Related Manuals for JAI EL-2800M-PMCL
Summary of Contents for JAI EL-2800M-PMCL
- Page 1 Elite Series User Manual EL-2800M-PMCL EL-2800C-PMCL 2.8M Digital Progressive Scan Monochrome and Color Camera Document Version: 1.5 EL-2800-PMCL_Ver.1.5_Oct2013 1043E-1302...
- Page 2 JAI Ltd., Japan and may only be used by the purchasers of the product. JAI Ltd., Japan makes no warranty for the use of its product and assumes no responsibility for any errors which may appear or for damages resulting from the use of the information contained herein.
- Page 3 EL-2800M-PMCL Supplement The following statement is related to the regulation on “ Measures for the Administration of the control of Pollution by Electronic Information Products “ , known as “ China RoHS “. The table shows contained Hazardous Substances in this camera.
- Page 4 EL-2800C-PMCL Supplement The following statement is related to the regulation on “ Measures for the Administration of the control of Pollution by Electronic Information Products “ , known as “ China RoHS “. The table shows contained Hazardous Substances in this camera. mark shows that the environment-friendly use period of contained Hazardous Substances is 15 years.
-
Page 5: Table Of Contents
EL-2800M-PMCL / EL-2800C-PMCL - Contents - Before using this manual ..............- 6 - 1. General ..................- 7 - Camera composition ..............- 7 - Main features ................- 8 - Locations and functions ...............- 9 - Locations and functions ..............- 9 - 4.2. - Page 6 EL-2800M-PMCL / EL-2800C-PMCL 6.3.2 Vertical timing ..................- 27 - 6.3.2.1 Output format 1X2–2YE , 1X–2YE ..............- 27 - 6.3.2.2 Output format 1X2–1Y , 1X–1Y ................. - 28 - 6.3.3 ROI (Region Of Interest) ................- 28 - Digital output bit allocation .............. - 29 - Operating modes ..............
- Page 7 Transport Layer Control ................- 66 - 2.4.10 User Set Control ..................- 66 - 2.4.11 JAI-Custom ................... - 67 - Appendix 2 ................... - 82 - 1. Precautions ..................- 82 - 2. Typical Sensor Characteristics .............. - 82 - 3.
-
Page 8: Before Using This Manual
EL-2800M-PMCL / EL-2800C-PMCL Before using this manual EMVA 1288 With regard to signal to noise ratio in this manual, specifications measured by EMVA 1288 are used together with specifications by a traditional measurement method. EMVA 1288 is a more complete measurement that considers multiple noise sources, including random noise, pattern noise, and shading. -
Page 9: General
As a common Elite Series feature, a new connector for lens control is employed. EL-2800M-PMCL and EL-2800C-PMCL support P-iris and motor-driven lenses as standard lens control capabilities. -
Page 10: Main Features
Various readout modes, including horizontal and vertical binning (EL-2800M-PMCL only) and ROI (Region Of Interest) for faster frame rates 0dB to +30dB gain control for EL-2800M-PMCL and 0dB to +27dB for EL-2800C-PMCL 10 μs (1/100,000) to 8 seconds exposure control in 1 μs step ... -
Page 11: Locations And Functions
EL-2800M-PMCL / EL-2800C-PMCL Locations and functions Locations and functions Lens mount C-mount (Note *1) 10-pin AUX connector Standard (Connector for lens control) LED Indication for power and trigger input 12-pin connector DC+12V and trigger input Camera Link Connector 2 Digital video output (Medium configuration) (Note *2) ... -
Page 12: Rear Panel
