Page 1 FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 Telephone: (313) 594-4857 Fax: (313) 390-0804...
Page 3: Table Of Contents
Table of Contents Introduction ....1 Instrumentation ....7 Electronic Sound Systems .
Page 5: Introduction
(Refer to Gearshift in the Index) Ford’s Commitment to You At Ford Motor Company, excellence is the continuous commitment to achieve the best result possible. It is dedication to learning what you want, determination to develop the right concept, and execution of that concept with care, precision, and attention to detail.
Page 6 Continuous improvement is essential to our success. We must strive for excellence in everything we do: in our products — in their safety and value — and in our services, our human relations, our competitiveness, and our profitability. Employee involvement is our way of life. We are a team. We must treat one another with trust and respect.
Page 7: Maintenance Schedule
Index so that you can find information under a technical term. Canadian Owners — French Version French Owner Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3.
Page 8 If you lose your Warranty Guide, you can get a new one free of charge. Contact any Ford or Lincoln-Mercury dealer, or refer to the addresses and phone numbers on the first page of this Owner’s Guide. Ford’s Extended Service Plan (ESP)
Page 9 Change your speed often as you drive. Do not drive at one speed for a long time. Use only the type of engine oil that Ford recommends. See Engine oil in the Index. Do not use special “break-in” oils. Avoid sudden stops. Because your vehicle has new brake linings, you should take these steps: —...
Page 10 This guide describes equipment and gives specifications for equipment that was in effect when this guide was approved for printing. Ford may discontinue models or change specifications or design without any notice and without incurring obligation.
Page 11: Instrumentation
Instrumentation Warning Lights and Gauges The instrument panel (dashboard) on your vehicle is divided into several different sections. The illustrations on the following pages show the major parts of the instrument panel described in this chapter. Some items shown may not be on all vehicles. In your vehicle, the warning lights and gauges are grouped together on the instrument panel.
Page 13 Instrumentation Indicator Lights and Chimes Brake System Warning Light The warning light for the brakes can show two things — that the parking brake is not fully released, or that the brake fluid level is low in the master cylinder reservoir. If the fluid level is low, the brake system should be checked by your dealer or a qualified service technician.
Page 14 Anti-Lock Brake System Warning Light (If Equipped) To check the anti-lock brake warning light, turn the ignition key to the ON position. The ABS warning light should glow momentarily. NOTE: If it does not glow at all or stays on for a long time, have your vehicle’s electrical system checked immediately.
Page 15 Instrumentation Safety Belt Warning Light and Chime This warning light and chime remind you to fasten your safety belt. If the safety belt is not buckled when the ignition is turned to the ON position, the chime will sound for four (4) to eight (8) seconds and the light will remain on until the safety belt is fastened.
Page 16 WARNING If any of these things happen, even intermittently, have the air bag system serviced at your Ford or Lincoln-Mercury dealer immediately. Supplemental air bag readiness light Service Engine Soon Warning Light Your vehicle is equipped with a computer that monitors the engine’s emission control system.
Page 17 Instrumentation Service Engine Soon warning light What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate.
Page 18 WARNING Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Charging System Light This light indicates that your battery is not being charged and that you need to have the electrical system checked.
Page 19 Instrumentation Oil pressure light The light should turn off after a few seconds. If the light stays on or illuminates when the engine is running, your vehicle has lost oil pressure and continued operation will cause severe engine damage. If your vehicle loses engine oil pressure: 1.
Page 20 Cruise Indicator Light The CRUISE indicator light will illuminate when the speed control system is activated. Cruise indicator light Overdrive Off Indicator Light This light illuminates when the OVERDRIVE OFF/ON button on the gearshift selector lever has been pushed. When the light is on, the transmission does not shift into overdrive.
Page 21 Instrumentation Low Fuel Light The low fuel light illuminates when the fuel sensor indicates approximately 1/8 of a tank. It will remain illuminated until the tank is filled with enough fuel to pass the 1/8 full level. Low fuel light Low Washer Fluid Light The low washer fluid light will remain illuminated when the washer fluid sensor indicates that the washer fluid level is low.
Page 22 ‘‘Headlamps On’’ Alert Chime This chime will sound if you open the door while the headlamps or parking lamps are on. Gauges Fuel Gauge The fuel gauge displays approximately how much fuel you have in the fuel tank. The fuel gauge indicator may vary slightly while the vehicle is in motion.
Page 23 Instrumentation Under any circumstances, if the pointer moves past the upper limit of the NORMAL band, the engine is overheating and engine damage may occur. If your engine overheats: 1. Pull off the road as soon as it is safely possible. 2.
Page 24 Odometer The odometer records the total distance the vehicle has been driven. Trip Odometer The trip odometer records the distance of individual trips. Before each trip, set the trip odometer to zero by pushing the reset control. Speedometer, odometer and trip odometer...
Page 25 Instrumentation Tachometer The tachometer tells you how fast the engine is running by indicating approximate engine revolutions per minute. Driving with the pointer in the red zone may cause engine damage.
Page 27 Instrumentation The electronic cluster has all of the same warning lights as the mechanical cluster, however, some of the gauges will be electronic instead of analog. In addition, the electronic cluster has a fuel computer which displays fuel economy, distance to empty and outside air temperature.
Page 28 Fuel Gauge Engine coolant temperature gauge The fuel gauge displays approximately how much fuel you have in the fuel tank. The number of bars illuminated in the display indicates how much fuel is left. An accurate reading may be obtained when the vehicle is on smooth, level ground. Fuel gauge...
Page 29 Instrumentation Fuel and Distance Computer Fuel and distance computer switches The fuel and distance computer has five buttons to operate the different functions. SELECT — The SELECT button lets you choose the functions of the fuel computer. Each time you press the SELECT button, the computer advances to the next choice on the menu.
Page 30 OD/TRIP — The OD/TRIP button lets you switch the display between the permanent odometer mileage and the trip odometer mileage. Fuel computer functions Fuel and distance computer display OUTSIDE TEMP This feature lets you display the temperature of the air outside of your vehicle.
Page 31 Instrumentation INST ECONOMY Your instantaneous fuel economy is the fuel economy you get at any particular moment. For example, you can see what your fuel economy is in heavy traffic or on the highway. Factors such as braking, acceleration, and road terrain affect your fuel economy.
Page 32 To display the average fuel economy: 1. Press the SELECT button until the menu displays AVG ECONOMY. 2. You will probably display the average fuel economy for each tank of fuel or for each trip you take. Each time you want to recalculate the average fuel economy, you need to press the RESET button.
Page 33: Electronic Sound Systems
Electronic Sound Systems Audio Systems Your vehicle has one of three audio systems depending upon which options you selected.
Page 37 Electronic Sound Systems Radio Controls How to turn the radio on and off Press the “VOL-PUSH ON” knob or the “AM/FM” button to turn on the radio. Press the “VOL-PUSH ON” knob again to turn it off. How to adjust the volume Turn the “VOL-PUSH ON”...
Page 38 You can change the frequency up or down one increment at a time (FM changes in increments of 200 kHz; AM changes in increments of 10 kHz) by pressing the “TUNE” button. To change frequencies quickly, press and hold down either the right or left side of the “TUNE”...
Page 39 Electronic Sound Systems Setting the station memory preset buttons Your radio is equipped with 6 station memory buttons. These buttons can be used to select up to 6 preset AM stations and 12 FM stations (6 in FM1 and 6 in FM2). Follow the easy steps below to set these buttons to the desired frequencies: 1.
Page 40 NOTE: If there are fewer than six strong stations in the frequency band, the remaining unfilled buttons will store the last strong station detected on the band. After all stations have been filled, the radio will begin playing the station stored on memory button 1. To deactivate the Auto Memory Store mode and return to the manually-set memory button stations, simply push the “AUTO SET”...
Page 41 Electronic Sound Systems NOTE: Illuminated bars in the display show relative levels of bass and treble, and positions of speaker balance and fader functions (left to right, front to rear). Cassette Tape Player Operation How to insert a tape Your cassette tape player is equipped with power loading. Once you insert a tape and push slightly (with the open edge to the right), the loading mechanism draws the tape the rest of the way in and play will begin after a momentary tape tightening...
Page 42 3. Using the “SEEK” function with a cassette tape While in the tape mode, push the right ( ) side of the “SEEK” button to seek forward to the next selection on the tape. Push the left ( ) side of the “SEEK” button to seek the previous tape selection.
Page 43 Electronic Sound Systems How to stop the tape Press the “AM/FM” button to stop the tape player and resume radio play. Similarly, press the “CD” button to stop the tape player and resume CD play. Also, pressing the “TAPE” button while the tape is playing pauses tape play.
Page 44 Using a Ford Cassette Cleaning Cartridge or equivalent to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 45 Electronic Sound Systems Ford CD Changer (If equipped) Ford CD Changer The Ford Compact Disc Changer operates when the Premium Sound or Supersound Audio System is on and a magazine with disc(s) is inserted. Handle the discs by their edges only. Be...
Page 46 NOTE: In some instances, the radio may have CD changer controls, even if there is no CD changer. The digital display on the radio shows the disc and track number. Indicators for compression on (“COMP”) and shuffle on (“SHUFFLE”) are also in the display. These features are described in more detail later in this chapter.
Page 47 Electronic Sound Systems How to locate a selection on your CD Changer using Automatic Music Search Automatic Music Search allows you to quickly find a particular selection on the selected disc. Press the left ( ) side of the “SEEK” button to locate a previous track or the right ( ) side of the “SEEK”...
