Related Manuals for Advantech PCE-5126
Summary of Contents for Advantech PCE-5126
- Page 1 User Manual PCE-5126 LGA1155 ® ® Intel Core™i7/i5/i3/Pentium ® Xeon PICMG 1.3 Single Host Board with (ECC) DDR3 / Dual GbE LAN...
- Page 2 Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe- ments of the rights of third parties, which may result from its use. Acknowledgements AMIBIOS is a trademark of American Megatrends Inc. ® ® ®...
-
Page 3: Declaration Of Conformity
In addition, free technical support is available from Advantech engineers every busi- ness day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products. PCE-5126 User Manual... - Page 4 Memory Compatibility PCE-5126 Memory Tested for Compatibility Brand Size Speed ECC Vendor PN Advantech PN Memory DDR3 TS128MLK64V1U / 96D3-1G1066NN- SEC K4B1G0846D- 1066 TS2KNU28100-1S HCF8 (128x8) SEC K4B1G0846D DDR3 96D3-1G1066NN- TS128MLK64V1U HCH9 ENJ038A3 1066 (128x8) DDR3 TS256MLK64V1U / 96D3-2G1066NN- SEC K4B1G0846D-...
-
Page 5: Processor Support
Yes (Except PCE-7B10-04A1E) Note! If PCE-5126 is used on different backplanes which has different PCIe configuration. Below message would be showed on first time power on, and user has to turn off AC power and then turn on for PCIe re-configu- ration. - Page 6 It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the PCE-5126, check it for signs of ship- ping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our service department or your local sales representative immediately.
-
Page 7: Table Of Contents
Table 1.2: Connector list.............. 5 Board Layout: Jumper and Connector Locations........6 Figure 1.1 Jumper and connector locations......... 6 PCE-5126 Block Diagram ................. 7 Figure 1.2 PCE-5126 block diagram..........7 Safety Precautions ..................8 Jumper Settings ..................8 1.8.1 How to set jumpers ............... 8 1.8.2... - Page 8 Figure 3.27Save & Exit............... 49 Chapter Value-Added Software Services ..51 Value-Added Software Services ............. 52 4.1.1 Software API................52 4.1.2 Software Utility................53 Chapter Chipset Software Installation Utility Before You Begin..................56 Introduction ..................... 56 PCE-5126 User Manual viii...
- Page 9 Table B.11:HDD LED (JFP2 / HDDLED) ........78 B.12 ATX Soft Power Switch (JFP1 / PWR_SW) ..........78 Table B.12:ATX soft power switch (JFP1 / PWR_SW) ....78 B.13 Hi-definition Audio Link Connector (HDAUD1)........78 Table B.13:Hi-definition audio link connector (HDAUD1) ... 78 PCE-5126 User Manual...
- Page 10 Table B.20:1st MB memory map ..........82 B.21 PCI Bus Map................... 82 Table B.21:PCI bus map............. 82 Appendix C Programming the GPIO ....83 Supported GPIO Register ............... 84 GPIO registers ..................84 GPIO example program-1............... 84 PCE-5126 User Manual...
