter describes how to register Yealink phone using DHCP, TFTP, HTTP & HTTPS or DNS SRV. The following topics are covered: DHCP TFTP or HTTP & HTTPS DNS SRV © 2003 - 2012 Bicom Systems... -
Page 14: Tftp
Click on Upgrade tab. Click on Advanced tab. You can use TFTP or HTTP & HTTPS protocols in order to Auto Provision your Yealink phone. Choose which protocol you want to use: TFTP HTTP & HTTPS © 2003 - 2012 Bicom Systems... - Page 15 Make sure you replace Hostname or IP Address from this example with your PBXware Hostname or IP address. Check New Config Select Power on + Repeatedly. Click on the Confirm button. You'll have to wait sometime prior for the device to save changes. © 2003 - 2012 Bicom Systems...
-
Page 16: Dns Srv
If there is no DHCP in your network, you can still auto provision your Yealink phone. Please refer to your Yealink phone model User Guide for instruction about setting static IP address. After you configure your Yealink phone to use a static IP address, continue with the following steps. © 2003 - 2012 Bicom Systems... -
Page 17: Part V Configure Blf
This chapter describes how to configure BLF (Busy Lamp Field) for Yealink phones. N O TE BLF (Busy Lam p Field) supported only with Y ealink phone m odel SIP-T 26P and SIP-T 28P. The following topics are covered: © 2003 - 2012 Bicom Systems... -
Page 18: Extension Settings
Click on Save button. Phone Settings 1. Login to phone web administration interface Open a new browser window and enter your phone IP address in order to access the phone web administration interface login screen. Example: http://192.168.1.22. © 2003 - 2012 Bicom Systems... -
Page 19: Part Vi Shared Parking
On the Extensions page click on the edit icon corresponding to your extension. Click on Advanced Options button. Navigate down to the Auto Provisioning and Presence group of settings. Make sure Auto Provisioning is set to Yes. © 2003 - 2012 Bicom Systems... -
Page 20: Pbxware Settings
Copy and past below code at the bottom of extensions.conf file. [hints] exten => 701,hint,park:701@parkedcalls exten => 702,hint,park:702@parkedcalls exten => 703,hint,park:703@parkedcalls exten => 704,hint,park:704@parkedcalls exten => 705,hint,park:705@parkedcalls exten => 706,hint,park:706@parkedcalls exten => 707,hint,park:707@parkedcalls exten => 708,hint,park:708@parkedcalls © 2003 - 2012 Bicom Systems... - Page 21 Shared Parking exten => 709,hint,park:709@parkedcalls exten => 710,hint,park:710@parkedcalls 4. Click on the Save button to save changes. 5. Click on the Reload button top right in order to reload PBXware for changes to take effect. © 2003 - 2012 Bicom Systems...