EL-2800M-PMCL / EL-2800C-PMCL 4.2. Rear Panel The rear panel mounted LED provides the following information: Amber: Power connected – initiating This light goes OFF after initiating. Steady green: Camera is operating in Continuous mode Flashing green: The camera is receiving external triggering Note: The interval of flashing does not correspond with external trigger duration. -
Page 13: Input And Output
EL-2800M-PMCL / EL-2800C-PMCL 5. Input and output Connectors and pin assignment 5.1.1 12-Pin connector 5.1.1.1 Figure Type: HR10A-10R-12PB-01 (Hirose) male or equivalent. Use the part number HR10A-10P-12S for the cable side Fig.3 Hirose 12-pin connector 5.1.1.2 Pin assignment Table – 1 12P pin assignment Pin no. -
Page 14: Aux Standard Hirose 10-Pin Connector
EL-2800M-PMCL / EL-2800C-PMCL 5.1.2.2 Pin assignment Table – 2 Camera Link connector 1 Pin assignment Pin No In/Out Name Note 1,26 Power Power 2(-),15(+) TxOUT0 3(-),16(+) TxOUT1 Data out 4(-),17(+) TxOUT2 5(-),18(+) TxClk Clock for CL 6(-),19(+) TxOUT3 Data out... -
Page 15: Aux Type 2 Hirose 10-Pin Connector (Factory Option)
EL-2800M-PMCL / EL-2800C-PMCL Table – 4 AUX Standard Hirose 10P connector pin assignment Name Note DRIVE IRIS+ Motorized Lens DRIVE FOCUS+ Motorized Lens DRIVE ZOOM+ Motorized Lens COMMON Motorized Lens P-IRIS OUT1A P-Iris Lens P-IRIS OUT1B P-Iris Lens P-IRIS OUT2A... -
Page 16: Camera Link Interface
EL-2800M-PMCL / EL-2800C-PMCL Camera Link interface Table – 7 Camera Link interface EL-2800M/C-PMCL Camera Link Configuration Base Medium Base Port Camera Link port/bit 1Tap / 12bit 2ap / 12bit 4 Tap / 12bit 1 Tap / 8bit GenICam Tap Geometry... -
Page 17: Digital In/Ouit Interface
EL-2800M-PMCL / EL-2800C-PMCL Digital IN/OUIT interface In the EL-2800 the software control tool can assign the necessary signals to the digital I/O ports. 5.3.1 Line Selector In the Line Selector, the following input and output signals can be assigned. Line 1 TTL Out 1... -
Page 18: Line Status
EL-2800M-PMCL / EL-2800C-PMCL 5.3.5 Line Status Indicates the status of the selected signal, input or output (True=High or False=Low) 5.3.6 Line Format Indicates the current interface of the selected line item, input or output. Input CC1 In Line 4 TTL In 1... -
Page 19: Pulse Generator
EL-2800M-PMCL / EL-2800C-PMCL The following table shows the input and output matrix. Table – 10 GPIO input and output matrix Trigger Line Pulse Generator Selector Selector Selector Selector （Cross Point Switch Output） Source Signal (Cross Point Switch Input) ○ ○... -
Page 20: Clock Pre-Scaler
EL-2800M-PMCL / EL-2800C-PMCL Table - 11 Pulse Generator default settings Display Name Value Clock Pre-scaler Pulse Generator Length Start Repeat Clear Clear Clear Clear Pulse Generator Point Point Count Source Inverter Activation Sync Selector Mode True Async Mode Pulse Generator 0... -
Page 21: Pulse Generator Length
EL-2800M-PMCL / EL-2800C-PMCL Pulse generator Clear source IN (Clear activation = Rising edge Pulse generator repeat count = N Clear SYNC mode (Pulse generator length x N) = Async) Pulse generator Pulse generator Pulse generator length length length Pulse generator... - Page 22 EL-2800M-PMCL / EL-2800C-PMCL (Example1) Clear Activation = Rising Edge, Clear Sync Mode = Async Mode, Clear Inverter = False Pulse Generator Clear Source In Pulse Generator Output Clear ↓ Fig.8 Counter clear in Async mode (Example2) Clear Activation = Rising Edge, Clear Sync Mode = Sync Mode,...