Page 48 Special Features of Your CD Changer Compression The compression feature will bring soft and loud passages closer together for a more consistent listening level. To turn the compression on, press the “COMP” button. When on, the compression indicator (“C”) will appear in the display. Press the button again to turn off.
Page 49 Electronic Sound Systems How to Take Care of and Clean Your CD Changer and Discs To ensure the continued performance of your Ford Compact Disc Changer, carefully read the following precautions: Always handle the disc by its edge. Never touch the playing surface.
Page 50 CD format. Because of this, a new disc that is free of dust and scratches could be defective and may not play on your Ford Compact Disc Changer. If play does not begin after the CD button is pushed: Moisture may have condensed on the lenses within the unit.
Page 51 Electronic Sound Systems Rear Seat Radio Control Operation Rear seat radio controls (if equipped) How to turn the rear seat radio controls on and off Press memory preset buttons “3” and “5” simultaneously on the face of your radio to turn the rear seat radio controls on. A headphones symbol ( ) will appear in the display when the rear seat controls are on.
Page 52 Using the “PROGRAM ADVANCE” button This button has different functions depending on the audio source. In radio mode, pressing this button will cycle through the memory presets for the given frequency band (AM, FM1, FM2). In the cassette mode, pressing this button will change tape sides.
Page 53 Electronic Sound Systems How to Use Your Steering Wheel Audio Controls (If equipped) If your vehicle is equipped with steering wheel audio controls, the controls are located on the inner right rim of the steering wheel. These controls duplicate some of the audio functions. How to adjust volume Press the up arrow button ( ) to increase the volume.
Page 54 If there is a building or large structure between the antenna and station, some of the signal “bends” around the building, but certain spots receive almost no signal. Moving out of the “shadow” of the structure will allow the station to return to normal. This condition exists when the radio waves are reflected off objects or structures;...
Page 55 (36,000 miles) whichever comes first. Consult your vehicle warranty booklet for further information. Servicing Your Audio System At Ford Audio, we stand behind our audio systems with a comprehensive service and repair program. If anything should go wrong with your Ford Audio System, return to your dealer for service.
Page 56 Notes...
Page 57: Controls And Features
Controls and Features Your vehicle has a variety of features designed for your comfort, convenience and safety. Read this chapter to find out about standard and optional features.
Page 59 Controls and Features The instrument panel (dashboard) on your vehicle is divided into several different sections. Illustrations are provided for the major parts of the instrument panel that are explained in this chapter. Some items shown may not be on all vehicles.
Page 60: Climate Control Systems
The controls for the climate control systems, headlamps, clock, radio, rear window washer and wiper, hazard flasher, power mirror controls, and speed control are all on the instrument panel. Climate Control Systems Climate control system panel Function Selector Buttons There are six function selector buttons: OFF, Mix, Defrost, Panel, Panel/Floor, and Floor.
Page 61 Controls and Features WARNING Operating with the function selector control in off or in the recirculated air mode for extended periods of time in cold weather can result in fog buildup on interior glass surfaces. The Mix ( ) button directs approximately equal amounts of air to the windshield and floor outlets with a small amount to the side windows.
Page 62 There are several air outlets on the instrument panel. There are side outlets near the driver’s window and passenger’s window, two center outlets, floor outlets, and windshield outlets. The direction and amount of air flow from the center and side instrument panel outlets can be adjusted for personal comfort.
Page 63 Controls and Features Turning on the heat Heat will be available when the engine has been running for a sufficient time as indicated by the engine coolant temperature gauge. To heat the inside of your vehicle: 1. Press the function selector button for Floor. Heating only climate control system panel 2.
Page 64 To defrost the windshield and side windows: Press the Defrost button, turn the temperature control knob to the WARM (red) area and turn the fan speed knob to the position of your choice. The recirculated air feature will be automatically turned off in this setting (outside air will be provided).
Page 65 Controls and Features Do not place objects under the front seats unless your vehicle is equipped with an underseat storage compartment. Improperly stored objects will interfere with the flow of air to the back seats. Remove any snow, ice, or leaves from the area below the windshield on the outside of your vehicle.
Page 66 Heating and air conditioning climate control system panel The standard heating system and the heating portion of the heating and air conditioning system are essentially identical. There is one exception, however; the air conditioning compressor may automatically engage when the Defrost position is selected to aid in defogging and defrosting the inside glass.
Page 67 Controls and Features Turning on the air conditioner To cool your vehicle quickly in warm weather: 1. Press one of the function selector buttons (typically Panel, but Panel/Floor, Floor or Mix can be selected). 2. Turn the temperature control knob to COOL. 3.
Page 68 NOTE: The A/C button independently toggles the A/C system’s compressor signal and indicator light ON and OFF in the Panel, Panel/Floor, Floor, Defrost and Mix functions. The A/C button will not operate or light when the system is set in the OFF position. The A/C button will operate in defrost but will not override previously discussed automatic operation.
Page 69 Controls and Features Ventilating your vehicle with outside air In mild weather, you can ventilate your vehicle with outside air. If the outside temperature is less than 70° F (21° C), you can add cool air to your vehicle without using air conditioning. You will get better fuel economy this way.
Page 70 NOTE: The compressor will not operate when the outside temperature is less than about 40° F (4° C). Rear Passenger Compartment Climate Control System for Vehicles with Non-Automatic Temperature Control Systems (If equipped) If your vehicle is equipped with rear passenger compartment climate controls, the rear seat occupants can select their own personal climate comfort level.
Page 71 Controls and Features Rear seat climate control system panel NOTE: For maximum heating and cooling for front seat passengers, set the rear fan switch to the OFF position. Automatic Temperature Control System The control for your Automatic Temperature Control (ATC) is located at the center of the instrument panel above the radio.
Page 72 The ATC maintains the temperature you select and automatically controls the airflow for your comfort. It also allows you to override the automatic operation of airflow and fan speed with manual function selector buttons and the fan speed dial. When you select the AUTOMATIC button, the system determines airflow location and fan speed automatically.
Page 73 Controls and Features if you choose to manually override the airflow location by selecting one of the function selector buttons, you will also need to select the A/C button if you desire cool air-conditioned air. (Your ATC automatically operates the air conditioning [if required] when you are in the AUTOMATIC mode without illuminating the A/C button, but the system requires you to manually select the A/C button if you desire A/C operation when you manually...
Page 74 When in AUTOMATIC and weather conditions require heat, air is sent to the floor. However, a feature is included in the ATC to prevent blowing cold air to the floor if the engine coolant is not warm enough to provide heating. Within three or four minutes (once the engine coolant is warm enough), the fan speed gradually increases and airflow changes to the floor.
Page 75 Controls and Features Changing the Display Mode (English/Metric) To switch between the English and Metric display mode, press the DEFROST and A/C buttons simultaneously while rotating the fan speed dial upward until it stops moving. After one second, the display will begin to toggle between English and Metric. Fan Speed and Thumbwheel The ATC automatically adjusts the fan speed to the existing conditions.
Page 76 Press this button to obtain maximum airflow to the windshield. Adjust the temperature setting as required for defrosting. The indicator light illuminates and the display window shows the set temperature. When the outside temperature is about 50° F (10° C) the air conditioning functions in order to dehumidify the air to prevent window fogging.
Page 77 Controls and Features Air Conditioning and Air Recirculation Activate the air conditioning in any of the function selector override modes by pressing the A/C button. The A/C indicator light on the button illuminates to verify activation, and cooled air flows from the vents. Fan speed continues to be controlled by the ATC unless the fan speed dial is used to override the ATC.
Page 78 If the rear seat climate control lever is set in any of the fan speed positions (1-4), air will be discharged from the rear seat vents at the corresponding speed. Rear seat passengers can choose airflow to be distributed out of the upper or lower vents by using the vent selection switch on the rear climate control panel.
Page 79 Controls and Features Liftgate Window Features Rear Window Defogger (If equipped) The defogger for the rear liftgate window clears frost, fog, or thin ice from both the inside and outside of the rear window. The defogger operates with the ignition in the ON position. If your vehicle is equipped with heated rearview mirrors, they activate when the rear window defogger is switched on.
Page 80 The defroster will turn off when the ignition key is turned to the OFF or START position. Never use sharp instruments or abrasive window cleaners to clean the inside of your rear window. If you do, you may damage the wires that are bonded to the inside of the rear window, and cause damage to the rear window defogger.
Page 81: Hazard Flasher Switch
Controls and Features To activate the rear washer, press the RR WASH switch. For a constant spray, hold the switch for a few seconds. For less washer fluid, press the switch once and release it. When you activate the washer, the wiper will cycle twice and then stop. Do not activate the washer for longer than 15 seconds continuously.
Page 82 The headlamp knob A chime will sound if any of the exterior lamps are on when the driver door is opened. Daytime Running Light (DRL) System (Canadian vehicles only) The Daytime Running Light (DRL) system turns the high beam headlamps on, with a reduced light output, when: the engine is running the vehicle has a fully released parking brake the headlamp system is in the OFF or first (parking lamps)
Page 83 Controls and Features WARNING The Daytime Running Light (DRL) system will not illuminate the tail lamps and parking lamps. Turn on your headlamps at dusk. Failure to do so may result in a collision. Lighting Up the Instrument Panel The instrument panel lights can be turned on by turning the headlamp control knob to either the first or second position.
Page 84 keep the headlamps on for approximately three minutes after you turn the key to OFF To set the autolamp: 1. Make sure the headlamp control knob is in the OFF position. If the knob for the headlamps is on, the autolamp system is canceled.
