1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Security Camera
  5. WVNS954 - NETWORK CAMERA
  6. Operating instructions manual

Panasonic WV-NS954 Operating Instructions Manual

Panasonic operating instructions network camera wv-ns954, wv-nw964, wv-ns954, wv-nw964
Hide thumbs Also See for WV-NS954:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Manual

Network Camera

Operating Instructions

WV-NS954
Model Nos.
WV-NW964
WV-NS954
WV-NW964
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.

Advertisement

Table of Contents
loading

Related Manuals for Panasonic WV-NS954

Summary of Contents for Panasonic WV-NS954

  • Page 1: Network Camera

    Network Camera Operating Instructions WV-NS954 Model Nos. WV-NW964 WV-NS954 WV-NW964 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

  • Page 2: Table Of Contents

    Preface ... 3 About these operating instructions ... 3 Trademarks and registered trademarks ... 3 Viewer software ... 3 Monitor images on a PC ... 4 Monitor images from a single camera ... 4 Monitor images from multiple cameras ... 9 Record images on the SD memory card manually ...

  • Page 3: Preface

    Preface About these operating instructions There are 3 sets of operating instructions for the WV-NS954, WV-NW964 as follows. • Installation Guide • Operating instructions • Setup Instructions • WV-NS954 Network camera (for indoor use) • WV-NW964 Network camera (for outdoor use) * The screens used in these Setup Instructions show the case of WV-NS954.

  • Page 4: Monitor Images On A Pc

    Monitor images from a single camera Step 1 Start up the web browser. Step 2 Enter the IP address designated using the Panasonic IP setup software in the address box of the browser. (Example: http://192.168.0.10) Important: • When the HTTP port number is changed from "80", enter "http://IP address of the camera + : (colon) +...
  • Page 5 The refresh interval may be longer depending on a network environment, PC spec, photographic sub- ject, access traffic, etc. Refer to the following page for further information about the "Live" page. About the "Live" page q [Setup] button w [Live] button e Multi-screen buttons r Image type buttons t Image capture size buttons...
  • Page 6 y AUX buttons (*2) These buttons will be displayed only when "Terminal alarm 3" is selected for "AUX output" on the setup menu. ( Setup Instructions) : The letters "OPEN" on the button will turn green and the status of AUX connector will be open.
  • Page 7 Preset map-shot: 8 thumbnail images of the preset position 1-8 ( Setup Instructions) will be displayed orderly on a newly displayed window. When a thumbnail image is clicked, the camera moves to the respective position and live images will be displayed on the "Live"...
  • Page 8 Full screen button Images will be displayed on a full screen. To return to the "Live" page, press the [Esc] key. When dis- playing images on a full screen, the audio transmis- sion button will become unavailable. One shot button Click this button to take a picture (a still picture).

  • Page 9: Monitor Images From Multiple Cameras

    • When MPEG-4 image is being displayed, it may take time to display the frame border indicating an area selected by dragging the mouse. Important: When the camera position is moved inadvertently while the power of the camera is on, restart the cam- era (restart) or refresh the camera position (position refresh) on the [Initialization] tab of the "Maintenance"...

  • Page 10: Record Images On The Sd Memory Card Manually

    Record images on the SD memory card manually Images displayed on the "Live" page can be recorded on the SD memory card manually. This button is operable only when "Manual" is selected for "Save trigger" on the setup menu. ( Setup Instructions) Images recorded on the SD memory card can be copied onto the PC.

  • Page 11: Action At An Alarm Occurrence

    Notify of alarm occurrences to the designated IP addresses (Panasonic alarm protocol) This function is available only when a Panasonic device, such as the network disk recorder, is connected to the sys- tem. When "ON" is selected for "Panasonic alarm protocol", the connected Panasonic device will be notified that the camera is in the alarm state.

  • Page 12: Transmit Images Onto An Ftp Server

    Transmit images onto an FTP server Images can be transmitted to an FTP server. By configuring the following settings, transmission of images captured at an alarm occurrence or captured at a designated interval to an FTP server will become available. Important: •...

  • Page 13: Save Images On The Sd Memory Card When Images Fail To Transmit Using The Ftp Periodic Transmission Function

    Images saved on the SD memory card can be obtained from the [SD memory card] tab of the "Basic setup" page. ( Setup Instructions) To use the SD memory recording function featured in Panasonic’s network disk recorder, select "OFF" for "FTP peri- odic transmission" ( Setup Instructions) and "FTP error" for "Save trigger" ( Setup Instructions).

  • Page 14: Display The Log List

    Display the log list The following logs can be displayed in list form. • Alarm log: Logs of the alarm occurrences such as time and date of the alarm occurrences and the alarm type will be displayed. • Manual log: Logs filed when images have been recorded on the SD memory card will be displayed.
  • Page 15 Log list displayed in the log list win- [Number of the listed logs] Total number of the logs of the selected log type and a number of the log being displayed on the top of the log list will be displayed. Note: Enter the desired log number and press the [Enter] key on the keyboard.
  • Page 16 [Download] button Click this button to download all logs of the selected log list as a file onto the PC. [CLOSE] button Click this button to close the log list window.

  • Page 17: Playback Of Images Saved On The Sd Memory Card

    Playback of images saved on the SD memory card When clicking a time and date listed on the log list window, the "live" page will turn to the "playback" page. When images associated with the clicked time and date are on the SD memory card, the first image of them will be displayed.
  • Page 18 [STOP] button Playback will stop and the "playback" window will turn to the "live" page. [NEXT IMAGE] button The next frame will be displayed and paused when this button is clicked during playback. Each time this button is clicked during pausing, the frame next to the currently displayed frame will be dis- played.

  • Page 19: About The Network Security Of The Camera

    About the network security of the camera Equipped security functions The following security functions are featured in this camera. q Access restrictions by the host authentication and the user authentication It is possible to restrict users from accessing the camera by setting the host authentication and/or the user authentication to "ON".

  • Page 20: Viewing Help

    Viewing Help If you want to know anything about operation or setup methods on screen, display the "Help" screen. Displaying the Help screen Setup screen Help screen Step 1 Click the [Setup] button. → The setup screen is displayed. Clicking an underlined item win display the "Help" pop-window.
  • Page 21 Unit Company of Panasonic Corporation of North America Security Systems www.panasonic.com/security For customer support, call 1.877.733.3689 Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094 Zone Office Eastern: Three Panasonic Way, Secaucus, New Jersey 07094 Central: 1707 N. Randal Road, Elgin, IL 60123 Southern: 1225 Northbrook Parkway, Suwanee, GA 30024 Western: 6550 Katella Ave., Cypress, CA 90630...

This manual is also suitable for:

Wv-nw964

Table of Contents