Table of Contents
Related Manuals for Robot Coupe R 502 G
Summary of Contents for Robot Coupe R 502 G
- Page 1 R 502 G • R 502 V.V. G R 702 • R 702 V.V. • R 752 • R 752 V.V. Robot Coupe U.S.A., Inc. 264 South Perkins, Ridgeland, MS 39157 - Phone: 800/824-1646 • 601/898-8411 email: info@robotcoupeusa.com - website: www.robot-coupe.com...
- Page 2 • This machine must be operated on a clean sturdy • Should the machine malfunction or should any part • Robot Coupe can in no way be held responsible for counter or table. Keep the area around and under the be damaged, it must not be operated until it is repaired the user’s failure to follow the basic rules of cleaning and...
- Page 3 www.robotcoupeusa.com Register your product online We reserve the right to alter at any time without notice the technical specifications of this appliance. None of the information contained in this document is of a contractual nature. Modifications may be made at any time. ©...
-
Page 4: Table Of Contents
CONTENTS WARRANTY MAINTENANCE • Blade IMPORTANT WARNING • Motor seal INTRODUCTION TO YOUR NEW • Scraper arm R 502 • R 502 V.V. • Blades, combs and grater R 702 • R 702 V.V. • R 752 • R 752 V.V. BOWL CUTTER / VEGETABLE PREPARATION TECHNICAL SPECIFICATIONS SWITCHING ON THE MACHINE... - Page 5 ROBOT COUPE U.S.A., INC. ONE YEAR LIMITED COMMERCIAL WARRANTY THE FOLLOWING ARE NOT COVERED Commercial equipment use is defined as but not limited to the preparation of food substance within the confines YOUR NEW ROBOT COUPE COMMERCIAL UNDER WARRANTY: of a restaurant/facility, that is sold and consumed within PRODUCT IS WARRANTED TO THE said restaurant/facility.
- Page 6 RECOMMENDATIONS CONCERNING THE INSTALLATION OF VARIABLE-SPEED APPLIANCES AND THE PROTECTION OF PERSONS These recommendations apply to machines fitted Circuit interrupters ensuring users safety with an AC induction motor and a single phase • Ground Fault Circuit Interrupters (GFCIs) Variable Frequency Drive (VFD). intended for variable-speed appliances need to be selected with great care in order to ensure Protecting your appliance...
-
Page 7: Important Warning
W A R N I N G IMPORTANT WARNING KEEP THESE INSTRUCTIONS IN A SAFE PLACE WARNING: In order to limit accidents such as electric shocks or personal injury, and in order to limit material damage due to misuse of the appliance, please read these instructions carefully and follow them strictly. -
Page 8: Introduction To Your Newr 502 • R 502
INTRODUCTION TO YOUR SWITCHING ON GREEN YELLOW is the earth, DO NOT DISCONNECT THE MACHINE NEW R 502 • R 502 V.V. Swap either: and the ➊ ➋ R 702 • R 702 V.V. • ADVICE ON ELECTRICAL CONNNECTIONS and the ➊... -
Page 9: Timer
• TIMER display to zero by pressing the + and − buttons at 3) Place the lid equipped the same time or by pressing the "Off" button on with the scraper arm on How the timer works the food processor for 2 seconds. the bowl (see page 14) The timer has three 7-segment LED displays, two f) Standby Mode... - Page 10 Models R 752/ R 752 V.V. 2) Fit the plastic sling plate 3) Position your chosen disc: onto the motor shaft and Two types of tool are designed for the lever-type a) If you have opted for a check that it is correctly hopper: slicing, grating or julienne positioned at the bottom of...
-
Page 11: Operation
Next, fit the corresponding In the case of dicing or French fries cutting slicing disc (straight- equipment, you should pull out the grid and disc edged blade) and rotate assembly in one go. The discharge plate can then in a clockwise direction be removed by means of the two holes. - Page 12 Do not fill the bowl with any solid food over ¾ full NOTE: 1- Among other protections, the machine is 2. TO PUREE OR FINE CHOP: For a fine puree, emulsification, or fine chop, fill the bowl not more equipped with two manual reset overload circuit- nor with any liquid food above the tube in center of than ⅔...
- Page 13 7. TO MAKE BREAD CRUMBS: Place torn fresh Vegetable preparation will be required to DO NOT put your hands, utensils, or anything or dried bread in the bowl. Select the high speed assure that the produce will fit a port opening. other than food product into the feed openings or and operate the machine with Pulses.
-
Page 14: Options
a long grated product, while vertical insertion in the Julienne Operation: Insertion of the product to • MOTOR BASE smaller port will result in a short grated product. It be cut must be horizontal if a long "stick" is to be Never immerse the motor base in water. -
Page 15: Blade
• VEGETABLE PREPARATION ATTACHMENT The blade must always be removed for cleaning Remove each of the parts, i.e.: the lid, disc, sling plate and bowl by pushing the stainless steel button and clean. Diswashers are best avoided especially for the lid. Instead we recommend that you clean the machine by hand, using washing-up liquid. -
Page 16: Motor Seal
/ R 502 V.V. 21 1/4 14 3/8 10 15/16 10 5/8 15 13/16 14 7/8 R 502 G / R 702 R 702 / R 702 V.V. 22 7/16 14 3/8 10 15/16 10 5/8 15 13/16 14 7/8 •... -
Page 17: Safety
ERGONOMICS PRINCIPLE SAFETY SERVICE W A R N I N G See warranty first then; The food processor is composed of a motor base and 2 accessories: Should your unit require service, check with your The blades and discs are extremely sharp. distributor to see where local service is available. -
Page 18: Technical Data
TECHNICAL DATA 16/11/2021... - Page 19 16/11/2021...
- Page 20 16/11/2021...
- Page 21 Robot Coupe U.S.A., Inc., Phone: 800/824-1646 • 601/898-8411 264 South Perkins St., Ridgeland, MS 39157 e-mail: info@robotcoupeusa.com website: www.robot-coupe.com...
Need help?
Do you have a question about the R 502 G and is the answer not in the manual?
Questions and answers