Page 85 Controls and Features NOTE: Be sure that you do not put anything on top of the photodiode located in the top right side of the instrument panel speaker grille. The photodiode controls the autolamp; if it is covered, the photodiode reacts as if it is nighttime, and the headlamps will be illuminated.
Page 86 Interior Lamps The front dome lamp is located overhead between the driver and front passenger seats. However, if your vehicle is equipped with a power sunroof, the dome lamp is located behind the driver’s seat. The rear dome lamp is located overhead near the rear seating positions.
Page 87 Controls and Features If the vehicle doors are not fully closed and the interior lamps remain illuminated, they will eventually turn off automatically to prevent the battery from becoming discharged. Lamps that illuminate when the front doors and the sliding door are open will turn off after approximately 30 minutes.
Page 88 Overhead Map Lamps (If equipped) The power sunroof overhead console also contains the overhead map lamps. The overhead map lamps You can turn the map lamps on and off by pressing the switches next to the lamps. Radio For information about the radio in your vehicle, refer to the Electronic Sound Systems chapter.
Page 89: Coin Tray
Controls and Features Coin Tray The slide-out coin tray is located in the instrument panel for your convenience. It is located below the radio controls. Coin tray...
Page 90 Ignition Understanding the Positions of the Ignition Your vehicle’s ignition has four positions. They are: The ignition positions OFF/LOCK allows you to shut off the engine and all accessories and locks the gearshift lever. Removing the key then locks the steering wheel. ACCESSORY allows you to operate some of your vehicle’s electrical accessories while the engine is not running.
Page 91: Turn Signal Lever
Controls and Features Turn Signal Lever You can use the turn signal lever on the left side of the steering column to: operate the turn signals. turn the headlamps to high beam. flash the headlamps. turn the windshield wipers and washer on/off. Turn Signals Move the lever up to signal a right turn.
Page 92 Cornering Lights Your vehicle is equipped with special cornering lights designed to provide additional illumination toward the direction you are turning. The corresponding light comes on when a turn is signaled. The headlamp control must be on in order to activate the cornering lights.
Page 93: Windshield Wipers And Washer
Controls and Features Windshield Wipers and Washer Variable Interval Wipers Your vehicle has wipers that you can set to operate at varying intervals. For example, you can set the interval so they wipe less often in light rain or more often in heavier rain. Variable interval wiper control To set the interval wipers, rotate the knob at the end of the turn signal lever to the most effective interval.
Page 94: Gearshift Lever
WARNING Always warm up the windshield with the defroster before you use the washer fluid. In freezing weather, the washer solution may freeze on the windshield and obscure your vision. For information about refilling the washer fluid or replacing your windshield wiper blades, see Windshield washer fluid and Wipers in the Index.
Page 95: Tilt Steering
Controls and Features Tilt Steering WARNING Never adjust the steering wheel when the vehicle is moving. Tilt release lever location To change the position of the steering column, pull the release lever on the column down. Move the steering wheel to the desired position and raise the lever to lock the steering wheel in place.
Page 96 Speed Control (If equipped) The speed control system allows your vehicle to maintain a set speed above 30 mph (48 km/h) without keeping your foot on the accelerator pedal. Avoid using the speed control when driving under the following conditions: it is not possible to keep the vehicle at a set speed in heavy traffic or in traffic that varies in speed on winding or hilly roads...
Page 97 Controls and Features Setting the Speed Control To set the speed control, accelerate your vehicle to the desired speed (at least 30 mph [48 km/h]), push and release the COAST/SET button on the left side of the steering wheel. The CRUISE light in the instrument cluster will come on.
Page 98 Accelerating With the Speed Control Operating To pass another vehicle while the speed control is activated, press the accelerator pedal. When you release the pedal, the vehicle will return to the previously set speed. Driving Uphill or on a Steep Grade The vehicle may not maintain the set speed when going up or down steep hills.
Page 99 Controls and Features Resetting the Speed Control To reset at a higher speed, use one of the following methods: Press the accelerator pedal. When the speedometer indicates the desired speed, push and release the COAST/SET button. Push and hold the RES/ACCEL button. When the vehicle attains the speed you desire, release the switch.
Page 100 When the CRUISE indicator blinks, press the speed control OFF switch and have the system checked by your Ford or Lincoln-Mercury dealer. The CRUISE indicator light may blink if the CRUISE CONT. ON switch is pressed while pushing the RES/ACCEL, COAST/SET, or CANCEL buttons located on the left side of the steering wheel.
Page 101 Controls and Features Sliding Shade The sunroof has a sliding shade you can manually open or close to block the sun when the glass panel is shut. To close the sliding shade, pull the shade toward the front of the vehicle. The shade automatically opens when the sunroof is opened.
Page 102 Automatic Door Lock If your vehicle is equipped with the optional power door locks, locking the driver door with the key or with the manual rocker switch will also lock all other doors. However, when the driver door is unlocked, with the key or with the manual rocker switch, other doors remain locked.
Page 103 Controls and Features The sliding door exterior lock To release the catch and close the door, pull the handle toward the front of the vehicle. Be sure it is fully closed. The sliding door interior lock...
Page 104 Childproof Lock for the Sliding Door Your vehicle has a childproof lock for the sliding door. If you set the childproof lock, the sliding door cannot be opened from inside the vehicle. Childproof lock location...
Page 105 Controls and Features The childproof lock: prevents children inside the vehicle from opening the door. allows the door to be opened from the outside (if the door is unlocked). To set the childproof lock: 1. Open the sliding door. 2. Find the childproof lock knob above the label. 3.
Page 106 The power door lock switch NOTE: If the sliding door is open when all doors are locked with the power door lock switch, the sliding door automatically locks when it is closed. You can manually lock and unlock the doors using the manual door locks to override the power locks.
Page 107 Controls and Features Opening the liftgate Opening the Liftgate Window (If equipped) To open the liftgate window only, turn the key clockwise. The window unlatches and the rear wiper falls out of the way. Do not force the wiper down by hand — it moves when the key is turned.
Page 108: Closing The Liftgate
The liftgate window in the open position WARNING Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.
Page 109 Controls and Features The liftgate has an intermediate and a fully closed position. Push on the liftgate to make sure it is fully closed before you drive your vehicle. Locking the liftgate using the lock lever...
Page 110 You can lock the liftgate by pushing in the lock lever before you begin to close the liftgate. You can also lock the liftgate by closing the liftgate, inserting your key and turning it clockwise until you hear the lock lever engage. If you turn it too far, the optional liftgate window will open.
Page 111 Controls and Features Driver’s side power window controls One-Touch-Down Power Window (Included with optional power windows -- driver side only) The one-touch-down power window feature allows you to completely open the driver’s window without holding down the window switch. To open the window completely, press the switch down for about one second, then release it.
Page 112 Manual flip-open quarter window latch location NOTE: Optional third-row power windows must be opened with the overhead console controls. Power Quarter Windows (If equipped) The power quarter windows operate with the ignition in the ON position. The power-operated quarter windows in the third seat position are controlled by the RIGHT VENT and LEFT VENT switches on the overhead console.
Page 113 Controls and Features Power quarter window switch Mirrors WARNING Make sure you can see clearly through the rearview mirror at all times. Do not block your vision. If you cannot see through the mirror, it could result in a collision, injuring yourself and others.
Page 114 Dual Electric Remote Controlled Mirrors (If equipped) If you have power side view mirrors, you can adjust them in any direction by using the mirror controls on the instrument panel. This switch operates with the ignition in ON or ACC. The mirror control switch is on the instrument panel to the left of the steering wheel.
Page 115 Controls and Features Dual electric remote controlled mirrors switch Heated mirror feature (If equipped) Both power mirrors are heated whenever the rear window defroster is turned on. Do not remove ice from the mirrors with a scraper or you could damage them. Cargo Net (If equipped) The cargo net is designed to hold your cargo upright between the third row bench seat and the liftgate to prevent it from moving...
Page 116 WARNING Be sure to secure all four loops into the retainers. The cargo restrained in the net must not exceed 50 lbs. (22.5 kg) or the net may not stay secured. To remove the cargo net, remove the loops from the four retainers.
Page 117 Controls and Features Remote Keyless Entry System (If equipped) If you have chosen the remote keyless entry system option for your vehicle, you can lock or unlock the doors and liftgate without using a key. This option will allow you to open your vehicle using a remote transmitter from distances of up to 49 feet (15 meters) away.
Page 118 Replacement batteries can be purchased at most pharmacies, watch stores or at your Ford or Lincoln-Mercury dealer. NOTE: The operating range of the remote entry system can also be affected by weather conditions (such as very...
Page 119 Controls and Features Remove the two batteries by snapping open the lid of the remote transmitter. The transmitter can be snapped apart by twisting a thin coin between the two halves of the transmitter. Replace the batteries with new ones as shown in the above illustration. Close the lid securely.
Page 120 ID Code Programming Procedure NOTE: All transmitters must be programmed (or reprogrammed) at the same time. If the programming mode is entered and the transmitters are not programmed (or reprogrammed) at the same time, they will not operate with the system. 1.
Page 121 Controls and Features To arm the system 1. Remove the key from the ignition. 2. Lock the doors by using either the power door lock switch or by turning the key in either the driver or passenger door lock cylinder. The parking lights will flash and the horn chirps to let you know that the system has been armed.
Page 122 NOTE: Be sure to close all the doors completely. If the doors are not completely closed, the alarm indicator light will remain on steadily. The anti-theft system is armed only when the anti-theft indicator light remains on steadily for approximately 30 seconds after the last door is closed, and then flashes every 2.5 seconds.
