Table of Contents
Advertisement
I.
II.
III.
IV.
V.
VI.
robot coupe U.S.A., Inc.
P.O. Box 16625, Jackson, MS 39236-6625
264 South Perkins St., Ridgeland, MS 39157
email: info@robotcoupeusa.com
website: www.robotcoupeusa.com
1-800-824-1646
OPERATION MANUAL
Models
R502 Series E
Serial Numbers: 537xxxxx03
R602 Series E
Serial Numbers: 540xxxxx03
Also includes submodels R502Y,
R602Y, R502X and R602X
INTRODUCTION
ASSEMBLY/DISASSEMBLY INSTRUCTIONS
PREVENTIVE MAINTENANCE GUIDE
SERVICE AGENCY LISTING
PARTS DRAWINGS & PART LISTS
ELECTRICAL SCHEMATICS
SERVICE AGENCY LIST
FOR
and
August 2009
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Robot Coupe R502
Summary of Contents for Robot Coupe R502
- Page 1 OPERATION MANUAL Models R502 Series E Serial Numbers: 537xxxxx03 R602 Series E Serial Numbers: 540xxxxx03 Also includes submodels R502Y, R602Y, R502X and R602X INTRODUCTION ASSEMBLY/DISASSEMBLY INSTRUCTIONS III. OPERATING INSTRUCTIONS PREVENTIVE MAINTENANCE GUIDE TROUBLE SHOOTING AIDS SERVICE AGENCY LISTING PARTS DRAWINGS & PART LISTS...
- Page 2 R502 and R602 Operation Manual Series E versions IMPORTANT NOTICE 3-PHASE MOTORS DRIVE SHAFT ROTATION Three phase motors may rotate either direction. counterclockwise The required motor rotation is Check the rotation before attaching the cutter blades. Changing the motor rotation requires a qualified electrician.
- Page 3 Otherwise, the motor can overheat. amps on high speed. The machines are supplied with stain- less steel bowls: the R502 with a five quart and the R602 hav- ing a 7 quart bowl. Both machines are supplied with s-blade and clear polycarbonate cover. The machines are supplied with a continuous feed attachment and 2 cutting discs as standard equipment.
- Page 4 R502 and R602 Operation Manual Series E versions II. ASSEMBLY / DISASSEMBLY and clean so the grid can be firmly seated. The discharge plate must be in the machine or the product will not exit. INSTRUCTIONS With the tab on the plastic grid aligned with the cutout in the A.
- Page 5 R502 and R602 Operation Manual Series E versions C. Assembling the Cutter Bowl Attachment E. Blade Assembly / Disassembly 1. The cord should always be unplugged during assembly The blade should be disassembled and cleaned at least and disassembly. once a day and after each day’s use.
- Page 6 R502 and R602 Operation Manual Series E versions 5. Assemble the blades as shown, with the small nylon DO NOT attempt to run frozen products through spacer directly under the top locking nut. The blades the cutting plates. should be installed beveled side up. The correctly assembled blade looks like the letter “S”.
- Page 7 User applications may require additional discs. The The 28133 (1") slicer also provides an excellent cut of lettuce Robot Coupe processor will perform a variety of functions: slic- for use in a salad. ing grating dicing, and julienne. There are a total of 34 different discs available to perform these functions (see below).
- Page 8 R502 and R602 Operation Manual Series E versions When dicing tomatoes, green peppers, onions, or celery al- ways insure that the product is introduced into the machine so TO CHOP MEAT: Place meat (precut 1 to 2 inches square) in that the slicing disc will be slicing across the grain of the veg- the bowl.
- Page 9 D. GENERAL HINTS: DO NOT IMMERSE THE MOTOR BASE ASSEMBLY IN WATER. 1. Be sure your Robot Coupe is properly assembled before using. While the continuous feed lead, pushers and discs are dish- 2. Always insure blade and attachment are tightly in place.
- Page 10 Your Robot Coupe is a piece of kitchen equipment and like all 3. Use the robot coupe stone or any good sharpening other kitchen equipment, extreme care and caution should stone.
- Page 11 2. Rim of disc should be slightly above the upper edge of continuous feed attachment. Your Robot Coupe has a one year limited warranty against defects in parts and workmanship. Should the unit require C. Unit stops running during (while) processing.
- Page 12 R502 and R602 Operation Manual Series E versions...
- Page 13 R502 and R602 Operation Manual Series E versions...
- Page 20 KEEP ALL ORIGINAL CONTAINERS AND PACKING MATERIALS FOR CARRIER INSPECTION Robot Coupe U.S.A., Inc., Robot Coupe S.A., or any of their affiliates, distributors, officers, directors, agents, employees or insurers will not be obligated for consequential or other damages, losses, or expenses in connection...