-
Page 11: Chapter 1 Hardware Configuration
Chapter Hardware Configuration... -
Page 12: Introduction
Introduction PCE-5126 is a PICMG 1.3 form-factor single host board which is designed with Intel®B65/Q67/C206 PCH for industrial applications that need high computing power and strong I/O capability. PCE-5126 supports 32nm manufacturing technology, LGA1155 socket Intel® CoreTM i7/i5/i3, Pentium® and XeonTM processors that inte- grate memory and graphic controllers and supports DDR3 1333 MHz SDRAM up to 8GB. -
Page 13: Specifications
SATA hard disk drive interface: Two SATA3 (600MB/s) are with blue connec- tors and four SATA2 (300MB/s) are with black connectors. These interfaces can be enabled/disabled in the BIOS. Note! PCE-5126 does NOT support PATA(IDE) interface. 1.3.2 Memory RAM: –... -
Page 14: Input/Output
Power consumption: Processor: Intel Core i7-2600; Memory: 2 DDR3 1333 MHz 2 GB DIMMs Voltage +12 V +5 V +3.3 V +5 V Current 6.65A 1.62A 1.98A 0.73A Board size: 338.58 mm (L) x 126.39 mm (W) (13.3" x 4.98") Board weight: 0.490 kg PCE-5126 User Manual... -
Page 15: Jumpers And Connectors
Jumpers and Connectors Connectors on the PCE-5126 single host board link it to external devices such as hard disk drives and a keyboard. In addition, the board has a number of jumpers used to configure your system for your application. -
Page 16: Board Layout: Jumper And Connector Locations
CPU Socket DIMMA1 Memory connector channel A DIMMB1 Memory connector channel B GPIO1 GPIO pin header (SMD pitch-2.0 mm) LPC1 COM port module expansion pin-header Board Layout: Jumper and Connector Locations Figure 1.1 Jumper and connector locations PCE-5126 User Manual... -
Page 17: Pce-5126 Block Diagram
PCE-5126 Block Diagram Figure 1.2 PCE-5126 block diagram PCE-5126 User Manual... -
Page 18: Safety Precautions
1, 2 and 3. In this case you connect either pins 1 and 2, or 2 and 3. A pair of needle-nose pliers may be useful when set- ting jumpers. PCE-5126 User Manual... -
Page 19: Bios Cmos/Me Data Clear (Jcmos1/Jmeclr1)
1.8.2 BIOS CMOS/ME data clear (JCMOS1/JMECLR1) The PCE-5126 CPU card contains a jumper that can erase BIOS CMOS data and ME (Intel Management Engine) data and reset the system BIOS information. Nor- mally this jumper should be set with pins 1-2 closed. If you want to reset those data, set JCMOS1/JMECLR1 to 2-3 closed for just a few seconds, and then move the jumper back to 1-2 closed. -
Page 20: Watchdog Timer Output (Jwdt1)
1.8.3 Watchdog timer output (JWDT1) The PCE-5126 contains a watchdog timer that will reset the CPU in the event the CPU stops processing. This feature means the PCE-5126 will recover from a soft- ware failure or an EMI problem. The JWDT1 jumper settings control the outcome of what the computer will do in the event the watchdog timer is tripped. -
Page 21: Memory Installation Procedures
1.11 Cache Memory CPUs supported by PCE-5126 have 8 MB, 6 MB, 3 MB L2 cache memory sizes. 1.12 Processor Installation Warning! Without a fan or heat sink, the processor will overheat and cause dam- age to both the processor and the single board computer. - Page 22 Remove the socket protection cap. Align the cuts on the processor with the edges of the socket. Replace the socket cap; lower the retainer bar and clip it shut. PCE-5126 User Manual...
-
Page 23: Processor Cooler Installation
Advantech offers a specially designed CPU cooler for PCE-5126 for better heat dissi- pation efficiency and enhancing rigidity of CPU card, part number 1960047831N001. Buy it for PCE-5126 CPU card since it is NOT compatible with other brand CPU cool- ers (neither is it compatible with Intel boxed CPU cooler). - Page 24 PCE-5126 User Manual...