-
Page 23: Pulse Generator Clear Source
EL-2800M-PMCL / EL-2800C-PMCL 5.4.9 Pulse Generator Clear Source The following clear source can be selected as the pulse generator clear signal. Table - 13 Pulse generator clear source Pulse Generator Clear Source Description item Connect Low level signal to Clear Source for the selected pulse generator. -
Page 24: Pulse Generator Inverter
EL-2800M-PMCL / EL-2800C-PMCL 5.4.10 Pulse Generator Inverter Clear Source Signal can have polarity inverted. 5.4.11 Pulse Generator Setting table Table - 14 Pulse Generator setting parameters Display Name Value Clock Pre-scaler 1 to 4096 Pulse Generator Clock (MHz) [Pixel Clock:54MHz]÷[Clock Pre-scaler]... -
Page 25: Sensor Layout, Output Format And Timing
EL-2800M-PMCL / EL-2800C-PMCL Sensor layout, output format and timing Sensor layout CCD sensors used in the EL-2800M-PMCL and EL-2800C-PMCL have the following tap and pixel layout. 6.1.1 Monochrome sensor Tap 3 Tap 4 Tap 1 Tap 2 1920 Pixels Fig.10 Monochrome sensor layout 6.1.2... -
Page 26: Camera Output Format
EL-2800M-PMCL / EL-2800C-PMCL 6.2. Camera output format The EL-2800M-PMCL and EL-2800C-PMCL have the following camera output formats described in GenICam SFNC Ver.1.5.1 as Tap Geometry. Table – 15 Camera output format Camera output format Tap geometry Reference figure 1X–1Y Single tap 6.2.1... -
Page 27: 1X2-1Ye
EL-2800M-PMCL / EL-2800C-PMCL 6.2.3 1X2–1YE 1X2–1YE is also for 2-tap readout but the readout system is right and left as below. Step X = 2 Tap 1 Tap 2 X5120 X1913 X1914 19115 X1916 X1917 X1918 X1919 X1920 X1920 X1920... -
Page 28: Output Timing
EL-2800M-PMCL / EL-2800C-PMCL Output timing 6.3.1 Horizontal timing 6.3.1.1 Output format 1X2-2YE , 1X2–1Y a) Vertical binning OFF LVAL DVAL Video (Tap 1, 2/Tap 3,4) 411Clk = Exposure Start Line 305Clk = Other line Exposure Active (Exposure Start Line) 1421Clk = Exposure Start Line 1315Clk = Other Line Fig.16... -
Page 29: Vertical Timing
EL-2800M-PMCL / EL-2800C-PMCL b) Vertical binning ON LVAL DVAL Video (Tap 1/Tap 2) 625Clk = Exposure Start Line 1920 532Clk = Other line Exposure Active (Exposure Start Line) 2645Clk = Exposure Start Line 2552Clk = Other Line Fig.19 Horizontal timing (Vertical binning ON) 6.3.2... -
Page 30: Output Format 1X2-1Y , 1X-1Y
See section 7.1.2 for formulas that can be used to calculate the maximum frame rate for a specific ROI. ROI can be set from 8 lines to 1440 lines in one-line increments for the EL-2800M-PMCL, or in two-line increments for the EL-2800C-PMCL. -
Page 31: Digital Output Bit Allocation
EL-2800M-PMCL / EL-2800C-PMCL Digital output bit allocation Table – 16 Output level CCD out Digital Out Analog Out (equivalent) 8bit 10bit 12bit Setup 3.6%, Black 8LSB 32LSB 128LSB 25mV Monochrome 574mV 100% 700mV 222LSB 890LSB 3560LSB Color 386mV Monochrome 662mV... -
Page 32: Calculation Of Default Frame Rate
EL-2800M-PMCL / EL-2800C-PMCL ROI should be set first using Height and Offset Y settings in Image Format Control. The number shown in Acquisition Frame Rate (RAW) will correspond to the fastest frame rate for the specified ROI. The value can be adjusted as low as 0.125 fps (8 seconds per frame). -
Page 33: Exposure Time
EL-2800M-PMCL / EL-2800C-PMCL Table – 17 Exposure mode Trigger Control Trigger OFF Trigger ON Exposure Mode Frame Start Behavior Self-running OFF or ON No exposure control Self-running Timed (EPS) Exposure control Timed(RCT) available Timed (PIV) Operate in EPS, RCT or PIV... -
Page 34: Trigger Mode
EL-2800M-PMCL / EL-2800C-PMCL ALC Speed: Rate of adjustment can be set (Common with Gain auto) Exposure Auto Max: The maximum value for the exposure time to be controlled can be set Exposure Auto Min: The minimum value for the exposure time to be controlled can... -
Page 35: Timed (Eps) Mode
EL-2800M-PMCL / EL-2800C-PMCL for the auto-iris lens is available. For the video timing, refer to the chapter 6.3. The frame rate of full pixels readout is 54.7 fps for 4-tap output. Primary settings to use this mode Trigger Mode: Off Table –... -