Page 123 Controls and Features Disarming a triggered anti-theft system The alarm can be disarmed by: unlocking the driver or passenger doors unlocking the doors with the remote keyless entry transmitter (if equipped) putting the key in the ignition and turning it to the ACC position NOTE: The flashing lights and honking horn will shut off automatically within 2 minutes 30 seconds after the...
Page 124 Notes...
Page 125: Seating And Safety Restraints
Seating and Safety Restraints Seats Head Restraints If you use them properly, head restraints will help protect your head and neck in a collision. The head restraints can be adjusted in four positions: fully raised, fully lowered and two intermediate positions. Press down on the head restraint adjustment button and move the restraint to the position that places the restraint directly behind your head.
Page 126 Adjusting the Front Seats Manually If you have manually adjustable front seats, you can move your seat to a new position by lifting up on the seat adjustment lever and sliding the seat to the position of your choice. The lever is underneath the front of your seat.
Page 127 Seating and Safety Restraints Reclining Seats You can tilt back the seats in your vehicle. WARNING Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To recline the seatbacks: 1. Lift up the release lever and hold it up while you lean against the back of the seat.
Page 128 Using Power Seats (If equipped) If your vehicle has power front seats, you can adjust the driver seat in six directions: forward (using the power slide switch) rearward (using the power slide switch) raise the seat (using the power seat height switch) lower the seat (using the power seat height switch) tilt seat back towards the front (using the power recline switch)
Page 129 Seating and Safety Restraints Six-way power seat controls location Six-way power seat controls...
Page 130: Storage Compartments
Storage Compartments Underseat Storage Compartment (If equipped) The underseat storage compartment is located underneath the front passenger seat. It can be opened by pulling it toward the instrument panel. The underseat storage compartment...
Page 131 Seating and Safety Restraints Front Seat Cupholders The front seat cupholders are located on the side of the passenger’s seat. Find the indented ledge and pull it down, away from the side of the seat, toward the driver seat. When the cupholder is not in use, push the cupholders into the cover and lift the cover into its fully stored position.
Page 132 Rear Seat Cupholders (available on some models) Your vehicle may have the following types of cupholders: two second row cupholders attached to the captain seats (if equipped) two third row cupholders on the left side and one cupholder on the right side (if equipped) one cupholder built into the side trim panel (without rear radio controls) WARNING...
Page 133 Seating and Safety Restraints Important Safety Belt Information The use of safety belts helps to restrain you and your passengers in case of a collision. In most states and in Canada, the law requires their use. Safety belts provide best restraint when: the seatback is upright the occupant is sitting upright (not slouched) the lap belt is snug and low on the hips...
Page 134 WARNING Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm.
Page 135: Combination Lap And Shoulder Belts
Seating and Safety Restraints Combination Lap and Shoulder Belts While your vehicle is in motion, the combination lap and shoulder belt adjusts to your movement. However, if you brake hard, turn hard, or if your vehicle receives an impact of 5 mph (8 km/h) or more, the lap and shoulder belt locks and helps to reduce your forward movement.
Page 136 Unfastening the combination lap and shoulder belts — front and rear outboard seating positions Third-row passengers should be aware that the proper safety belt for their seating position is slightly behind their seat. They should not use the second-row safety belts which are in front of the third seat.
Page 137 Seating and Safety Restraints Fastening the rear seat combination lap and shoulder belt To tighten the lap portion of the belt, pull up on the shoulder belt until it fits you snugly. The belt should rest as low on your hips as possible.
Page 138 Using the seat belt guide with the three-passenger bench seat in the second row position...
Page 139 Seating and Safety Restraints NOTE: The second row two-passenger bench seat has a unique safety restraint system. If your vehicle has the two-passenger bench seat it is very important that the unique safety belt system is used properly. Please read Auxiliary safety restraint system for the second row bench seat in this section, which explains the unique safety belt system.
Page 140 Automatic locking mode In this operating mode, the shoulder belt retractor will be automatically locked and will remain locked when the combination lap/shoulder safety belt is buckled, and does not allow the occupant freedom of movement. This mode provides the following: A tight lap/shoulder belt on the occupant.
Page 141 Seating and Safety Restraints NOTE: When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch to the vehicle sensitive (emergency) locking mode. See the detailed instructions under Safety Seats for Children in this chapter. Shoulder Belt Height Adjustment Driver and right front passenger You can adjust the shoulder belt height to one of five (5)
Page 142 WARNING Position the shoulder belt height adjuster so that the belt rests across the middle of your shoulder. Be sure the shoulder belt is properly positioned on your shoulder each time you use the belt. If the shoulder belt is off your shoulder, on your upper arm or neck, there is a greater risk of severe injury in a collision.
Page 143 Seating and Safety Restraints Auxiliary Safety Restraint System for the Second Row Bench Seat (7 passenger vehicle) There is a unique safety restraint system for the outside seating position of the second row bench seat. It is very important that you read and understand this section before anyone rides in the outside seating position (near the sliding door) of the two-passenger bench seat.
Page 144 The auxiliary safety retraint system for the second row bench seat A twisted belt may prevent the retractor from working properly. If the unique safety belt system is twisted, disengage the single window tongue from the buckle on the side of the seat, remove the twist and re-install the tongue into the buckle until you hear a snap and feel the latch engage.
Page 145 Seating and Safety Restraints The auxiliary safety restraint system fastened NOTE: If the three-passenger bench seat is moved up to the second-row position, the outside passenger (near the sliding door) only needs to use the double window tongue and the standard buckle. Because the third-row seat is wider and is closer to the sliding door, the single window tongue and the auxiliary buckle are not necessary.
Page 146 Unfastening the auxiliary safety restraint system Both tongues must be attached to their appropriate buckles whenever someone is riding in that seating position, and when a child safety seat has been installed. When the two-passenger bench seat is removed from the vehicle, you must detach the single window tongue from the auxiliary buckle.
Page 147 Seating and Safety Restraints Exiting a vehicle with the auxiliary safety restraint system Safety Belt Extension Assembly A safety belt may be too short even when it is fully extended. You can add about eight inches (20 cm) to the belt length with a safety belt extension assembly.
Page 148: Safety Belt Maintenance
(slide bar) (if so equipped), child safety seat tether bracket assemblies (if so equipped), and attaching hardware, should be inspected after any collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was...
Page 149 WARNING Do not attempt to service, repair, or modify the air bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. WARNING If you are close to an inflating air bag, it could seriously injure you.
Page 150 Children and Air Bags NOTE: For additional important safety information on the proper use of seat belts, child seats, and infant seats, please read the entire Safety Restraints chapter in this owner guide. WARNING Children should always wear their safety belts. How Does the Air Bag Supplemental Restraint System Work? The Air Bag Supplemental Restraint System is designed to...
Page 151 Seating and Safety Restraints The location of air bags and warning labels WARNING Several air bag system components get hot after inflation. Do not touch them after inflation. WARNING The air bag will inflate only once. The system is designed to function on a one-time-only basis.
Page 152 The Air Bag Supplemental Restraint System consists of: driver and passenger air bag modules (which include the inflators and air bags), one or more impact and safing sensors, a system diagnostic module, a readiness light, and the electrical wiring which connects the components. The diagnostic module monitors its own circuits, the air bag electrical system, the air bag readiness light, the air bag power and the air bag inflators.
Page 153 Seating and Safety Restraints Inflated passenger side air bag Determining If System Is Operational The Air Bag Supplemental Restraint System uses a readiness light to indicate the condition of the system. The readiness light is in the instrument cluster. When you turn the ignition key to ON, this light will illuminate for approximately six (6) seconds and then turn off.
Page 154 If any of these things happen, even intermittently, have the Air Bag Supplemental Restraint System serviced at your Ford or Lincoln-Mercury dealer immediately. Unless serviced, the system may not function properly in the event of a collision. Disposal of Air Bags and Air Bag Equipped Vehicles For disposal of air bags or air bag equipped vehicles, see your local Ford or Lincoln-Mercury dealer.
Page 155: Safety Restraints For Children
Seating and Safety Restraints Safety Restraints for Children In the U.S. and Canada, you are required by law to use safety restraints for children. If small children ride in your vehicle — this generally includes children who are four years old or younger and who weigh 40 pounds (18 kg) or less —...
Page 156 WARNING Whenever possible, put children in one of the rear seats in your vehicle. Accident statistics indicate that children are safer when properly restrained in the rear seats than in the front seats. WARNING Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle.
Page 157 Always follow the safety seat manufacturer’s instructions when installing and using the safety seat. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 158 WARNING Rear-facing child seats or infant carriers should never be placed in the front seats. WARNING If you do not properly secure the safety seat, the child occupying the seat may be injured during a collision or sudden stop. An unsecured safety seat could also injure other passengers.
Page 159 Seating and Safety Restraints WARNING Always keep the buckle release button pointing upward and away from the child seat, with the tongue between the child seat and the release button as shown in the following illustration. WARNING Failure to follow all instructions on the proper use of child seats or the vehicle restraint systems can result in serious injury or death in the event of a sudden stop or collision.
Page 160 Using the Automatic Locking Mode Retractor to Secure a Child Safety Seat Your vehicle is equipped with a dual locking mode retractor on the shoulder belt portion of the combination lap/shoulder safety belt for the front passenger seat and rear outer seats. The automatic locking mode must be used when installing a child seat or infant carrier in the front passenger seat or rear outer seats.
Page 161 Seating and Safety Restraints Routing the safety belt tongue through the child seat (captain’s chair shown) 3. Pull on the belt until all of the stored belt is out of the retractor and a click is heard. 4. Allow the belt to retract. A clicking sound will be heard as the belt retracts.