-
Page 25: Chapter 2 Connecting Peripherals
Chapter Connecting Peripherals... -
Page 26: Introduction
LPT1. USB Ports (USB12, USB34, USB56, USB78) The PCE-5126 provides up to 9 USB (Universal Serial Bus) on-board ports with com- plete Plug & Play and hot swap support for up to 127 external devices. These USB ports comply with USB Specification Rev. 2.0, support transmission rates up to 480 Mbps and are fuse protected. -
Page 27: Vga Connectors (Vga1)
VGA Connectors (VGA1) The PCE-5126 has VGA outputs that can drive conventional CRT displays. VGA1 is a standard 15-pin D-SUB connector commonly used for VGA. Serial Ports (COM1 & COM2) The PCE-5126 offers two serial ports. These ports can connect to serial devices, such as a mouse or a printer, or to a communications network. -
Page 28: Ps/2 Keyboard And Mouse Connector (Kbms1/Kbms2)
The on-board KBMS2 pin header provides connection the front panel PS/2 keyboard and mouse connector of the chassis. CPU Fan Connector (CPUFAN1) This connector supports cooling fans of 500 mA (6 W) or less, and it also supports smart fan control when using 4-pin cooler. PCE-5126 User Manual... -
Page 29: Front Panel Connectors (Jfp1, Jfp2 & Jfp3)
Front Panel Connectors (JFP1, JFP2 & JFP3) There are several external switches to monitor and control the PCE-5126. 2.8.1 Power LED and keyboard lock (JFP3) JFP3 is a 5-pin connector for the power LED. Refer to Appendix B for detailed infor- mation on the pin assignments. -
Page 30: External Speaker (Jfp2)
2.8.2 External speaker (JFP2) JFP2 is a 4-pin connector for an external speaker. The PCE-5126 provides an onboard buzzer as an alternative to an external speaker. To enable the buzzer, set pins 3 and 4 as closed. 2.8.3 Reset connector (JFP1) Many computer cases offer the convenience of a reset button. -
Page 31: H/W Monitor/Watchdog Timer/Infrared
Open: Disables OBS Alarm 2.9.2 Watchdog Timer (JWDT1) This is for setting action trigger by watchdog timer. 1-2 Pin Close: No Action 2-3 Pin Close: System Reset 2.9.3 Infrared Interface (JIR1) This is a 5-pin header for an infrared device. PCE-5126 User Manual... -
Page 32: Lan Ports (Lan1 & Lan2)
LAN Ports (LAN1 & LAN2) LED2 LED1 The PCE-5126 is equipped with one or two high-performance 1000 Mbps Ethernet LANs. They are supported by all major network operating systems. The RJ-45 jacks on the rear plate provide convenient connectivity. Table 2.2: LAN LED Indicators... -
Page 33: High Definition Audio Module Interface (Hdaud1)
2.11 High Definition Audio Module Interface (HDAUD1) This HDAUD1 pin header is the connection interface to Advantech's 7.1 channel high definition audio module. Note! Advantech 7.1 channel high definition audio module ordering informa- tion. P/N: PCA-AUDIO-HDA1E PCE-5126 User Manual... -
Page 34: Figure 2.1 Jumper And Connector Locations Of Pca-Audio Hda1E
CPU card with the HD audio cable (PN:1701120251) Figure 2.1 Jumper and connector locations of PCA-AUDIO-HDA1E Note! Please remove the yellow jumper cap on the CPU card's HDAUD1 pin- header before connecting the HD audio cable to it. PCE-5126 User Manual... -
Page 35: Gpio Header (Gpio1)
Appendix C. 2.13 Case Open Connector (JCASE1) The 2-pin case open connector is for chassis with a case open sensor. When the case is open, the buzzer on motherboard will beep. PCE-5126 User Manual... -
Page 36: Front Panel Lan Indicator Connector (Lanled1)
LED1 LED2 1000Mbps Link On Green On 1000Mbps Active Green on Flash 1000Mbps Link Off 100Mbps Link On Orange On 100Mbps Active Orange On Flash 100Mbps Link Off 10Mbps Link On 10Mbps Active Flash 10Mbps Link Off PCE-5126 User Manual... -
Page 37: Serial Ata Interface (Sata1~Sata6)
2.15 Serial ATA Interface (SATA1~SATA6) The PCE-5126 features high performance serial ATA interface (2* 600MB/s and 4* 300MB/s) which eases cabling to hard drivers or CD/DVD drivers with long cables. These six on-board SATA ports can be configured as RAID 0, 1, 10, or 5. Please see the detailed BIOS setting instructions for this in Chapter 3. - Page 38 PCE-5126 User Manual...