Page 36: If The Overlap Setting Is Lse Is 54
EL-2800M-PMCL / EL-2800C-PMCL Trigger Exposure Exposure Active Exposure Period FVAL 8.1 μ sec (Typical) 2L (Min) 4.5 ～ 5.5L Fig.26 Overlap OFF 7.5.2 If the overlap setting is lse is 54 Trigger Exposure Exposure Active Exposure Period FVAL 2L (min) 4.5L ～5.5L... -
Page 37: If The Overlap Setting Is Lse
EL-2800M-PMCL / EL-2800C-PMCL The frame rate of full pixels readout is 54.7 fps for 4-tap output. Primary settings to use this mode Exposure mode: Trigger Width Trigger mode: ON Table – 21 Minimum interval of the trigger pulse (1X2–2YE, 8-bit) -
Page 38: If The Overlap Setting Is Lse
EL-2800M-PMCL / EL-2800C-PMCL 7.6.2 If the overlap setting is lse (1X24 Trigger Exposure Exposure Active Exposure Period FVAL 2L (min) 1L + 8 µsec Fig.29 Readout 7.7. RCT mode Until the trigger is input, the camera operates continuously and the video signal for the auto-iris lens is output. -
Page 39: Piv (Particle Image Velocimetry)
EL-2800M-PMCL / EL-2800C-PMCL Trigger Exposure Exposure Active FVAL DVAL Output format 1x2-2YE, 1X-2YE 194L 4.5L ～5.5L 1X2–1Y, 1X – 1Y 384L 4.5L ～5.5L Fig.30 RCT mode timing 7.8. PIV (Particle Image Velocimetry) The Particle Image Velocimetry mode can be used in applications where 2 images need to be taken with a very short time interval. -
Page 40: Sequential Trigger
EL-2800M-PMCL / EL-2800C-PMCL Frame Start Trigger IN Exposure Timing Exposure Active FVAL tframe1 tframe2 DVAL tframe 2 te2 tframe 1 FVAL non active time name description time Exposure beginning delay 8.1 μsec (Typical) First exposure time period 10 μs ～ 2 s... -
Page 41: Sequence Roi Setting Parameters
EL-2800M-PMCL / EL-2800C-PMCL Table - 25 Minimum trigger interval (1X2 – 2YE, 8-bit, Exposure time=10 µs) 4-tap output 1/2V FULL 2/3 ROI 1/2 ROI 1/4 ROI 1/8 ROI Binning Minimum frame line Timed Exposure Mode/Trigger Mode OFF + Exposure Time + 1 Note 1. - Page 42 In Sequence ROI Gain Selector, the gain settings for each index are available. EL-2800C-PMCL: Gain(ALL), Red and Blue can be set. EL-2800M-PMCL: Only Gain is displayed and can be set. (7) Sequence ROI Black Level Black Level setting is available for each index.
- Page 43 EL-2800M-PMCL / EL-2800C-PMCL “Normal” “Normal” “Trigger Sequence” “Trigger Sequence” Video Send Mode Sequence Index Sequence Index Sequence Index Sequence Index Can be changed Can be changed Cannot be changed Cannot be changed Sequence Reset “Execute” Command Sequence Index Pointer Sequen &...
-
Page 44: Operation And Function Matrix
EL-2800M-PMCL / EL-2800C-PMCL 7.10. Operation and function matrix Table – 27 Operation and function matrix Auto Trigger Trigger Auto Auto Exposure White Auto Over Auto mode option Iris Binning Binning Exposure operation Balance gain Exposure (Partial Output Balance (Note1) (Note1) -
Page 45: Other Functions
EL-2800M-PMCL / EL-2800C-PMCL Other functions Black level control This function adjusts the setup level. Variable range: -256 to 255 LSB (at 10-bit output) 8.1.1 Black Level Selector The following factors can be set. EL-2800M: DigitalAll/Tap1All/Tap2All/Tap3All/Tap4All EL-2800C: DigitalAll/Tap1All/Tap1Red/Tap1Blue Tap2All/Tap2Red/Tap2Blue Tap3All/Tap3Red/Tap3Blue Tap4All/Tap4Red/Tap4Blue 8.1.2... -
Page 46: Gain Control
EL-2800M-PMCL / EL-2800C-PMCL Gain control The EL-2800M-PMCL can adjust the gain level from 0dB to +30dB using 0dB as the reference (Factory default). In the EL-2800C-PMCL, the master gain can be adjusted from 0dB to +27dB and R and B gains can be adjusted in the range of -7dB to + 12.99dB using the master gain as the reference. -
Page 47: Gain Raw
Digital Tap4Red/Digital Tap4Blue：-891～+1000 8.2.4 Gain Auto This function automatically controls the gain level. This function is effective only for Frame trigger OFF and RCT modes. This is controlled by the command JAI AGC Reference. There are three modes. OFF: Adjust manually. -