Page 162 5. Pull up on the shoulder belt to remove slack in the belt while you push down on the child seat. Make sure there is tension in the belt. Removing slack from the safety belt (captain’s chair shown)
Page 163 Seating and Safety Restraints 6. Before placing the child in the child seat or infant carrier, use force to tilt the seat from side to side, and tug it forward to make sure that the seat is securely held in place. Testing the security of the child seat 7.
Page 164 Ford or Lincoln-Mercury dealer. Vehicles built for sale in the USA do not include tether anchor hardware, but it can be obtained at no charge from any Ford or Lincoln-Mercury dealer (Part number F3XY-12613D20-A).
Page 165 Seating and Safety Restraints The chart below specifies, for each seat type and position, where the tether strap must be attached to the vehicle and the section containing the appropriate instructions for tethering.
Page 166 Tethering to floor anchor Ford recommends placing tethered safety seats in a rear seating position with the tether strap attached to the tether anchor bolt as shown in the following illustration. Tether anchor point locations To gain access to the anchoring bolt, cut through the plastic along the U-shaped tether location outlines on the carpet of the luggage area.
Page 167 Seating and Safety Restraints WARNING Only use the tether attachment hole locations shown in the illustrations. The tether anchor may not perform properly if the wrong mounting location is used. WARNING Follow these precautions to decrease the chance of injury in an accident.
Page 168 Tethering to lap/shoulder belt tongue To attach a tether strap to a lap/shoulder belt: 1. Route the tether strap under the headrest and between the head restraint supports. 2. Hook the tether strap hook into the large hole at the end of the tongue of the lap/shoulder belt directly behind the child seat position.
Page 169 Seating and Safety Restraints 5. Let the retractor wind up the slack from the lap/shoulder belt. A clicking sound should be heard as the belt retracts, indicating that the retractor is in automatic locking mode. Tighten the tether strap to remove any slack. 6.
Page 170 Safety Belts for Children Children who are too large for child safety seats should always wear safety belts. (See instructions with your child seat, or contact its manufacturer, to determine maximum size of a child that will fit safely in the safety seat.) WARNING If safety belts are not properly worn and adjusted as described, the risk of serious injury to the child in a...
Page 171 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning...
Page 172 Built-In Child Seats (If equipped) The optional second row bench seat includes two built-in child seats. These child restraints are to be used only by children who: are at least one year old weigh between 10 and 27 kilograms (22 and 60 pounds) whose shoulders are below the shoulder harness slots Children not meeting these requirements should be restrained in an approved aftermarket child safety seat.
Page 173 Seating and Safety Restraints WARNING The second row seatback must be fully locked before operating the child restraint system. Check the position of the seatback release lever. Second row bench built-in child seats...
Page 174 Built-In Child Seat Retractors The retractor will switch from the emergency locking mode to the automatic locking mode when the right shoulder belt is pulled all the way out. The retractor will switch back to emergency locking mode when the belts are unbuckled and the shoulder belts retract completely.
Page 175 Seating and Safety Restraints 1. Hold the tab from the lower outboard side of the child seat and lower the cushion completely.
Page 176 2. If connected, unbuckle the two safety belt tongues. Also detach the chest clip.
Page 177 Seating and Safety Restraints 3. Place the child in the built-in child seat. Position the crotch belt buckle between the child’s legs.
Page 178 4. Place the left shoulder belt harness over the child’s left shoulder. Insert the left shoulder harness tongue into the left side of the belt buckle. Confirm that the left shoulder harness tongue indicator is green. 5. Place the right shoulder belt harness over the child’s right shoulder.
Page 179 Seating and Safety Restraints 8. If the shoulder belts are too tight, unlatch the chest clip and unbuckle the child from the built-in child seat. Allow the shoulder belts to retract fully. Repeat the procedure from step 3 through step 7. Removing the child from the built-in child seat 1.
Page 180 6. Confirm that the built-in child seat is locked in the stowed position by grasping the safety seat cushion and attempting to lower it without pulling the cushion release strap. 7. If the built-in child seat is not locked in the stowed position, repeat steps 4 through 6.
Page 181: Adjustable Rear Seating
Adjustable Rear Seating The removable and adjustable seats are a convenient feature of your vehicle. Reading this chapter will help you learn about the various ways the seats in your vehicle can be arranged to suit your different needs. Your vehicle is a five or seven-passenger vehicle. As a seven-passenger vehicle, it will have either a two-passenger bench seat or two second-row bucket seats and the sliding three-passenger bench seat in the third row.
Page 182: Floor Mats
Floor Mats The removable floor mats Removable Floor Mats Whenever you remove the mats to remove or adjust any of the seats, always remember that the mats must be reinstalled before passengers ride in your vehicle. The floor mats are specifically designed to keep objects out of the seat tracks.
Page 183 Adjustable Rear Seating Review the following illustrations so you will know the proper way to place the floor mats with the various seating arrangements available in your vehicle.
Page 185: Head Restraints
Adjustable Rear Seating NOTE: The step mat should be placed neatly in the cargo area when not in use. Positioning pins are included with your floor mats to secure them to the seat tracks. Push the positioning pins through the plastic loops in the floor mats and into the seat tracks.
Page 186 NOTE: If your vehicle is equipped with the optional two-passenger bench seat with built-in child seats, the head restraints on the two-passenger bench seat are not adjustable. The adjustable head restraint It is not necessary to remove the head restraints from the seats when removing seats from the vehicle.
Page 187 Adjustable Rear Seating WARNING The head restraints should be stored outside of the vehicle (with the removed seat) to prevent them from damaging the vehicle or injuring passengers in the case of sudden braking or a collision. Two-Passenger Bench Seat NOTE: The two-passenger bench seat has a unique safety restraint system.
Page 188 Removing the Two-Passenger Bench Seat 1. Remove the floor mats. Lift the seatback release lever and fold down the back of the seat to the fully folded position. Seatback release lever location 2. Detach the tongue from the auxiliary buckle on the sliding door side of the seat.
Page 189 Adjustable Rear Seating The floor latch levers 4. Place your hand under the seat cushion and tip the front of the seat upward slightly. Slide the seat rearward to release the seat from its anchor position. 5. Two people should lift the seat and remove it from the vehicle. 6.
Page 190 Installing the Two-Passenger Bench Seat To replace the bench seat in its original position: 1. Make sure the area around the floor anchor positions is free from obstruction. 2. With the seatback folded down, two people should lift the seat into the vehicle.
Page 191 Adjustable Rear Seating Captain Seats (If equipped) Quick-Release Captain Seat The quick-release captain seat option allows the captain seat nearest the sliding door to slide forward allowing easier entry and exit to the third-row seats. Pull up on the seat adjustment lever and slide the seat forward.
Page 192 The quick-release bucket seat also has two levers on the back of the seat — one to fold down the seatback and one to slide the seat forward. These levers allow third-row passengers to enter and exit more easily. Quick-release bucket seat levers Removable Captain Seats If your vehicle has second row captain seats, you can remove them if you need extra cargo space.
Page 193 Adjustable Rear Seating Before you remove the seats, remove the floor mats. Then: 1. Pull the seatback release lever up and tilt the back of the seat forward as far as possible. Folding down the seatback...
Page 194 2. Lift up on the two floor latch levers near the front seat legs and release the seat legs from each anchor position. Removing the quick-release bucket seat...
Page 195 Adjustable Rear Seating The removable inside captain seat 3. Place your hand under the seat cushion and tip the front of the seat upward slightly. Slide the seat rearward to release the seat from its anchor position. 4. Two people should lift the seat and remove it from the vehicle. 5.
Page 196 Installing the Removable Captain Seats To position the captain seats back in their original positions: 1. Make sure the area around the floor anchor positions is free from obstruction. 2. With the seatback folded down, two people should lift the seat into the vehicle.
Page 197 Adjustable Rear Seating Three-Passenger Bench Seat When entering and exiting the vehicle, third-row passengers must be careful that they step over the auxiliary safety restraint system that is present with the second-row bench seat. Labels are provided on the back of the second-row bench seat to remind passengers to use care when exiting.
Page 198 Some of the different ways that your vehicle’s seats can be arranged are shown below. NOTE: Do not try to remove the three-passenger sliding seat. Removal of the third seat may negatively affect its ability to slide properly.
Page 199 Adjustable Rear Seating...
Page 200 With the second row seat(s) removed, the three-passenger bench seat can be moved all the way forward, just behind the front seats for more room in the cargo area.
Page 201 Adjustable Rear Seating Moving the Three-Passenger Bench Seat NOTE: When moving the three-passenger bench seat, the seat cushion cannot be lowered unless the seat is in a seating position. If you cannot get the seat cushion to lower, you may have the seat in a storage position. The three-passenger bench seat is not removable, but it can be moved to the second-row position when the second-row captain seats or second-row bench seat has been removed from the...
Page 202 WARNING After moving the third-row seat, be sure to latch the seat in a passenger seating position. Improper location of the seat will prevent correct use of the safety belts and will increase the risk of severe injury in an accident. After sliding the seat, check that both sides of the seat are locked securely by attempting to move each side of the seat forward and backward.
Page 203 Adjustable Rear Seating To move the seat all the way forward: 1. Lift up on the seat cushion release lever and fold up the seat cushion. Seat cushion release lever location...
Page 204 A label describing seat operation can be found underneath the seat cushion on the sliding door side of the vehicle. Seat cushion label location...
Page 205 Adjustable Rear Seating 2. Lift up on the seat position release lever and hold while sliding the seat along the seat tracks in the floor of the vehicle. Sliding the three-passenger seat NOTE: When sliding the seat, be sure the middle belt tongue and buckle are fastened.