-
Page 39: Ami Bios Setup
Chapter AMI BIOS Setup... -
Page 40: Introduction
The Setup program uses a number of menus for making changes and turning the special features on or off. This chapter describes the basic navigation of the PCE-5126 setup screens. Figure 3.1 Setup program initial screen AMI’s BIOS ROM has a built-in Setup program that allows users to modify the basic... -
Page 41: Entering Setup
Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time must be entered in HH:MM:SS format. PCE-5126 User Manual... -
Page 42: Advanced Bios Features Setup
3.2.2 Advanced BIOS Features Setup Select the Advanced tab from the PCE-5126 setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the <Arrow>... -
Page 43: Figure 3.4 Advantech Bios Update V1.2
Figure 3.4 Advantech BIOS Update V1.2 You can update BIOS from UPDATE.BIN file in FAT32 storage device 3.2.2.2 ACPI Settings Figure 3.5 ACPI Settings Power Type Choose this item correspond with your power supply type ATX or AT. PCE-5126 User Manual... -
Page 44: Figure 3.6 Tpm Configuration
PowerOn by Modem "Enabled" or "Disabled" PowerOn by Modem 3.2.2.3 TPM Configuration Figure 3.6 TPM Configuration TPM Support "Enable or disable" TPM Support. You can purchase Advantech LPC TPM mod- ule to enable TPM function. P/N: PCA-TPM-00A1E PCE-5126 User Manual... -
Page 45: Figure 3.7 Cpu Configuration
CPU Configuration Figure 3.7 CPU Configuration Figure 3.8 Socket 0 CPU Information Active Processor Core Use this to select how many processor cores you want to activate when you are using a dual or quad core processor. PCE-5126 User Manual... -
Page 46: Figure 3.9 Sata Configuration
Default is "Energy Efficient". User can set "EIST", "Turbo Mode", “P-STATE", "C3", "C6" and "Package C State Limit" at "CUSTOM Mode" 3.2.2.5 SATA Configuration Figure 3.9 SATA Configuration SATA Mode This can be configured as IDE, RAID, AHCI, or Disabled. PCE-5126 User Manual... -
Page 47: Figure 3.10Intel Igd Swsci Opregion Configuration
IGD - Boot Type Select the Video Device which will be activated during POST. This has no effect if external graphics present. There are three options, [Auto]/[CRT]/[DVI]. (DVI is optional). Spread Spectrum Clock "Enable or Disable" Spread Spectrum Clock. PCE-5126 User Manual... -
Page 48: Figure 3.11Intel Trusted Execution Technology Configuration
3.2.2.7 Intel Trusted Execution Technology Configuration Figure 3.11 Intel Trusted Execution Technology Configuration Intel Trusted Execution Technology Configuration This enables or disables Intel® Trusted Execution Technology 3.2.2.8 USB Configuration Figure 3.12 USB Configuration PCE-5126 User Manual... -
Page 49: Figure 3.13Amt Configuration
* This item will change wording which depends on what USB storage device you plug. 3.2.2.9 AMT Configuration Figure 3.13 AMT Configuration "Enable or Disable" Intel Advance Management Technology Unconfigure AMT/ME "Enable or Disable" Unconfigure AMT/ME WatchDog Timer "Enable or Disable" Watchdog Timer PCE-5126 User Manual... -
Page 50: Figure 3.14Super Io Configuration
3.2.2.10 Super IO Configuration Figure 3.14 Super IO Configuration Figure 3.15 Serial Port 1 Configuration PCE-5126 User Manual... -
Page 51: Figure 3.16Serial Port 2 Configuration
Figure 3.16 Serial Port 2 Configuration Figure 3.17 Parallel Configuration Serial Port "Enable or Disable" Serial Port Parallel Port "Enable or Disable" Parallel Port PCE-5126 User Manual... -
Page 52: Figure 3.18Pc Health Status
Use this to set the ACPI shutdown temperature threshold. When the system reaches the shutdown temperature, it will be automatically shut down by ACPI OS to protect the system from overheating damage. CPUFAN Mode Setting "Enable or Disable" CPUFAN Mode to SMART FAN setting PCE-5126 User Manual... -