Page 48: Balance White Auto
EL-2800M-PMCL / EL-2800C-PMCL High High High High Mid-left Mid-right Right Left Mid-High Mid-High Mid-High Mid-High Left Mid-left Mid-right Right Mid- Mid-Low Mid-Low Mid-Low Mid-left Mid-right Left Right Mid-left Mid-right Right Left Fig. 36 ALC channel area 8.2.5 Balance White Auto This is auto white balance control function. -
Page 49: Gamma
EL-2800M-PMCL / EL-2800C-PMCL 8.4. Gamma This command is used set gamma between gamma 0.45 and gamma 1.0 (OFF). The gamma value is an approximate value. Fig. 38 Gamma compensation 8.5. Shading Correction This function compensates for shading (non-uniformity) caused by the lens or the light source used. -
Page 50: Blemish Compensation
8.6. Blemish compensation The EL-2800M-PMCL and EL-2800C-PMCL have a blemish compensation circuit. This function compensates blemishes on the CCD sensor (typically pixels with extremely high response or extremely low response). This applies to both monochrome and color versions. Pixels that... -
Page 51: Bayer Color Interpolation (Only For El-2800C)
Fig.43 Color interpolation concept drawing Lens The EL-2800M-PMCL and EL-2800C-PMCL can be used with 4 different types of auto iris lenses, in addition to standard lenses with manual iris control. If an auto iris function is to be utilized, the lens type used must be selected in Lens Select. -
Page 52: About P-Iris
8.8.1 About P-Iris New Elite Series EL-2800M-PMCL and EL-2800C-PMCL come equipped with P-Iris control as part of the standard lens control function. The P-Iris system is a newly developed lens control method designed to control the iris more precisely. Especially for video cameras in surveillance applications utilizing megapixel CCD or CMOS imagers, it becomes a very important factor to control an iris in order to achieve the maximum camera performance. -
Page 53: Motorized Lenses
EL-2800M-PMCL / EL-2800C-PMCL 8.8.3 Motorized lenses The EL-2800C-PMCL and EL-2800C-PMCL can use the 3-axis motorized lens control for zoom, focus and iris. The following functions are available via the motorized lens commands. 8.8.3.1 Iris Open: While this command is supplied, the iris will continue to open. -
Page 54: Alc
Close: Force the iris to close. Open: Force the iris to open. In the EL-2800M-PMCL and EL-2800C-PMCL, auto gain, auto shutter and auto iris functions can be combined to provide a wide ranging automatic exposure control from dark to bright or vice versa. -
Page 55: Camera Control Tool
2. The frame grabber used must be compliant with Camera Link Specification v1.1 or greater in order to communicate with the JAI SDK and Control Tool. If it is not, the JAI SDK and Control Tool cannot be used, and the Short ASCII communication protocol and associated control tool should be used instead. -
Page 56: External Appearance And Dimensions
EL-2800M-PMCL / EL-2800C-PMCL External appearance and dimensions ( 9. 8) 24. 5 3- M3 Dept h5 5. 2 0. 3 3- M3 Dept h5 ( 9. 8) 24. 5 POWER /TRIG AU X D C IN / TRIG DI GITAL I/O -2... -
Page 57: Specifications
EL-2800M-PMCL / EL-2800C-PMCL Specifications 11.1 Spectral response Fig. 47 Spectral response (EL-2800M-PMCL) Fig.48 Spectral response (EL-2800C-PMCL) - 55 -... -
Page 58: Specifications Table
EL-2800M-PMCL / EL-2800C-PMCL 11.2 Specifications table Specifications EL-2800M-PMCL EL-2800C-PMCL Scanning system Progressive scan, 4-tap Synchronization Internal Interface Camera Link (Version 2.0 RC2） BASE/MEDIUM Image sensor 2/3 inch Monochrome CCD 2/3 inch Bayer color CCD Aspect Ratio Image size(Effective Image) 8.72 (h) x 6.54 (v) mm 10.972 mm diagonal Pixel size 4.54 (h) x 4.54 (v) m... - Page 59 EL-2800M-PMCL / EL-2800C-PMCL Timed (EPS,RCT,PIV 10 μs (Min.) ～ 8 sec (Max.)、 Variable unit: 1 μs Exposure Sequential) Mode Trigger Width 1 line + 8 μs (Min.) ～ ～ (Max.) Auto Exposure OFF / Once / Continuous Auto Exposure Response 1 ～...