Page 206 3. Make sure the seat securely latches in the lock position of both seat tracks before driving with the rear seat in this position. The three-passenger seat in the fully forward locked position...
Page 207 Adjustable Rear Seating 4. Lower the seat cushion only if in a seating position. The seat cushion will not lower in a storage position. Do not try to lower the seat cushion by force because doing so could damage the seat. 5.
Page 208 Fold-Down Table-Top Seats (If equipped) The second and third row seats convert to table tops with built-in cupholders. Lift up on the seatback release lever and fold seatback forward. Seatback release lever location...
Page 209 Adjustable Rear Seating Table and built-in cupholders on the fold-down seatback WARNING You should never place hard items such as coffee mugs or drinking glasses on the table-top seats when the vehicle is moving. Any item can become a projectile inside a vehicle involved in a collision.
Page 210 Notes...
Page 211: Starting
Starting Fuel-Injected Engines When starting a fuel-injected engine, the most important thing to remember is to avoid pressing down on the accelerator before or during starting. Only use the accelerator when you have problems getting your vehicle started. See Starting Your Engine in this chapter for details about when to use the accelerator while you start your vehicle.
Page 212 2. Keep your foot on the brake pedal and turn the ignition key to 3. DO NOT depress the accelerator pedal when starting your engine. DO NOT use the accelerator while the vehicle is parked. 4. Turn the key to the START position (cranking) until the engine starts.
Page 213 Starting NOTE: Your vehicle has an interlock that prevents you from shifting out of P (Park) unless your foot is on the brake pedal. If the engine does not start after two attempts: 1. Turn the ignition key to the OFF position. 2.
Page 214: What To Do If The Engine Does Not Start
WARNING Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. If you consistently start your vehicle in subzero temperatures, use an engine block heater (if your vehicle has this option).
Page 215 Starting Once the shut-off switch is activated, you must reset the switch by hand before you can start your vehicle. The fuel pump shut-off switch reset button is located below the hood release handle. Fuel pump shut-off switch reset button location WARNING If you see or smell fuel, do not reset the switch or try to start your vehicle.
Page 216 5. Check under the vehicle again for leaking fuel. If you see or smell fuel, do not start your vehicle again. If there is no fuel, you can try to start your vehicle again. 6. Check all vehicle warning lights before driving your vehicle. Guarding Against Exhaust Fumes Carbon monoxide, although colorless and odorless, is present in exhaust fumes.
Page 217 Starting Read the section Climate Control Systems for instructions on bringing fresh outside air into your vehicle. Refer to the Index. Removing the Key From the Ignition OFF/LOCK is the only position that allows you to remove the key from the ignition. The LOCK feature helps to protect your vehicle from theft, because it also locks the steering wheel and the gearshift lever when the key is removed.
Page 218 Notes...
Page 219: Driving
Driving Brakes When the foot (service) brake pedal is depressed, the high-mount brake lamp should illuminate. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 220 During ABS activation, a mechanical noise may be heard as the ABS cycles. This is normal ABS operation. Anti-lock brake system (ABS) On vehicles equipped with an anti-lock braking system (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events.
Page 221 Ford Motor Company has not found any negative effects of mobile radio transmitting equipment installed on vehicles with the ABS providing that the radio is installed according to the radio manufacturer’s instructions.
Page 222 Stopping Distances Stopping distances vary with different loads and driving conditions. Use caution when you drive under new conditions and acquaint yourself with your vehicle’s performance. Applying the Brakes Apply the brake pedal evenly. Use the “squeeze” technique. Push on the brake pedal with a steadily increasing force. This allows the wheels to continue to roll while you are slowing down, which lets you steer properly.
Page 223 Driving The parking brake WARNING When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). Turn off the ignition whenever you leave your vehicle. Never leave your vehicle unattended while it is running.
Page 224: Steering Your Vehicle
The parking brake is not designed to stop a moving vehicle, but you can use the parking brake to stop your vehicle in an emergency if the service brakes fail. However, since the parking brake does not stop your vehicle as quickly as the normal brakes, the stopping distance will increase greatly.
Page 225: Automatic Transaxle Operation
Driving Automatic Transaxle Operation Putting Your Vehicle in Gear Your vehicle’s gearshift lever is on the steering column. The OVERDRIVE OFF/ON button is located at the end of the gearshift lever. You can put the gearshift lever in any one of several positions.
Page 226 Shift-lock Safety Feature Your vehicle has a special shift-lock safety feature which prevents you from shifting out of P (Park) without the brake pedal depressed. To shift the transaxle out of the P (Park) position, the ignition must be in the ON position and your foot must be pressing on the brake pedal.
Page 227 Driving Driving When to use D (Overdrive) Overdrive is the normal driving position. When the gearshift lever is placed in (D) Overdrive, and the Overdrive Off button has not been pressed, the vehicle will automatically upshift to second, third and fourth gears. The transaxle will shift into the correct gear when the right speed is reached.
Page 228 The transaxle will be in the “overdrive on” mode when the vehicle is started even if the O/D OFF mode was selected when the vehicle was last shut off. If your vehicle is on an extremely slippery surface, the Electronic Transaxle Control Module may receive a signal indicating a rapid increase or decrease in wheel speed.
Page 229 Driving N (Neutral) In N (Neutral), the transaxle is not locked. Your vehicle will roll freely, even on the slightest incline, unless the parking brake or brakes are on. Parking Always come to a complete stop before you shift into P (Park). This position locks the transaxle and prevents the front wheels from turning.
Page 230: Driving Through Water
Driving Through Water Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall. Water may also enter your engine’s air intake and cause severe damage to your engine.
Page 231: Vehicle Loading Information
Driving Vehicle/Trailer Loads Your vehicle may tow a Class I trailer up to 2,000 lbs. (907 kg) provided the Gross Vehicle Weight (GVW) is less than the GVWR shown on the Safety Compliance Certification Label. With the optional trailer tow package, your vehicle can tow a trailer up to 3,500 lbs.
Page 232 Each additional item of equipment affects how much cargo a vehicle can carry. If a vehicle is overloaded, performance will suffer and service concerns may arise. The following is a typical example of a Safety Compliance Certification Label and an explanation of how this information should be used: The Safety Compliance Certification Label NOTE: The vehicle must not be loaded to both the front and rear...
Page 233 Driving Payload GVW (Gross Vehicle Weight) GVWR (Gross Vehicle Weight Rating) GAWR (Gross Axle Weight Rating) GCWR (Gross Combined Weight Rating) Base Curb Weight The base curb weight is the weight of the vehicle including fuel, coolants, lubricants, emergency tools and spare wheel and tire.
Page 234 Gross Axle Weight Rating (GAWR) Your Safety Compliance Certification Label not only gives the GVWR, it also gives the Gross Axle Weight Rating (GAWR) which is the maximum weight allowed on each axle system. The rating is based on the carrying capacity of the weakest axle and suspension component as well as other factors.
Page 235 Driving Calculating the Payload for Your Vehicle To know how much weight your vehicle can carry: 1. Obtain the GVWR and GAWR from your Safety Compliance Certification Label. Safety Compliance Certification Label location 2. Fill the fuel tank. 3. Weigh your vehicle without cargo. 4.
Page 236 Load Calculation — Trailers The trailer towing table shows the maximum allowable trailer weight and maximum GCWR for vehicles with and without the trailer towing package. For a particular vehicle, the allowable trailer weight may be lower depending upon the vehicle’s actual gross vehicle weight. (GVW is the weight of the vehicle including passengers, equipment, cargo.) You must determine the appropriate trailer weight for your...
Page 237 Driving Trailer towing table If your vehicle exceeds the GVWR, remove cargo from your vehicle accordingly. If your vehicle exceeds either GAWR, shift the load or remove cargo accordingly. To determine actual GCW, weigh the total vehicle and trailer and also weigh the trailer separately to verify its weight.
Page 238 Preparing to Tow For your safety and for the good of your vehicle, use the right equipment for the type of trailer you tow. Also, make sure that all towing equipment is properly installed on your vehicle. If you are not certain that you are using the right equipment in the proper manner, see your dealer or a reliable trailer dealer.
Page 239 Driving Trailer Brakes Separate trailer brakes are required on most trailers weighing over 1,500 lbs. (680 kg). WARNING Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase.
Page 240 If you need further assistance in wiring a trailer to your vehicle, contact your Ford or Lincoln-Mercury dealer. Driving While You Tow Be especially careful when driving while you tow a trailer. Never drive faster than 45 mph (70 km/h) when you tow in hilly country on hot days.
Page 241 Driving Trailer Towing Tips Before starting on a trip, practice turning, stopping and backing in an area away from heavy traffic. Get to know the “feel” of the vehicle/trailer combination. Practice backing up. Back up very slowly, with someone outside at the rear of your trailer to guide you.
Page 242 1. Apply the main brake pedal with your foot and hold it. 2. Have another person place the wheel chocks under the trailer wheels. 3. With the chocks in place, release the brake pedal, making sure the chocks are holding. 4.
Page 243 Driving Four Season Roof Rack (If equipped) Always load your luggage as far back as it will safely go on the four season roof rack. Do not load more than 100 lb. (45 kg). Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear).
Page 244 Notes...
Page 245: Roadside Emergencies
Roadside Emergencies Hazard Flasher Switch The hazard flasher is used to alert other drivers to hazardous situations. The hazard flasher switch operates the same lamps as the turn signal lever. When the hazard flasher is activated, all of these lamps will flash on and off.