Page 53: Chipset
3.2.3 Chipset Figure 3.19 Chipset 3.2.3.1 North Bridge Figure 3.20 North Bridge Low MMIO Align Low MMIO resources align at 64MB/1024MB. PCE-5126 User Manual... -
Page 54: Figure 3.21South Bridge
SMBus Controller "Enable or Disable" SMBus Controller. LAN2 Controller "Enable or Disable" LAN2 Controller. LAN Option-ROM "Enable or Disable" LAN Option-ROM. Wake on LAN from S5 "Enable or Disable" Wake on LAN from S5. PCE-5126 User Manual... -
Page 55: Figure 3.22Usb Configuration
“Restore AC Power Loss“ is set to “power off“. 3.2.3.3 USB Configuration Figure 3.22 USB Configuration All USB Devices "Enable or Disable" All USB Devices. EHCI Controller #1 & #2 "Enable or Disable" EHCI Controller #1 or #2. PCE-5126 User Manual... -
Page 56: Figure 3.23Me Subsystem
"Enable or Disable" End of Post Message. Execute MEBx "Enable or Disable" Execute MEBx to show "Ctrl+P" to enter ME setup during post screen MEBx Mode "Normal, Hidden Ctrl+P, Enter MEBx Setup" to use ME setup PCE-5126 User Manual... -
Page 57: Figure 3.24Chipset Reference Board
3.2.3.5 Chipset Reference Board Figure 3.24 Chipset Reference Board CIRA Trigger "Enable or Disable" CIRA Trigger. 3.2.4 Boot Figure 3.25 Boot PCE-5126 User Manual... -
Page 58: Security
Security Figure 3.26 Security Select Security Setup from the PCE-5126 Setup main BIOS setup menu. All Security Setup options, such as password protection and virus protection are described in this section. To access the sub menu for the following items, select the item and press <Enter>... -
Page 59: Save & Exit
Discard changes and Reset Select this option to quit Setup and reset computer without making any permanent changes to the system configuration. Save Changes Select this option to save your changes. Discard Changes Select this option to discard your changes. PCE-5126 User Manual... - Page 60 This option allows you to attempt to launch the EFI Shell application (shellx64.efi) from one of the available file system devices. *When you do some critical changes, the system will still reboot even you choose "Save changes and exit". PCE-5126 User Manual...
-
Page 61: Value-Added Software Services
Chapter Value-Added Software Services... -
Page 62: Value-Added Software Services
(restarting the system) after a certain number of seconds. Hardware Monitor The Hardware Monitor (HWM) API is a system health super- vision API that inspects certain condition indexes, such as fan speed, temperature and voltage. PCE-5126 User Manual... -
Page 63: Software Utility
OS crash. It will diagnose the hardware sta- tus, and then send an e-mail to a designated administrator. The eSOS also provides remote connection: Telnet server and FTP server, allowing the administrator to rescue the sys- tem. Note: This function requires BIOS customization. PCE-5126 User Manual... - Page 64 PCE-5126 User Manual...
-
Page 65: Chipset Software Installation Utility
Chapter Chipset Software Installation Utility... -
Page 66: Before You Begin
To facilitate the installation of the enhanced display drivers and utility software, read the instructions in this chapter carefully. The drivers for the PCE-5126 are located on the software installation CD. The driver in the folder of the driver CD will guide and link you to the utilities and drivers under a Windows system. -
Page 67: Windows® Xp / Windows® 7 Driver Setup
Navigate to the "01-Chipset" folder and click "infinst_autol.exe" to complete the installation of the driver. Note! Wrong driver installation may cause unexpected system instability. The drivers on this CD support both Windows XP 32-bit /64-bit and Win- dows 7 32-bit/64-bit. PCE-5126 User Manual... - Page 68 PCE-5126 User Manual...
