Additional Operation Features - Braeburn 5200 User Manual

ADDITIONAL
5
OPERATION FEATURES
Review Set Temperature
5.1
1. Press and hold the or button. The current setpoint temperature will be displayed
in the place of the current room temperature, and the indicator SET TEMP will be displayed.
2. The display will return to normal operating mode
when the or button is released. Continuing to
hold the or button for 3 seconds or longer will
allow the user to temporarily override the current
programmed setpoint (See Temporary Program Override).
Temporary Program Override
5.2
1. Press and hold button for 3 seconds. The entire display will flash once and the SET
or
TEMP indicator will be displayed. Release the
again as desired to adjust the set temperature.
2. The display will return to normal operating mode after
15 seconds or you can press the RETURN button.
3. The program indicator (MORN, DAY, EVE OR NIGHT)
will be flashing in the display, indicating that a Temporary
Program Override is in effect. The Temporary Program
Override will reset when the next setpoint time occurs,
or after 4 hours – whichever comes first.
Extended Hold (Vacation) Mode
5.3
1. Press the HOLD button to bypass the program schedule. The current setpoint temperature
will be held until HOLD is released, and HOLD and TEMP will show in the display.
2. Press the HOLD button again to return the thermostat
to normal program operation.
3. The hold period lasts until the hold is released as in
step #2 above, or is limited to 24 hours if the default
was changed in the User Options Settings (section 4.3.3).
Filter Check Monitor (see section 4.3.4 for setting)
5.4
The Filter Check Monitor displays a reminder for required filter replacement or cleaning, by
flashing the FILT segment in the display. See instructions on your filter or heating/cooling unit
for recommendations for interval setting.
When the selected interval has been reached, and
required cleaning or replacement has been performed,
press the RETURN button in any normal mode to reset
the timer and turn off the warning.
Locking the Keypad
5.5
To prevent accidental or undesired adjustment of the thermostat, the Keypad Lock feature
disables the operation of the keypad, except for the backlight key. In order to lock the
keypad, press and hold both and buttons together
at the same time for 5 seconds. The LOCK segment in the
display will flash once per second, and then appear
continuously in the display. The keypad is now locked.
To unlock the keypad, press and hold the and buttons
together at the same time for 1 second. The LOCK segment
will disappear and the keypad will become unlocked.
or button and press the or button
DAY
FILT
LOCK
MORN
HEAT
10
ADDITIONAL
5
OPERATION FEATURES
Adaptive Recovery Mode (ARM™)
5.6
This thermostat is equipped with a special feature to maximize your energy savings by
utilizing the most effective source of heating or cooling to meet your program needs during
recovery from setback (or setup) temperatures. Our Adaptive Recovery Mode (ARM™) feature
is designed to automatically calculate when to turn your first (heat pump) stage of your
multi-stage heating or cooling system to meet your upcoming comfort setpoint temperature
setting. While in normal operating mode, this feature will start calculating the start time for
your first stage (heat pump) two hours prior to the upcoming comfort setpoint temperature.
During this two hour time period it will monitor performance and control your system staging
requirements. The second (auxiliary) stages of heating or cooling will be available during this
2-hour period if required to meet extraordinary heating or cooling requirements.
Recirculating Fan Feature (see section 4.3.4)
5.7
The Recirculating Fan Mode provides more even temperature distribution and improves
indoor air quality by circulating air through the furnace filtration system more often. The
Recirculating Fan Mode can be selected by moving the fan switch to the recirculate position
( ). If no call for heating or cooling occurs within the fan off cycle set in section 4.3.5,
the fan will run for 12 minutes. The highest setting, 120 minutes (factory default), will run
the fan least often – 9% minimum run time. The lowest setting, 40 minutes, will run the fan
most often – 23% minimum run time. During any call for heating or cooling, fan control
operates in the AUTO mode. The Recirculating Fan feature is available in the HEAT, OFF, or
COOL mode.
Auxiliary Heat Fossil Fuel Switch
5.8
The Model 5200 is equipped with an auxiliary heat option switch which is set at
installation for either an electric or fossil fuel (gas, oil or propane) auxiliary heat source.
For heat pump units with an electric auxiliary stage, both the first and second stages of
heating will run when a call for second stage heat is made. For heat pump units with a
fossil fuel auxiliary stage, the first stage will be locked out one minute after a second
stage heat call, and the second stage alone will be used.
cont.
11