Chimney Components - Heatilator I60 Owner's Manual Installation And Operation

C. Chimney Components
The following pictures show only those chimney components which may be safely used with this fireplace.
Catalog # Description
US CAN
CAK5A CA- Chimney Air Kit
K5A
ID4 ID4 Insulated Duct/Outside Air
UD4 UD4 Uninsulated Duct/Outside Air
SL1106 SL406 Chimney Section - 6 in. (152 mm) long
SL1112 SL412 Chimney Section - 12 in. (305 mm)
long
SL1118 SL418 Chimney Section - 18 in. (457 mm)
long
SL1136 SL436 Chimney Section - 36 in. (914 mm)
long
SL1148 SL448 Chimney Section - 48 in. (1219 mm)
long
SL11 SL4 Chimney Stabilizer
SL1130 SL430 Chimney Offset/Return - 30 deg
FS538 FS538 Ceiling Firestop - Straight
FS540 FS540 Ceiling Firestop - 30 deg
AS10 AS10 Straight Attic Insulation Shield, 24 in.
(610 mm)
JB577 JB577 Chimney Joint Band
CB576 CB576 Chimney Bracket
RF570 RF570 Roof Flashing - Flat to 6/12 Pitch
RF571 RF571 Roof Flashing - 6/12 to 12/12 Pitch
TR11 TR444 Round Termination Cap
TR11T TR442 Round Telescoping Termination Cap
TCT1175 Terra Cotta Termination Cap
ST1175 ST475 Square Termination Cap
DTO134 Short Octagon Decorative Cap

DTO146 Tall Octagon Decorative Cap
DTS134 Short Square Decorative Cap
DTS146 Tall Square Decorative Cap
CT56 CT56 Chase Top
LDS33 LDS33 Decorative Shroud - 3 ft x 3 ft (.91 m
x .91 m)
LDS46 LDS46 Decorative Shroud - 4 ft x 6 ft (1.22 m
x 1.83 m)
LDS-BV LDS- Decorative Shroud - 26 in. x 26 in.
BV (660 mm x 660 mm)
Field Constructed Shrouds (See "Wood-
burning Termination Cap")
CT-11A n/a Adapter-May be used with the follow-
ing Copper Caps
n/a CT-Series
n/a DT-Series
14 in.
(356 mm)
5-1/4 in.
(133 mm)
13 in.
(330 mm)
CAK5A Chimney Air Kit
14 in.
(356 mm)
4 in. (102 mm)
SLA10 Adaptor
(Required in Canada)
Heatilator • I60, I80 • 4013-250 • Rev H • 1/11
ID4 Insulated Duct
42 in.
(1067 mm)
UD4 Uninsulated Duct
42 in.
(1067 mm)
11 in.
(279 mm)
Chimney Sections
Catalog #
US CAN in
SL1106 SL406 6
SL1112 SL412 12
SL1118 SL418 18
SL1136 SL436 36
SL1148 SL448 48
A = Actual Length
B = Effective Length (length of
chimney part after it has
been snapped to another)
20-3/4 in.
(527 mm)
18 in.
(457 mm)
SL11/SL4 Vent Stabilizer
4 in. (102 mm) i.d.
4 in. (102 mm) i.d.
A
13 in.
(330 mm)
B
A B
mm in mm
152 4-3/4 121
305 10-3/4 273
457 16-3/4 425
914 34-3/4 883
1219 46-3/4 1187
Inside Diameter
SL4 - 10 in. (254 mm)
SL11 - 11 in. (279 mm)
Outside Diameter
13 in. (330 mm)
49