-
Page 69: Chapter 6 Integrated Graphic Device Setup
Chapter Integrated Graphic Device Setup... -
Page 70: Introduction
Insert the driver CD into your system’s CD-ROM drive. You can see the driver folder items. Navigate to the "VGA" folder and click "setup.exe" to complete the installation of the driver. Note! Wrong driver installation may cause unexpected system instability. PCE-5126 User Manual... -
Page 71: Chapter 7 Lan Configuration
Chapter LAN Configuration... -
Page 72: Introduction
Introduction The PCE-5126 has dual Gigabit Ethernet LANs via dedicated PCI Express x1 lanes (Intel 82579LM (LAN1) and 82583V (LAN2 of QG2) or 82574L (LAN2 of WG2) that offer bandwidth of up to 500 MB/sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet at 1000 Mbps. -
Page 73: Chapter 8 Sata Raid Setup
Chapter SATA RAID Setup... -
Page 74: Introduction
Before you install the Intel® Matrix Storage Manager, please read the "readme.txt" which is in the folder “Others\RAID”. The driver is in the CD’s “Others\RAID” folder.You may go to the directory of the CD and follow Intel's installation guide to install the driver and utility. PCE-5126 User Manual... -
Page 75: Appendix A Programming The Watchdog Timer
Appendix Programming the Watchdog Timer... -
Page 76: Introduction
Introduction The PCE-5126’s watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how to pro- gram it. -
Page 77: Table A.1: Watchdog Timer Registers
Write 1 to bit 4: Watchdog timer count mode is 1000 times faster. If bit 3 is 0, the count mode is 1/1000 seconds mode. If bit 3 is 1, the count mode is 1/1000 minutes mode. PCE-5126 User Manual... -
Page 78: Example Program
; Enable the function of watchdog timer al,30h dx,al al,dx al,01h dx,al ;----------------------------------------------------------- Dec dx ; Set second as counting unit al,0f5h dx,al al,dx And al,not 08h dx,al ;----------------------------------------------------------- Dec dx ; Set timeout interval as 10 seconds and start counting al,0f6h PCE-5126 User Manual... - Page 79 ;----------------------------------------------------------- Dec dx ; Set minute as counting unit al,0f5h dx,al al,dx al,08h dx,al ;----------------------------------------------------------- Dec dx ; Set timeout interval as 5 minutes and start counting al,0f6h dx,al al,5 ; 5 minutes dx,al ;----------------------------------------------------------- PCE-5126 User Manual...
- Page 80 ;----------------------------------------------------------- Dec dx ; Lock NCT6776F al,0aah dx,al Enable watchdog timer to be reset by keyboard ;----------------------------------------------------------- Mov dx,2eh ; Unlock NCT6776F Mov al,87h Out dx,al Out dx,al ;----------------------------------------------------------- Mov al,07h ; Select registers of watchdog timer PCE-5126 User Manual...
- Page 81 Out dx,al Out dx,al ;----------------------------------------------------------- Mov al,07h ; Select registers of watchdog timer dx,al al,08h dx,al ;----------------------------------------------------------- Dec dx ; Enable the function of watchdog timer al,30h dx,al al,01h dx,al ;----------------------------------------------------------- Dec dx ; Generate a time-out signal PCE-5126 User Manual...
- Page 82 ;Write 1 to bit 5 of F7 register al,dx Or al,20h dx,al ;----------------------------------------------------------- Dec dx ; Lock NCT6776F al,0aah dx,al PCE-5126 User Manual...
