Robot Coupe R 20 Manual
Hide thumbs
Also See for R 20:
- Manual (34 pages) ,
- Instructions of use (33 pages) ,
- Operating instructions manual (26 pages)
Table of Contents
Related Manuals for Robot Coupe R 20
Summary of Contents for Robot Coupe R 20
- Page 1 Register your product on line R 8 • R 10 • R 15 • R 20 R 8 V.V. • R 10 V.V. • R 15 V.V. • R 20 V.V. Blixer 8 • Blixer 10 • Blixer 15 • Blixer ®...
- Page 2 www.robot-coupe.com Register your product on line...
- Page 3 EU Declaration of Conformity Robot-Coupe SNC declares that the machines identified by • the provisions of the following harmonized European standards and the standards specifying the safety and hygiene requirements: their type above, comply with: - EN ISO 12100:2010 Safety of machinery – General principles •...
-
Page 4: Table Of Contents
® A CUTTER MIXER R 8 • R 10 • R 15 • R 20 • Blades • R 8 V.V. • R 10 V.V. • R 15 V.V. • R 20 V.V. • • Seal Blixer 8 • Blixer 10 •... -
Page 5: Warranty
ROBOT-COUPE , LIMITED WARRANTY S.N.C. Labour to sharpen and/or replacements for SHIPPING DAMAGES. Visible and latent Your new ROBOT-COUPE appliance is blades which have become blunt, chipped or defects are the responsibility of the freight carrier. warranted to the original buyer for a The consignee must inform the carrier and worn after a normal or excessive period of use. - Page 6 Blixer ® 15 V.V. 50 or 60 Hz current may fail to trip a differential circuit breaker themselves of electrostatic charges. R 20 V.V. Three-phase that is only sensitive to alternating current (type AC). Blixer 20 V.V. ® • The machine must be disconnected from the mains...
-
Page 7: Important Warning
W A R N I N G IMPORTANT WARNING KEEP THESE INSTRUCTIONS IN A SAFE PLACE WARNING: In order to limit accidents such as electric shocks or personal injury, and in order to limit material damage due to misuse of the appliance, please read these instructions carefully and follow them strictly. -
Page 8: You Have Just Purchased Ablixer Or A Cutter Mixerr 8 • R 10 • R 15 • R
220V/ 60 Hz / 3 • R 20 V.V. • Blixer 8 • R 8 • R 10 • R 15 • R 20 • R 8 V.V. • R 10 V.V. • ® 230V/ 50 Hz / 3 R 15 V.V. • R 20 V.V. -
Page 9: Assembly
• If the lid parts are already assembled: ASSEMBLY W A R N I N G 4) Place the lid assembly in • MACHINE There is a green safety indicator light on the the correction position. Next, 1) With the motor base facing control panel of the motor unit. -
Page 10: Options (Cutter Only)
USES at least 2 speeds 1,500 and 3,000 rpm (patented R 8 / R 10 Variable-speed cutter: R 8 R 10 R 15 R 20 summary R 15 / R 20 system exclusive to Robot-Coupe) plus 100% stainless - 1 speed: 1200 to 1500 rpm. -
Page 11: Vacuum Kit R-Vac
The serrated blades are mainly used : The 100% stainless-steel blade assemblies of our CLEANING cutter and Blixer can be taken apart for easy ® - for making pastry W A R N I N G cleaning - for grinding. After cleaning the blade, always dry well to prevent As a precaution, always unplug your appliance The fine serrated blades are mainly used for:... -
Page 12: Maintenance
It is strongly recommended, after each use, to give R 8 • R 10 • R 15 • R 20 • Blixer 8 • Blixer ® ® the mini bowl is supplied the blades a quick sharpen with a sharpening steel, •... -
Page 13: Seal
• SEAL DIAGNOSTIC SYSTEM 2) Flashing green light The seal on the motorshaft should be lubricated R E M E M B E R Your appliance is equipped with a light that indicates regularly using a food safe lubricant. the operational status of your machine: After switching your appliance on, open In order to keep the motor completely watertight, it is - no green light: see paragraph 1. - Page 14 • Test sequence: Level 3: The flashing of the green light indicates which element needs to be checked. If you have not been using your machine intensively, When the green light flashes, start by pressing button A rapidly flashing light indicates that either the base when it may be quite normal for the motor to overheat I to test that it is working properly (as the buttons are (ISBC) or the lid (ISCO) presence sensor is posing a...
-
Page 15: Operating Instructions For The Vacuum Kit R-Vac
OPERATING INSTRUCTIONS FOR THE VACUUM KIT R-VAC (Cutter only) ® 1° ASSEMBLING THE VACUUM KIT R-VAC ® - Insert filter N° 2 into body N° 3 - Screw part N° 1 onto body N° 3 (the tube is fed through body N° 3). 2°... -
Page 16: Fitting And Using The Blade Assembly
FITTING AND USING THE BLADE ASSEMBLY Plastic Narrow Blade Screw Blade Long ring ring spacer shaft (Cutter only) • 2-BLADE ASSEMBLY: • 3-BLADE ASSEMBLY: We recommend you use the 3-blade assembly for processing large quantities of more than half the We recommend you use the two-blade assembly for processing small maximum limit indicated, with the exception of liquid or blended preparations for which we strongly amounts (less than half the maximum capacity indicated on page 9). - Page 17 FITTING AND USING THE BLADE ASSEMBLY Plastic Narrow Blade Screw Blade Long ring ring spacer shaft (Blixer only) ® • 2-BLADE ASSEMBLY: • 3-BLADE ASSEMBLY: (except Blixer ® We recommend you use the two-blade assembly for processing We recommend you use the 3-blade assembly for processing large quantities of more than half small amounts.
-
Page 18: Technical Specifications
® 220V/60 Hz / 3 1,800 400 V = 6 R 15 / 15 V.V. - Blixer 20 / 20 V.V. - R 20 / 20 V.V. ® 230 V = 11 380V/60 Hz / 3 3,600 on a stable surface. There is no recommended 400 V = 6.5... -
Page 19: Safety
R 20 • Blixer 20 dual-speed Three-phase appliance However, if you are processing liquid ingredients, it ® is a good idea to stop the machine before opening Speed 1 Speed 2 Intensity the lid, to avoid splashing. Motor (rpm) (rpm) (Amp.) - Page 44 19/01/2018...
- Page 45 19/01/2018...
- Page 46 19/01/2018...
- Page 47 19/01/2018...
- Page 48 Head Office, French, Robot Coupe Australia Pty Ltd: Robot-Coupe U.K. LTD: Export and Marketing Department: Unit 3/43 Herbert St Fleming Way, Isleworth, 48, rue des Vignerons Artarmon NSW 2064 Australia Middlesex TW7 6EU 94305 Vincennes Cedex- France Tel.: (02) 9478 0300 Tel.: 020 8232 1800...