Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
Be aware of running machinery. Never operate under the dust hazards associated with each workpiece influence of drugs or alcohol, when tired, or when material, and always wear a NIOSH-approved distracted. respirator to reduce your risk. G0529 Oscillating Spindle & Disc Sander...
Page 5
Contact our Technical Support Department at around flammables, or in poorly-lit areas. Keep (570) 546-9663. work area clean, dry, and well lighted to mini- mize risk of injury. G0529 Oscillating Spindle & Disc Sander...
2: introduction foreword contact info We are proud to offer the Model g0529 oscillating We stand behind our machines. if you have any Spindle & disc Sander. this machine is part of service questions or parts requests, please call or a growing grizzly family of fine woodworking write us at the location listed below.
3: circuit reQuirements 110v operation power connection device the Model g0529 comes with a 5-15 plug, similar to figure 1, to connect the machine to power. GROUNDED serious personal injury could occur if you 5-15 RECEPTACLE connect the machine to power before com- pleting the setup process.
Weight load oil to protect them from corrosion during ship- the Model g0529 weighs 166 lbs. and has a ment. remove this protective coating with a sol- " X 16 " footprint. Most shop floors should vent cleaner or citrus-based degreaser such as be sufficient to carry the weight of the machine.
Model g0529 Sander mounts on a sturdy this section will cover the basic assembly and cabinet stand. adjustment instructions needed to begin opera- tion. Complete the assembly in the order provided to assemble the cabinet stand:...
90˚ from the edge of the sanding sleeve as shown in figure 10. adjust the pointer to 90˚. figure 8. installing table inserts. figure 10. Squaring the table and spindle. G0529 Oscillating Spindle & Disc Sander -13-...
12. note—This can be done with the sandpa- per installed, although it is somewhat easier to measure if the disc does not have the sandpaper disc installed. -14- G0529 Oscillating Spindle & Disc Sander...
NOT turn figure 13. the disc sander on at this point. repeat steps 1-3 if the sandpaper touches table at any point in the rotation. figure 13. installing pSa sanding disc. G0529 Oscillating Spindle & Disc Sander -15-...
6: operations power switch general the Model g0529 sander is equipped with a this section covers basic disc sanding opera- paddle-type power switch with a safety key. tions. please read the remaining portion of the manual before attempting any type of operation.
This will keep the workpiece from flying out of your hands from the rotational forces. figure 19. disc sanding with miter. figure 18. disc sanding with table tilted. G0529 Oscillating Spindle & Disc Sander -19-...
• Wipe a lubricant such as Slipit onto ® the table. • all the bearings are permanently lubricated and require no further lubri- cation long-term storage • Keep unpainted surfaces rust free with products such as Boeshield ® t-9. -20- G0529 Oscillating Spindle & Disc Sander...
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0529 OSCILLATING SPINDLE / 12" DISC SANDER Product Dimensions: Weight................................166 lbs. Width (side-to-side) x Depth (front-to-back) x Height................32 x 18 x 47 in.
Page 25
The information contained herein is deemed accurate as of 6/19/2014 and represents our most recent product specifications. Model G0529 PAGE 2 OF 2 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. G0529 Oscillating Spindle & Disc Sander -23-...
1. use a coarser grit sanding sleeve/disc. piece. 2. using too much pressure. 2. reduce pressure on workpiece while sanding. 3. Work held still for too long. 3. do not keep workpiece in one place for too long. G0529 Oscillating Spindle & Disc Sander -29-...
Page 32
1. not supporting the workpiece against the 1. use back stop to support workpiece. ly gets pulled out of stop. your hand. 2. Starting the workpiece on a leading corner. 2. Start workpiece on a trailing corner. -30- G0529 Oscillating Spindle & Disc Sander...
Page 33
Do you think your machine represents a good value? _____ Yes _____No Would you recommend Grizzly Industrial to a friend? _____ Yes _____No Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than 3 times.
Page 34
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.