PowerTec HS1002 Owner's Manual
  1. Manuals
  2. Brands
  3. PowerTec Manuals
  4. Sander
  5. HS1002
  6. Owner's manual

PowerTec HS1002 Owner's Manual

1/2 sheet sander
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Owner's Manual
1/2 Sheet Sander
QUESTION...
1•847•780•6120
Visit us on the web at www.southerntechllc.com
You will need this manual for safety instructions, operating procedures, and warranty.
Put it and the original sales invoice in a safe, dry place for future reference.
Model No. HS1002
16-0705

Advertisement

Table of Contents
loading

Related Manuals for PowerTec HS1002

Summary of Contents for PowerTec HS1002

  • Page 1 Model No. HS1002 Owner’s Manual 1/2 Sheet Sander QUESTION... 1•847•780•6120 Visit us on the web at www.southerntechllc.com You will need this manual for safety instructions, operating procedures, and warranty. Put it and the original sales invoice in a safe, dry place for future reference.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS PRODUCT SPECIFICATIONS SECTION PAGE SAFETY RULES Voltage ........120V Hertz .
  • Page 3 GENERAL SAFETY RULES • Avoid body contact with grounded surfaces. There WARNING is an increased risk of electrical shock if the body is For your own safety, read and understand all warnings grounded. • Use the proper extension cord. Make sure your and operating instructions before using any tool or extension cord is in good condition.

  • Page 4: Safety Rules

    SPECIFIC SAFETY RULES FOR SANDER Be aware of general power tool safety. Make sure all the • Empty dust collection box often. Dispose of coated dust safety rules are understood. particles (such as resin, polyurethane, varnish, shellac, etc.) according to finish manufacturer's guidelines. •...

  • Page 5: Attaching Dust Collection Box

    • Raise the rear paper clamp up and away from the tab NOTE: To remove the non-adhesive sandpaper, raise the on the sander's base. This will release the rear paper front and rear paper clamps up and away from the tabs on clamp.

  • Page 6: Double Insulation

    Running at a lower voltage will damage when servicing. the motor. OPERATION SANDING Your Powertec sander is designed and engineered to sand wood, plastic, metal, filler and painted surfaces. Sandpaper Selection SWITCHING ON AND OFF • Choose the correct grit and type of sandpaper for the job.

  • Page 7: Maintenance

    MAINTENANCE • Remove the filter. WARNING • To clean filter tap it on the side of a trash receptacle or Any attempt to repair or replace electrical parts on this blow it with compressed air. tool may be hazardous. Repairs not listed here should be Figure 7 performed by a qualified service technician.

  • Page 8: Parts Illustration

    SANDER PARTS ILLUSTRATION...
  • Page 9 SANDER PARTS LIST No. Part No. Description Qty Specification No. Part No. Description Qty Specification HS1002001 Left housing PA6-GF30 HS1002026 Bearing holder PA6-GF30 HS1002002 Cord guard HS1002027 Speed regulator HS1002003 Cord clip HS1002028 Clamping wire 65Mn HS1002004 Screw ST4*13 HS1002029 Vibration foot HS1002005 O-ring...

  • Page 10: Warranty

    30- DAY SATISFACTION GUARANTEE POLICY During the first 30 days after the date of purchase, if you are dissatisfied with the performance of this POWERTEC tool for any reason, you may return the tool to the retailer from which it was purchased for a full refund or exchange. You must present proof of purchase and return all original equipment packaged with the original product.
  • Page 11 NOTE...
  • Page 12 Southern Technologies, LLC 3816 Hawthorn CT, Waukegan, IL 60087...

Table of Contents