Page 246 To use the hazard flasher: 1. Push the HAZARD switch; you will see the turn signal arrows flash. 2. To stop the hazard flashers, push the HAZARD switch again. Hazard flasher switch location Fuel Pump Shut-Off Switch If the engine cranks but does not start or if you have had a collision, the fuel pump shut-off switch may have been triggered.
Page 247 Once you have determined which fuses or circuit breakers to check, follow the procedures under Checking and replacing fuses or Checking and replacing circuit breakers later in this chapter. NOTE: Fuse links should only be repaired by your Ford or Lincoln-Mercury dealer.
Page 248 Checking and Replacing Fuses If you need to check a fuse, find the fuse panel for the electrical system, which is located under the instrument panel, and follow these steps: 1. To remove the fuse panel cover, pull down on the fuse panel cover handle.
Page 249 Roadside Emergencies 2. On the fuse panel cover, find the number of the fuse you want to check. The diagram on the cover tells you where to locate the fuse on the panel. The fuse panel cover...
Page 251 Roadside Emergencies...
Page 252 3. Check the fuse to see if it is blown. Look through the clear side of the fuse to see if the metal wire inside is separated. If it is, the fuse is blown and should be replaced. Fuse puller tool and fuse...
Page 253 Roadside Emergencies 4. Use the fuse puller tool to remove the blown fuse and replace the fuse with one that has the right amperage rating (see the fuse panel cover for amperage ratings). WARNING Always replace a fuse with one that has the specified amperage rating.
Page 254 Engine Compartment Main Fuse Panel Engine fuse block location Engine compartment main fuse panel...
Page 255 Roadside Emergencies...
Page 256 Circuit Breakers The circuit breakers will reset themselves and allow the electrical parts to work again once the overload on the circuit is removed. If the circuit breakers continue to cut off electricity, have your vehicle’s electrical system checked. If you have questions about circuit breakers or how to check them, see your Lincoln-Mercury dealer.
Page 257 Roadside Emergencies Relays Relays are devices which receive signals from components or systems. After receiving signals, relays transfer these signals to activate or deactivate other components or systems. A relay box is located near the windshield washer fluid reservoir. The relay box...
Page 258: Changing A Flat Tire
Changing a Flat Tire If you get a flat tire while you are driving, do not apply the brake heavily. Instead, gradually decrease the speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road.
Page 259 Roadside Emergencies drive through an automatic car wash. Because the temporary spare tire is smaller than a conventional tire, it reduces the ground clearance. Your vehicle may get caught in the rails and it could be damaged. Spare Tire Location The spare tire is stored underneath your vehicle.
Page 260 2. Find the lug wrench in the tool kit located behind the jack in the right cargo area side panel. Jack storage location...
Page 261 Roadside Emergencies 3. Fit the hex-shaped end of the lug wrench over the hex nut in the floor of the cargo area. Turn counterclockwise until the cable extends far enough to lower the spare tire to the ground. The spare tire in the lowered position 4.
Page 262 Stowing the spare tire 1. To raise the tire to the stowed position, lay the tire on the ground with the inboard side facing up. Install the retainer through the wheel center and slide the tire under the vehicle. Fit the hex-shaped end of the lug wrench over the hex nut in the floor of the cargo area.
Page 263 Roadside Emergencies WARNING To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed. WARNING If the vehicle slips off the jack, you or someone else could be seriously injured.
Page 264 3. Insert the tapered end of the jack handle behind the wheel cover of the tire to be changed and gently pry it off. When you want to replace the wheel cover, simply align the valve stem to the slot in the cover and press it back on. Removing the wheel cover...
Page 265 Roadside Emergencies If you have optional cast-aluminum wheels, remove the wheel cap to gain access to the lug nuts. Insert the tapered end of the jack handle behind the notch in the wheel cap and gently pry it off. To replace it, press it back on. You must line up the raised circle on the back of the wheel cap with the indented area on the wheel in order to press the wheel cap on.
Page 266 Anti-theft lug nut 5. Fit the jack under the proper jacking point indicated by the notch in the bottom of the door frame panel. The notches for the jack...
Page 267 Roadside Emergencies Placing the jack WARNING Do not jack on the running board. WARNING To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire. WARNING To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire.
Page 268 All of these tools are needed to jack up a vehicle. NOTE: If Ford Accessory Running Boards have been installed, use the jack adapters supplied with the running boards as described on the inside of the jack storage area cover.
Page 269 Roadside Emergencies 7. Turn the lug nut wrench (attached to the jack handle) clockwise to raise the vehicle off the ground. 8. Remove the wheel lug nuts with the lug nut wrench. 9. Remove the flat tire and replace it with the spare tire. 10.
Page 270 WARNING Never use wheels or lug nuts different than the original equipment as this could damage the wheel or mounting system. This damage could allow the wheels to come off while the vehicle is being driven. 13. Replace the wheel cover by pressing it into place. If you have the standard wheel covers, you must align the notch in the wheel cover with the tire’s valve stem and align the recess in the back of the wheel cover with one of the lug nuts.
Page 271 Roadside Emergencies Storing the jack 16. Make sure the lug wrench is secured back into the tool kit and store it next to the jack. 17. Unblock the wheels. Retighten the lug nuts to the specified torque at 500 miles (800 km) of operation, after any wheel change, or any time the lug nuts are loosened.
Page 272 Jump-Starting Your Battery Your vehicle’s battery may discharge if you leave the lights or any electrical equipment on after you turn the engine off. If this happens, you may be able to jump-start from a booster battery to start your vehicle. WARNING The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes.
Page 273 Roadside Emergencies To avoid damaging your vehicle or your battery, and to avoid injury to yourself, follow these directions for preparing your vehicle to jump-start and connecting the jumper cables in the order they are given. If in doubt, call for road service. Preparing Your Vehicle 1.
Page 274 Connecting the jumper cables 1. Connect one end of the first jumper cable to the positive (+) terminal of the discharged battery. (You can connect either jumper cable to the positive (+) terminal, as long as you use the same cable for both positive terminals.) Most jumper cables have a red cable and a black cable.
Page 275 Roadside Emergencies Sequence for connecting jumper cables...
Page 276: Towing Your Vehicle
If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. DO NOT TOW YOUR VILLAGER WITH SLINGBELT EQUIPMENT. Ford Motor Company has not developed or approved a T-hook sling-type procedure. Use wheel lift or flatbed equipment.
Page 277 Towing the vehicle When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for the proper hook-up and...
Page 278 Notes...
Page 279: Maintenance And Care
Maintenance and Care Service Made Easy Ford has two goals for servicing your vehicle. 1. When we can, we design parts that do not need to be serviced. 2. We want to make servicing your vehicle as easy as possible.
Page 280 NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for disposing of these types of fluids. Call your local recycling center to find out about recycling automotive fluids. Precautions When Servicing Your Vehicle Be especially careful when inspecting or servicing your vehicle. Here are some general precautions for your safety: Your vehicle is equipped with an automatic cooling fan.
Page 281 Maintenance and Care If you must work under the hood while the engine is running: Set the parking brake fully and make sure that the gearshift is securely latched in P (Park). This will prevent your vehicle from moving unexpectedly. WARNING Do not start your engine with the air cleaner removed and do not remove it while the engine is running.
Page 282 2. Go to the front of the vehicle and release the hood latch under the hood in the front center of the vehicle. 3. Lift the hood and release the prop rod from its retaining clip. Place the end of the prop rod in the prop rod hole provided on the underside of the hood.
Page 283 2. Try to lift the hood after closing it to be sure it is securely latched. Engine Oil Recommendations Ford oil specification is WSS-M2C153-G. Use SAE 5W-30 motor oil certified for gasoline engines by the American Petroleum Institute. Do not use supplemental engine oil additives, oil treatments or engine treatments.
Page 284: Checking Engine Oil
Checking Engine Oil Check the engine oil each time you fuel your vehicle. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3.
Page 285 Maintenance and Care Changing the Engine Oil and the Oil Filter Engine oil dipstick Refer to the Maintenance Schedule booklet for additional information. Follow these directions to change the engine oil and oil filter: 1. Turn the engine off after it has warmed up. 2.
Page 286: Brake Fluid
7. Refill the engine with a CERTIFIED engine oil of the preferred viscosity. Start the engine and check for leaks. Follow directions in Checking and adding engine oil to be sure the engine is filled to the proper level. WARNING Continuous contact with USED motor oil has caused cancer in laboratory mice.
Page 287 Maintenance and Care If the fluid is low, carefully clean and remove the filler cap from the reservoir. Fill the reservoir to the MAX line with Ford High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent fluid meeting Ford specification ESA-M6C25-A.
Page 288: Windshield Washer Fluid
Windshield Washer Fluid Check the level of the windshield washer fluid every time you stop for fuel, or when the warning light indicates low washer fluid. The reservoir for washer fluid is located in the engine compartment. This reservoir contains the fluid for both the windshield and liftgate washers.
Page 289: Engine Coolant
Maintenance and Care Use specially formulated windshield washer fluid rather than plain water, because specially formulated washer fluids contain additives that dissolve road grime. For safety reasons, washer fluids containing an appropriate antifreeze such as methanol should be used in freezing weather (temperatures below 32°...
Page 290 Adding Engine Coolant Engine coolant recovery reservoir WARNING Do not put engine coolant in the container for the windshield washer fluid. When the engine is cool, add a 50/50 mixture of engine coolant and water to the engine coolant recovery reservoir — DO NOT ADD DIRECTLY TO THE RADIATOR.