-
Page 60: Appendix 1 Short Ascii Command Communication Protocol
EL-2800M-PMCL / EL-2800C-PMCL Appendix 1 Short ASCII Command Communication Protocol This chapter described the communication control protocol based on the short ASCII command as the reference. Communication setting Baud Rate 9600 Data Length 8bit Start Bit 1bit Stop Bit 1bit... -
Page 61: Switching Baud Rate Between Pc And Camera
EL-2800M-PMCL / EL-2800C-PMCL Switching baud rate between PC and camera Camera always starts up with 9600bps. This can be switched to higher baud rates after a communication has been established. When switching to other baud rate the procedure is as follows. -
Page 62: Technology Specific Bootstrap Register
EL-2800M-PMCL / EL-2800C-PMCL 2.4.2 Technology Specific Bootstrap Register Acce Short DEFAUL Name Interface Values Description ASCII Indicate Support/Non-support status for each baud rate bit0: 9600bps SupportedBaudr bit1: 19200bps I Integer SBDRT 0x01 0xFF 0x1F SBDRT?<CR><LF> ates bit2: 38400bps bit3: 57600bps... -
Page 63: Image Format Control
EL-2800M-PMCL / EL-2800C-PMCL 2.4.4 Image Format Control Acce Short DEFAU Name Interface Values Description ASCII HTL=[Param.]<CR><LF Height I Integer 1440 1440 Min～(Max - OffsetY) > HTL?<CR><LF> OFL=[Param.]<CR><LF > OFL?<CR><LF> This value is calcurated Offset Y I Integer Min～(Max – Height) -
Page 64: Acquisition Control
EL-2800M-PMCL / EL-2800C-PMCL 2.4.5 Acquisition Control Acce Short DEFAU Name Interface Values Description ASCII FrameStartTrigM TM=[Param.]<CR><LF> Enumerat Off/On TM?<CR><LF> (R)/ TrigSoftware STRG － － － STRG=0<CR><LF> Command 0: Low 1: High 2: SoftTrigger 8: PulseGenerator0 9: PulseGenerator1 10: PulseGenerator2 FrameStartTrigS TI=[Param.]<CR><LF>... - Page 65 EL-2800M-PMCL / EL-2800C-PMCL ND1INV2=[Param.]<CR> LineInverter_N ND1I I Boolean False/True <LF> and1In2 ND0INV2?<CR><LF> 0: Low 1: High FrameTrigg erWait FrameActiv ExposureAc tive 6: Fval 7: Lval PulseGener ator0 LS0=[Param.]<CR><LF> LineSource_Lin PulseGener Enumerati LS0?<CR><LF> ator1 For 12pin TTL out PulseGener ator2 PulseGener...
-
Page 66: Analog Control
EL-2800M-PMCL / EL-2800C-PMCL 2.4.7 Analog Control Acce Short DEFAUL Name Interface Values Description ASCII GA=[Param.]<CR><LF GainRawAnalogA (mono) I Integer min～0～max > GA?<CR><LF> (Bayer) FGA=[Param.]<CR><L GainRawDigitalA I Integer min～0～max -2393 3379 F> FGA?<CR><LF> PGR=[Param.]<CR><L GainRawDigitalR F> I Integer -4533 28400 min～0～max edAll PGR?<CR><LF>... - Page 67 EL-2800M-PMCL / EL-2800C-PMCL BLR1?<CR><LF> (Bayer model only) BLB1=[Param.]<CR>< BlackLevelRawTa LF> I Integer BLB1 -512 min～0～max p1 Blue BLB1?<CR><LF> (Bayer model only) BL2=[Param.]<CR><L BlackLevelRawTa I Integer -512 min～0～max F> p2All BL2?<CR><LF> BLR2=[Param.]<CR>< BlackLevelRawTa LF> I Integer BLR2 min～0～max -512 p2 Red BLR2?<CR><LF>...
-
Page 68: Lut Control
EL-2800M-PMCL / EL-2800C-PMCL 2.4.8 LUT Control Acce Short DEFAUL Name Interface Values Description ASCII Param 1: LUT index Param 2:LUTdata(Min LUTValueRed I Integer LUTR 4095 ～Max) (Bayer model only) LUT*=[Param1],[Para Param 1: LUT index γ=1 m2]<CR><LF> Param 2:LUTdata(Min LUTValueGreen I Integer... -
Page 69: Jai-Custom
EL-2800M-PMCL / EL-2800C-PMCL 2.4.11 JAI-Custom Interfac Short DEFA Name Values Description ASCII BMW=[Param.]<CR> BlemishWhiteE 0: False <LF> nable Boolean 1: True BMW?<CR><LF> BlemishWhite BMRC BMRCW=0<CR><LF Detect Command > BlemishWhite BMTHW=[Param.]<C BMTH Detect I Integer R><LF> Threshold BMTHW?<CR><LF> Param 1: Blemish... - Page 70 EL-2800M-PMCL / EL-2800C-PMCL SequenceMode SQF4=[Param.]<CR> Frame I Integer SQF4 Min～Max <LF> Count3 SQI4?<CR><LF> SequenceMode SQF5=[Param.]<CR> Frame I Integer SQF5 Min～Max <LF> Count4 SQI5?<CR><LF> SequenceMode SQF6=[Param.]<CR> Frame I Integer SQF6 Min～Max <LF> Count5 SQI6?<CR><LF> SequenceMode SQF7=[Param.]<CR> Frame I Integer SQF7 Min～Max <LF>...
