Table of Contents
Advertisement
6
Refer to Figures 9 and 10.
DESCRIPTION
The POWERTEC Oscillating Spindle Sander makes
sanding irregular shapes and curves in wood easy and
convenient.
Sander features a large 18" cast iron table, dust port and
onboard storage of durms, inserts and washers.
Six sizes of drums are included.
SPECIFICATIONS
Spindle diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ½"
Drum diameters. . . . . . . . . . . . . ½", ¾", 1", 1½", 2" and 3"
Drum length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4½"
Spindle stroke. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1"
Spindle oscillation . . . . . . . . . . . . . . . . . . . . . . . . . 30 SPM
Spindle speed . . . . . . . . . . . . . . . . . . . . . . . . . . 1725 RPM
Table diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18"
Table height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15½"
Dust port diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2"
Base dimensions . . . . . . . . . . . . . . . . . . . . . . 22½" x 16½"
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 lbs
WARNING
Operation of any power tool can result in foreign objects
being thrown into the eyes, which can result in severe
eye damage. Always wear safety goggles complying with
United States ANSI Z87.1 (shown on package) before
commencing power tool operation.
CAUTION: Always observe following safety precautions.
SAFETY PRECAUTIONS
• When adjusting or replacing any parts on the tool, turn
switch OFF and unplug the power cord.
• Make sure all moving parts are free and clear of any
interference.
• Make sure all guards are properly attached and
fastened in position.
• Make sure all fasteners are tight and have not vibrated
loose.
• Always wear eye protection or face shield.
• Test operation by hands for clearance and adjust if
necessary. Do this only when the power is off.
• The drum should trun clockwise.
• Allow drum to come up to full speed before starting
sanding.
• Do not attemp to stall motor or reduce speed. Do not
force the work into the abrasives.
• Keep your hands clear of any moving parts.
• Avoid kickback of the workpiece by sanding in
accordance with the directional arrows.
• Never push a sharp object rapidly against sleeve.
Abrasive backing may be damaged.
• Never use the machine for wet sanding, which can
result in hazard of electrical shock.
OPERATION
• Make sure workpiece is well supported by table during
operation.
• Replace abrasives when they become worn or glazed.
ON/OFF SWITCH
Refer to Figure 9.
The ON/OFF switch is located on the sander base. To
turn the sander ON, pull the switch to the up
position. To turn the sander OFF, push the switch to the
down position.
NOTE: when the machine is not in use, the switch should
be locked in the "OFF" position to prevent unauthorized
use.
• To lock the machine, turn the switch to "OFF" position.
Pull the key out. The switch can't be turned on without
the key.
• If the key is removed when the switch is at the "ON"
position, the switch can be turned off but can not be
turned on again.
• To unlock, place the key into the slot on switch unit until
it snaps.
Figure 9 - Locking Switch in OFF Position
Advertisement
Table of Contents