-
Page 83: Appendix B I/O Pin Assignments
Appendix I/O Pin Assignments... -
Page 84: Parallel Port Connector (Lpt1)
Parallel Port Connector (LPT1) Table B.1: Parallel port connector (LPT1) Signal Signal STROBE* AUTOFD* INIT* SLCTINI* ACK* BUSY SLCT * low active VGA Connector (VGA1) Table B.2: VGA connector (VGA1) Signal Signal GREEN BLUE H-SYNC V-SYNC PCE-5126 User Manual... -
Page 85: Rs 232 Serial Port (Com2)
RS 232 Serial Port (COM2) Table B.3: RS-232 serial port (COM2) Signal SOUT USB Header (USB12 ~ 78) Table B.4: USB Header (USB12 ~ 78) Signal Signal USB1_VCC5 USB2_D+ USB2_VCC5 USB1_D- USB2_D- USB1_D+ PCE-5126 User Manual... -
Page 86: Ps/2 Keyboard/Mouse Connector (Kbms1)
MS DATA KB CLOCK MS CLOCK External Keyboard Connector (KBMS2) Table B.6: External keyboard connector (KBMS2) Signal KBCLK KBDAT MSDAT MSVCC MSCLK CPU Fan Power Connector (CPUFAN1) Table B.7: CPU fan power connector (CPUFAN1) Signal +12V Detect PCE-5126 User Manual... -
Page 87: Power Led And Keyboard Lock Connector
SUPLED KEYLOCK# External Speaker Connector (JFP2 / SPEAKER) Table B.9: External speaker connector (JFP2 / SPEAKER) Signal SPK_CN17P1 SPK_CN17P2 SPK_CN17P3 SPK_CN17P4 B.10 Reset Connector (JFP1 / RESET) Table B.10: Reset connector (JFP1 / RESET) Signal RESET # PCE-5126 User Manual... -
Page 88: Hdd Led (Jfp2 / Hddled)
ATX Soft Power Switch (JFP1 / PWR_SW) Table B.12: ATX soft power switch (JFP1 / PWR_SW) Signal 5VSB PWR-BTN B.13 Hi-definition Audio Link Connector (HDAUD1) Table B.13: Hi-definition audio link connector (HDAUD1) Signal Signal ACZ_VCC ACZ_SYNC ACZ_BITCLK ACZ_SDOUT ACZ_SDIN0 ACZ_SDIN1 -ACZ_RST ACZ_12V PCE-5126 User Manual... -
Page 89: B.14 Sm Bus Connector (Jfp2 / Snmp)
SM Bus Connector (JFP2 / SNMP) Table B.14: SM bus connector (JFP2 / SNMP) Signal SMB_DATA SMB_CLK B.15 LAN1 and LAN2 LED Connector (LANLED1) Table B.15: LAN1 and LAN2 LED connector (LANLED1) Signal #LAN1_ACT #LAN2_ACT V33_AUX V33_AUX #LAN1_LINK1000 #LAN2_LINK1000 #LAN1_LINK100 #LAN2_LINK100 V33_AUX PCE-5126 User Manual... -
Page 90: B.16 Gpio Header (Gpio1)
B.16 GPIO Header (GPIO1) Table B.16: GPIO header (GPIO1) Signal SIO_GPIO0 SIO_GPIO4 SIO_GPIO1 SIO_GPIO5 SIO_GPIO2 SIO_GPIO6 SIO_GPIO3 SIO_GPIO7 VCC_GPIO PCE-5126 User Manual... -
Page 91: B.17 System I/O Ports
Com3-Com6 3F8-3FF Com1 2F8-2F0 Com2 4700-470F 600h-67Fh SMSC Secondary I/O used B.18 DMA Channel Assignments Table B.18: DMA channel assignments Channel Signal Available Available Floppy disk (8-bit transfer) Available Cascade for DMA controller 1 Available Available Available PCE-5126 User Manual... -
Page 92: B.19 Interrupt Assignments
REQ A PCI slot 2 AD30 INT C, D, A, B GNT B REQ B PCI slot 3 AD29 INT D,A,B,C GNT C REQ C PCI slot 4 AD28 INT A, B, C, D GNT D REQ D PCE-5126 User Manual... - Page 93 Appendix Programming the GPIO...
-
Page 94: C.1 Supported Gpio Register
MOV AL,87H OUT DX,AL OUT DX,AL --------------------------------------------------------------- Configure logical device, configuration register CRE0,CRE1,CRE2 --------------------------------------------------------------- MOV DX,2EH MOV AL,09H OUT DX,AC DEC DX MOV AL,30H OUT DX,AL INC DX IN AL,DX OR AL,10000000B DEC DX MOV AL,07H OUT DX,AL PCE-5126 User Manual... - Page 95 ;Set GPIO is normal not inverter OUT DX,AL; DEC DX MOV AL,E1H OUT DX,AL INC DX MOV AL,??H ; Put the output value into AL OUT DX,AL ------------------------------------------ Exit extended function mode | ------------------------------------------ MOV DX,2EH MOV AL,AAH OUT DX,AL PCE-5126 User Manual...
- Page 96 www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher.
Need help?
Do you have a question about the PCE-5126 and is the answer not in the manual?
Questions and answers