- Page 71 EL-2800M-PMCL / EL-2800C-PMCL SQH4=[Param.]<CR> SequenceMode I Integer SQH4 Min～Max 1440 1440 <LF> Height3 SQH4?<CR><LF> SQH5=[Param.]<CR> SequenceMode I Integer SQH5 Min～Max 1440 1440 <LF> Height4 SQH5?<CR><LF> SQH6=[Param.]<CR> SequenceMode I Integer SQH6 Min～Max 1440 1440 <LF> Height5 SQH6?<CR><LF> SQH7=[Param.]<CR> SequenceMode I Integer SQH7 Min～Max...
- Page 72 EL-2800M-PMCL / EL-2800C-PMCL SQGA4?<CR><LF> Bayer) SQGA5=[Param.]<C SequenceMode (mono) I Integer SQGA5 Min～Max R><LF> Gain4 SQGA5?<CR><LF> (Bayer) SQGA6=[Param.]<C SequenceMode (mono) I Integer SQGA6 Min～Max R><LF> Gain5 SQGA6?<CR><LF> (Bayer) SQGA7=[Param.]<C SequenceMode (mono) I Integer SQGA7 Min～Max R><LF> Gain6 SQGA7?<CR><LF> (Bayer) SQGA8=[Param.]<C SequenceMode...
- Page 73 EL-2800M-PMCL / EL-2800C-PMCL (Mono model only) SQHB4=[Param.]<CR SequenceMode 1: Hbinning = OFF ><LF> Enumera SQHB4 Hbinning3 2: Hbinning = ON SQHB4?<CR><LF> tion (Mono model only) SQHB5=[Param.]<CR SequenceMode 1: Hbinning = OFF ><LF> Enumera SQHB5 Hbinning4 2: Hbinning = ON SQHB5?<CR><LF>...
- Page 74 EL-2800M-PMCL / EL-2800C-PMCL SQVB9=[Param.]<CR SequenceMode 1: Hbinning = OFF ><LF> Enumera SQVB9 Vbinning8 2: Hbinning = ON SQVB9?<CR><LF> tion (Mono model only) SQVB10=[Param.]<C SequenceMode SQVB1 1: Hbinning = OFF R><LF> Enumera Vbinning9 2: Hbinning = ON SQVB10?<CR><LF> tion (Mono model only) SQLUT1=[Param.]<C...
- Page 75 EL-2800M-PMCL / EL-2800C-PMCL SQBL9=[Param.]<CR SequenceMode I Integer SQBL9 -256 Min～Max ><LF> BlackLevel8 SQBL9?<CR><LF> SQBL10=[Param.]<C SequenceMode SQBL1 I Integer -256 Min～Max R><LF> BlackLevel9 SQBL10?<CR><LF> SQPGR1=[Param.]<C SequenceMode SQPGR R><LF> I Integer -4533 17713 Min～Max GainRed0 SQPGR1?<CR><LF> (Bayer model only) SQPGR2=[Param.]<C SequenceMode SQPGR R><LF>...
- Page 76 EL-2800M-PMCL / EL-2800C-PMCL (Bayer model only) SQPGB5=[Param.]<C SequenceMode SQPGB R><LF> I Integer -4533 17713 Min～Max GainBlue4 SQPGB5?<CR><LF> (Bayer model only) SQPGB6=[Param.]<C SequenceMode SQPGB R><LF> I Integer -4533 17713 Min～Max GainBlue5 SQPGB6?<CR><LF> (Bayer model only) SQPGB7=[Param.]<C SequenceMode SQPGB R><LF> I Integer...
- Page 77 EL-2800M-PMCL / EL-2800C-PMCL 5=Limit. 6= Trig is not set as Normal. 0: Off 1: RCT TRGOP=[Param.]<CR TRGO TriggerOption Enumera 2: PIV ><LF> tion 3: Smear-less TRGOP?<CR><LF> 4: RCT Continuous AGCF=[Param.]<CR> AlcReference I Integer AGCF Min～Max[%] <LF> AGCF?<CR><LF> AGCGA=[Param.]<CR AGCG GainAutoMax I Integer Min～Max...
