Precautions For Installation - Panasonic WV-NW960 Installation Manual

Precautions for installation

All work related to the installation of this product
should be made by qualified service personnel or
system installers.
Power switch
• This product does not have a power switch. When
making the power supply work, create a procedure
to turn on/off the power of the camera. The power
will be turned on when the power plug is inserted
to an outlet. When the power is turned on, the cam-
era will automatically pan/tilt/adjust focus as the
startup operation.
When cleaning this product, unplug first.
• A grounding connection must be made before con-
necting the power cable to the main power supply.
When disconnecting the grounding wire, make
sure that the power cable of this product is discon-
nected from the main power supply.
Cautions for installation
Make sure that the installation area is strong enough to
hold the camera, such as a concrete ceiling.
• This product is designed to be used as a pendant
mount camera. When using after installing it tilted
or on desktop, it may not work correctly or its life-
time may be shorten.
• This product should be installed with making the
camera level. (The dome part should be down-
ward.)
• Be sure to remove this product if it is not in use.
Procure fixing screws locally.
Fixing screws to be used to fix this product are not pro-
vided.
Prepare them after considering the total weight, the
material and strength of the area where the camera is to
be installed.
When tightening fixing screws
Firmly tighten screws/bolts that are suited to fix with the
material and strength of the area where the camera is to
be installed. After tightening screws/bolts, check with
eyes if the camera is fixed firmly.
Avoid installing in the following locations.
• Locations where a chemical agent is used such as
a swimming pool
• Locations subject to steam and oil smoke such as
a kitchen
• Locations near flammable gas or vapor
• Locations where radiation or x-ray emissions are
produced
• Locations where it may be damaged by briny air
such as seashores
• Locations where corrosive gas is produced
• Locations where the temperature is not between
–40 °C - +50 °C {–40 °F - 122 °F}.
• Locations subject to vibrations (This product is not
designed for on-vehicle use.)
• Locations subject to condensation as the result of
severe changes in temperature (The dome cover
may be fogged or condensation may be formed.)
Remove the cover film from the transparent part of
the dome cover after the installation is complete.
When the exogenous noise can affect the product
performance
When wiring, make sure that the cables of this product
are at least 1 meter away from power cables of 100 V or
more such as a cable of electric light, or install cable
plumbing system with metal pipes to separate cables to
prevent noise affect. (Metal pipes should be grounded.)
Radio disturbance
When this product is used near a TV/radio antenna, or a
strong electric field or magnetic field (such as near a
motor, a transformer or a electrical power line), images
may be distorted and noise may be caused.
Install this product when humidity is low
When installing this product while humidity is high,
inside of the dome cover may be fogged.
About the anti-freeze heater
The antifreeze heater is featured for use in a cold
region. The antifreeze heater will automatically be
turned on when the internal temperature is 10 °C or
below. However, the antifreeze heater may not work
effectively when using this product under severe cir-
cumstances such where temperature is at –40 °C
{–40 °F}. When using this product in a cold region, try
not to use this product under severe circumstances
where temperature can be lower than –40 °C {–40 °F}.
Image quality disturbance
A wiper is not featured in this product. Image may be
not displayed or image quality may become low under
the following circumstances.
(1) When raining
When raining and winding, it may be possible that
images become unclear due to adhesion of rain-
drops to the dome cover.
(2) When snowing
When snowing and winding, it may be possible that
images become unclear due to adhesion of snow
to the dome cover.
(3) When the concentration of dust/smog in the air is
relatively high
When the concentration of dust/smog in the air is
relatively high, it may be possible that images
become unclear due to adhesion of dust/dirt to the
dome cover.
13