Table of Contents
Advertisement
Quick Links
Owner's Manual
1" x 30" BELT SANDER
QUESTION...
1•847•780•6120
Visit us on the web at www.southerntechllc.com
You will need this manual for safety instructions, operating procedures, and warranty.
Put it and the original sales invoice in a safe, dry place for future reference.
Model No. BD1030
16-527
Advertisement
Table of Contents
Related Manuals for PowerTec BD1030
Summary of Contents for PowerTec BD1030
- Page 1 Model No. BD1030 Owner’s Manual 1" x 30" BELT SANDER QUESTION... 1•847•780•6120 Visit us on the web at www.southerntechllc.com You will need this manual for safety instructions, operating procedures, and warranty. Put it and the original sales invoice in a safe, dry place for future reference.
-
Page 2: Table Of Contents
TABLE OF CONTENTS PRODUCT SPECIFICATIONS SECTION PAGE Horsepower ....... . . 1/3 Voltage . -
Page 3: Safety Rules
GENERAL SAFETY RULES • Keep children and visitors away. Your shop is a WARNING potentially dangerous environment. Children and visitors For your own safety, read and understand all warnings can be injured. and operating instructions before using any tool or •... -
Page 4: Assembly
ASSEMBLY UNPACKING • Take apart the locking lever assembly (hex headed bolt, washer, splined shaft, lever and screw with spring). Refer to Figure 1. Check for shipping damage. Check immediately whether Figure 3 all parts and accessories are included. Washer The sander comes assembled as one unit. -
Page 5: Replacing The Sanding Belt
To adjust sanding belt table: Figure 7 Wheel Belt WARNING Tracking Knob Sanding To prevent trapping the workpiece or fingers between the Belt table and the sanding belt adjust the sanding belt table to a maximum of 1/16" from the backstop. •... -
Page 6: Backstop
BACKSTOP Figure 9 Bolt Refer to Figure 8 Flat Washer The backstop is a surface to sand against. Sander The backstop can be removed for polishing and contour Rubber sanding. Washer • Remove screws and washers securing backstop. Place screws, washers and backstop in a safe place for future Workbench use. -
Page 7: Extension Cords
Figure 10 Extension Cord Length Ground Outlet Box Wire Size…………….. A.W.G. Up to 25 ft…………… 16 gauge NOTE: Using extension cords over 25 ft. long is not 3-Prong Plug recommended. MOTOR Grounding Prong The sander is equipeed with a 3 Amps motor. The 120 Volt motor has the following specifications:: Horsepower .............. -
Page 8: Operation
OPERATION ON/OFF SWITCH SURFACE SANDING ON SANDING BELT Refer to Figure 13 Hold the workpiece firmly with both hands. Keep fingers away from sanding belt. Keep the workpiece end against • To turn the sander ON, place the ON/OFF switch in the the backstop and move it slowly across the sanding belt. -
Page 9: Troubleshooting
TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION Sanding Grains 1. Sanding belt has been stored in 1. Ensure sanding accessories are stored away easily rub off belt. an incorrect environment. from extremely hot or dry temperatures. 2. Sanding belt has been 2. -
Page 10: Parts Illustration
1" x 30" BELT SANDER PARTS ILLUSTRATION... - Page 11 1" x 30" BELT SANDER PARTS LIST Key# Part# Description Specification Key# Part# Description Specification BD1030001 Side Cover BD1030025 Axle Seat Φ3X18 BD1030002 Cover Knob BD1030026 Spring Pin BD1030003 Sanding Belt 25.4*762mm/80# BD1030027 Spring BD1030004 Rear Driven Wheel BD1030028 Tension Handle Φ15 BD1030004.1 C-Ring...
-
Page 12: Warranty
30- DAY SATISFACTION GUARANTEE POLICY During the first 30 days after the date of purchase, if you are dissatisfied with the performance of this POWERTEC tool for any reason, you may return the tool to the retailer from which it was purchased for a full refund or exchange. You must present proof of purchase and return all original equipment packaged with the original product. - Page 13 NOTE...
- Page 14 NOTE...
- Page 15 NOTE...
- Page 16 Southern Technologies, LLC 3816 Hawthron CT, Waukegan, IL 60087...