- Page 78 EL-2800M-PMCL / EL-2800C-PMCL ALCChannelAr ALCML Enumera 0: Off / 1: On MidLowLeft tion ALCChannelAr ALCM Enumera 0: Off / 1: On MidHighRight tion ALCChannelAr ALCM Enumera 0: Off / 1: On MidHighMidRig tion ALCChannelAr ALCM Enumera 0: Off / 1: On...
- Page 79 EL-2800M-PMCL / EL-2800C-PMCL AWBChannelAr AWBM Enumera 0: Off / 1: On MidHighMidRig tion AWBChannelAr AWBM Enumera 0: Off / 1: On MidHighMidLef tion AWBChannelAr AWBM Enumera 0: Off / 1: On MidHighLeft tion AWBChannelAr AWBH Enumera 0: Off / 1: On...
- Page 80 EL-2800M-PMCL / EL-2800C-PMCL Minimum value and Maximum value are different depending on PirisLensSelect value PirisCurrentFv Enumera Same as above. PCV?<CR><LF> alue tion AR=[Param.]<CR><L F> AR?<CR><LF> AcquisitionFra I Integer Min～Max 325786 Maximum value is meLine calcurated depending on Height and Offset Y settings GMA=[Param.]<CR>...
- Page 81 EL-2800M-PMCL / EL-2800C-PMCL PGRPT0?<CR><LF> PGRPT1=[Param.]<C GpioPulseGen PGRPT I Integer Min～Max R><LF> Repeat Count1 PGRPT1?<CR><LF> PGRPT2=[Param.]<C GpioPulseGen PGRPT I Integer Min～Max R><LF> Repeat Count2 PGRPT2?<CR><LF> PGRPT3=[Param.]<C GpioPulseGen PGRPT I Integer Min～Max R><LF> Repeat Count3 PGRPT3?<CR><LF> 0: Free Run 1: Level High PGCM0=[Param.]<C...
- Page 82 EL-2800M-PMCL / EL-2800C-PMCL tion PGIN1?<CR><LF> PGIN2=[Param.]<CR GpioPulseGenI Enumera PGIN2 Same as above. ><LF> nput2 tion PGIN2?<CR><LF> PGIN3=[Param.]<CR GpioPulseGenI Enumera PGIN3 Same as above. ><LF> nput3 tion PGIN3?<CR><LF> PGIN0=[Param.]<CR GpioPulseGenI PGINV 0:Non-Inv Enumera ><LF> nvert0 1:Inv tion PGIN0?<CR><LF> PGIN1=[Param.]<CR GpioPulseGenI PGINV Enumera Same as above.
- Page 83 EL-2800M-PMCL / EL-2800C-PMCL ND1INV2=[Param.]< GpioNand1Inp ND1IN Enumera Same as above. CR><LF> utInvert2 tion ND1INV2?<CR><LF> 0: Stop MLI=[Param.]<CR><L MotorLensIris Enumera 1: Open F> tion 2: Close MLI?<CR><LF> 0: Stop MLZ=[Param.]<CR>< MotorLensZoo Enumera 1: Wide LF> tion 2: Tele MLZ?<CR><LF> 0: Stop MLF=[Param.]<CR><...
-
Page 84: Appendix 2
EL-2800M-PMCL / EL-2800C-PMCL Appendix 2 1. Precautions Personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive components. -
Page 85: Caution When Mounting The Camera
5. Exportation When exporting this product, please follow the export regulation of your own country. 6. References This manual and a datasheet for EL-2800M-PMCL / EL-2800C-PMCL can be downloaded from www.jai.com JAI SDK software can be downloaded from www.jai.com - 83 -... -
Page 86: Manual Change History
EL-2800M-PMCL / EL-2800C-PMCL Manual change history Date Revision Changes June 2013 New release July 2013 Correct typo in Table 2 and Table 3 July 2013 Change the description of AUX connectors Aug. 2013 Revised specifications SNR and sensitivity, Add EMVA 1288 measurement specifications, Correct timing figures Aug. -
Page 87: User's Record
Company and product names mentioned in this manual are trademarks or registered trademarks of their respective owners. JAI A-S cannot be held responsible for any technical or typographical errors and reserves the right to make changes to products and documentation without prior notification.