1. Manuals
  2. Brands
  3. PowerTec Manuals
  4. Sander
  5. BD6900
  6. Owner's manual

PowerTec BD6900 Owner's Manual

6" x 9" woodworking belt disc sander
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Owner's Manual
6" x 9" Woodworking Belt Disc Sander
QUESTION...
1•877•393•7121
Visit us on the web at www.southerntechllc.com
You will need this manual for safety instructions, operating procedures, and warranty.
Put it and the original sales invoice in a safe, dry place for future reference.
Model No. BD6900
11-0615

Advertisement

Table of Contents
loading

Related Manuals for PowerTec BD6900

Summary of Contents for PowerTec BD6900

  • Page 1 Model No. BD6900 Owner’s Manual 6" x 9" Woodworking Belt Disc Sander QUESTION... 1•877•393•7121 Visit us on the web at www.southerntechllc.com You will need this manual for safety instructions, operating procedures, and warranty. Put it and the original sales invoice in a safe, dry place for future reference.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS PRODUCTION SPECIFICATIONS SECTION PAGE PREPARATION Horsepower (Peak HP)..........1.2 Voltage................120 Work Preparation Amp................7.5 Work Area Preparation Tool Maintenance Hertz................60 Tool Operation Phase.................Single RPM................3450 ASSEMBLY Belt size..............6 x 48" Unpackaging Belt speed............2400 FPM Tool Needed Disc diameter..............9" Mount Sander Attach Abrasive Disc Disc speed............3100 RPM Attach Table...

  • Page 3: Preparation

    • Keep visitors at a safe distance from work area. • Keep children out of the work area. Ensure your work Your Powertec belt/disc sander is designed and shop is child-proof. Use padlocks, master switches or engineered to sand wood or wood products. Sanding of...

  • Page 4: Assembly

    CAUTION Think safety! Safety is a combination of operator common sense and alertness at all times when tool is being used. WARNING Do not attempt to operate tool until it is completely assembled according to the instructions. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE ASSEMBLY UNPACKING...

  • Page 5: Mount Sander

    MOUNT SANDER Figure 3 1. Choose a suitable location to mount the sander. The sander must be installed in a place with ample lighting and correct power supply. To install sander: 2. The sander must be bolted to a firm, level surface. 3.

  • Page 6: Operation5

    POWER SOURCE cord or plug is necessary, do not connect the green (or green and yellow) wire to a live terminal. WARNING EXTENSION CORDS Do not connect sander to the power source until • The use of any extension cord will cause some drop in all assembly steps have been completed.

  • Page 7: Basic Sander Operations

    OPERATION BASIC SANDER OPERATIONS ON/OFF Switch (Fig. 8) The keyed switch is intended to prevent unauthorized use Figure 9 of the sander. 1. To turn the sander ON insert the yellow key (1) into the key slot in the center of the switch. 2.

  • Page 8: Adjusting Belt Tracking

    ABRASIVE DISC SANDING 1. Abrasive disc sanding is well suited for finishing small Figure 11 flat surfaces and convex edges. 2. Move workpiece across down side (left) of abrasive disc. Hold workpiece firmly with both hands; keep fingers away from abrasive disc. 3.

  • Page 9: Replacing Abrasive Disc

    Figure 14 REPLACING ABRASIVE DISC (Fig. 15) 1. Remove table assembly. 2. Remove disc cover (1) by loosening and removing five screws (2). 3. Remove old abrasive disc by peeling it from the aluminum disc. Removng aluminum disc is not necessary.

  • Page 10: Maintenance

    MAINTENANCE GENERAL MAINTENANCE LUBRICATION The shielded ball bearings in this have been are WARNING permanently lubricated at the factory. They require no further lubrication. • For your own safety, turn switch OFF and remove the • When operation seems stiff, a light coat of paste wax plug from power source receptacle before maintaining, applied to the table will make it easier to feed the work cleaning, adjusting, or lubricating your sander.

  • Page 11: Troubleshooting

    TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION Motor will not start 1. Low voltage 1. Check power line for proper voltage 2. Open circuit in motor or loose 2. Inspect all lead connections on motor for loose connections or open connection 3.

  • Page 12: Parts Illustration

    6"X 9" BELT/DISC SANDER PARTS ILLUSTRATION...
  • Page 13 6"x 9" BELT/DISC SANDER PARTS LIST Key No. Part No. Description Specification Key No. Part No. Description Specification 1 BD6900001 Idler Drum 60 BD6900060 Dust Chute 2 BD6900002 Bearing 6201-2Z 61 BD6900061 Socket Head Screw M8x10 62 BD6900062 Driver Pulley 3 BD6900003 Lock Nut 6 63 BD6900063 Sponge 4 BD6900004 Rubber Sleeve...
  • Page 14 Key No. Part No. Description Specification Key No. Part No. Description Specification 119 BD6900119 Dust Bag 130 BD4800135 Cross Recessed Pan Head Screw 120 BD6900120 Flat Washer 131 BD4800136 Flat Washer 121 BD6900121 Pan Head Screw 132 BD4800140 Flat Washer 6 122 BD6900122 Guard 133 BD4800137 Pointer 123 BD4800127 Pin 10x20...

  • Page 15: Warranty

    30- DAY SATISFACTION GUARANTEE POLICY During the first 30 days after the date of purchase, if you are dissatisfied with the performance of this POWERTEC tool for any reason, you may return the tool to the retailer from which it was purchased for a full refund or exchange. You must present proof of purchase and return all original equipment packaged with the original product.

Table of Contents