Page 291 Ford Specification ESE-M97B44-A. Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for 4 years or 50,000 miles (80,000 km). Do not use alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze.
Page 292 Recycled Engine Coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44-A, and use of such coolant may harm engine and cooling system components.
Page 293: Power Steering Fluid
Maintenance and Care Engine Coolant Drain and Flush To have your engine coolant drained, see your Ford or Lincoln-Mercury dealer or refer to the procedure in the Service Manual. Power Steering Fluid Check the level of the power steering fluid at least twice a year (i.e., every Spring and Fall).
Page 294 Refill Capacities, Motorcraft Parts, and Lubricant Specifications in the Capacities and Specifications chapter. Use only power steering fluid that meets Ford Specification such as MERCON ATF XT-2-QDX (or equivalent). NOTE: If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid.
Page 295: Automatic Transmission Fluid
Maintenance and Care Automatic Transmission Fluid Under normal circumstances, you do not need to check the fluid level of the transaxle since your vehicle does not use up transmission fluid. However, if the transaxle is not working properly (for example, slipping or shifting slowly), or you notice some sign of fluid leakage, the fluid level should be checked.
Page 296 Engine compartment main fuse panel When checking fluid at normal operating temperature, the fluid level should be within the crosshatched area on the dipstick. When the vehicle has not been driven, and outside temperature is above 50° F (10° C), the fluid level should be between the notches on the dipstick.
Page 297 Maintenance and Care Automatic transmission fluid dipstick NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for disposing of these types of fluids. Call your local recycling center to find out about recycling automotive fluids. NOTE: Always use Motorcraft MERCON or equivalent MERCON automatic transmission fluid when you refill your automatic transmission fluid.
Page 298 If the battery needs water often, have the charging system checked. Help Us Protect Our Environment Ford Motor Company strongly recommends that used lead-acid batteries be returned to an authorized recycling facility for disposal.
Page 299 Maintenance and Care WARNING The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. WARNING To protect yourself when charging a battery, always shield your face and eyes. Make sure that you can breathe fresh air.
Page 300: Air Filter
Air Filter Air filter housing The air filter should not be cleaned and reused. Replace it according to the maintenance intervals shown in the Maintenance Schedule booklet. When replacing the filter, unclip the four clamps and remove the filter. Wipe the inside of the air filter housing with a damp cloth when replacing the filter.
Page 301: Wiper Blades
Maintenance and Care Wiper Blades Check the windshield wiper blades at least twice a year. Also check them whenever they seem less effective than usual. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades. If the blades do not wipe properly, clean both the windshield and the wiper blades.
Page 302 To replace the wiper blades: 1. Pull the wiper arm away from the windshield and into the lock position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
Page 303 Maintenance and Care Tires Look at your tires each time you fill your fuel tank. If one tire looks lower than the others, check the pressure in all of them. Always follow these precautions: Use an accurate tire pressure gauge. Stay within the recommended load limits.
Page 304 WARNING Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control. Tire Inspection and Maintenance Inspect the tire treads and remove stones, nails, glass or other objects that may be wedged in the tread grooves. Check for holes or cuts that may permit air to leak from the tire and make the necessary repairs.
Page 305 Maintenance and Care Rotating the tires After each rotation, adjust individual tire pressure as specified on the Tire Pressure Decal. Tighten wheel lug nuts to the required torque specification and retighten again after 500 miles (800 km). If your vehicle has the optional full-size spare tire, you may rotate the spare tire into the rotation pattern.
Page 306 If you do not follow these precautions, your vehicle may not drive properly and safely. WARNING Make sure that all replacement tires are of the same size, type, load-carrying capacity, and tread design (e.g. “All Terrain”, etc.), as originally offered by Ford.
Page 307 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation — Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.
Page 308 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.
Page 309 The information on braking performance and tire quality grading found in the “Ford Motor Company Passenger Car Consumer Information” pamphlet (FPS 12024-92) also applies to the Villager. This publication is available from your dealer.
Page 310: Filling The Fuel Tank
Drive slowly. If you can hear the cables rub or bang against your vehicle, stop the vehicle and tighten the cables. If you continue to hear the cables rub or bang against your vehicle, remove the cables to prevent damage to your vehicle. Avoid fully loading your vehicle if possible.
Page 311 Maintenance and Care If you lose the fuel filler cap, replace it with an authorized Motorcraft or equivalent part. WARNING If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision.
Page 312 Before you fill your vehicle with fuel, extinguish all lit cigarettes, other smoking materials, and any open flames. To fill the tank properly: 1. Remove the fuel filler cap. Proceed to add fuel to the tank only if your vehicle is on level ground. 2.
Page 313 Maintenance and Care gasolines, the performance of the emission control devices and systems may be adversely affected. Repair of damage caused by using a fuel that your vehicle was not designed for may not be covered by your warranty. Octane recommendation Your vehicle is designed to use regular gasoline with an (R+M)/2 octane rating of 87.
Page 314 Gasolines for clean air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates such as a maximum of 10%ethanol or 15%MTBE. There should be no more than 5% methanol with cosolvents and additives to protect the fuel system.
Page 315 Maintenance and Care with a gasoline-methanol blend may cause the same kind of adverse reaction as drinking an alcoholic beverage. In sensitive individuals, serious personal injury or sickness could result. Consult a physician promptly if you experience an adverse reaction. Running Out of Fuel NOTE: Avoid running out of fuel because this situation may have an adverse effect on modern powertrain...
Page 316 Metric: L/100k = Multiply the number of liters used by 100 and divide the answer by the number of kilometers travelled. Comparisons With Environmental Protection Agency (EPA) Fuel Economy Estimates EPA fuel economy figures are obtained from laboratory tests under simulated road conditions and may not reflect the actual conditions you experience or your style of driving.
Page 317: Emission Control System
Maintenance and Care Emission Control System Your vehicle is equipped with a catalytic converter which enables your vehicle to comply with applicable exhaust emission requirements. WARNING Exhaust leaks may result in the entry of harmful and potentially lethal fumes into the passenger compartment. Under extreme conditions excessive exhaust temperatures could damage the fuel system, the interior floor covering, or other vehicle components, possibly...
Page 318 In general, maintenance, replacement, or service of the emission control devices or systems in your new Ford Motor Company vehicle or engine may be performed at your expense by any automotive repair establishment or individual using automotive parts equivalent to those with which your vehicle or engine was originally equipped.
Page 319 Maintenance and Care Do not drive your vehicle if it does not operate properly. See your dealer if the engine runs on for more than five seconds after you shut it off or if it misfires, surges, stalls, or backfires. Information about your vehicle’s emissions control system is on the Vehicle Emission Control Information decal located on or near the engine.
Page 320 Lights and Bulb Replacement It is a good idea to check the operation of the following lights frequently: headlamps high-mount brakelamp tail lamps brakelamps cornering lamps hazard flasher turn signals license plate lamps The alignment of your headlamps should be checked if: oncoming motorists frequently signal you to turn off your vehicle’s high beams when you do not have the high beams on...
Page 321 Maintenance and Care WARNING Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Page 322 3. Remove the bulb retaining ring by turning it counterclockwise 1/8 of a turn to free it from the socket. Then slide the ring off the plastic base. Keep the ring. You must use it again to hold the new bulb in place. Removing the headlamp bulb retaining ring 4.
Page 323 Maintenance and Care Headlamp bulb replacement Installing the headlamp bulb 1. With the flat side of the bulb’s plastic base facing upward, insert the glass end of the bulb into the socket. You may need to turn the bulb left or right to line up the grooves in the plastic base with the tabs in the socket.
Page 324 4. Turn the headlamps on and make sure that they work properly. If the headlamp was correctly aligned before you changed bulbs, you should not need to align it again. Replacing the Bulbs There are several different types of replacement bulbs for your vehicle.
Page 325 Maintenance and Care Bulb locations...
Page 326 Bulb replacement chart...
Page 327 Maintenance and Care...
Page 329 Maintenance and Care...
Page 331 Maintenance and Care...
Page 333: Cleaning Your Vehicle
Ford, however, believes that continual improvement in customer satisfaction is a high priority. For this reason, Ford has authorized their dealers to repair, at no charge to the owner,...
Page 334 Cleaning Chrome and Aluminum Parts Wash chrome and aluminum parts with a mild detergent. Do not use steel wool, abrasive cleaners, fuel or strong detergents. Cleaning Plastic Parts Some of your vehicle’s exterior trim parts are plastic. Clean with a tar and road oil remover if necessary. Use a vinyl cleaner for routine cleaning.
Page 335 Maintenance and Care Cleaning the Engine A clean engine is more efficient because a buildup of grease and dirt acts as an insulator, keeping the engine warmer than normal. Extreme care must be used if a power washer is used to clean the engine.
Page 336 Cleaning the Instrument Panel Lens Clean the instrument panel lens with a soft cloth and a glass cleaner, such as Ford Ultra-Clear Spray Glass Cleaner, or equivalent. Do not use paper towel or any abrasive cleaner to clean the lens as these may cause scratches.
Page 337: Vehicle Storage
Maintenance and Care Vehicle Storage Maintenance Tips If you plan on storing your vehicle for an extended period of time (60 days or more), refer to the following maintenance recommendations to keep your vehicle in good operating condition. General Store your vehicle in a dry, ventilated place. Protect from sunlight, if possible.
Page 338 Ford Gas Stabilizer should be added whenever actual or expected storage periods exceed 60 days. Follow the instructions on the label. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system.
Page 339 Maintenance and Care Cooling system Protect your vehicle against freezing temperatures. Battery Check and recharge the battery as necessary. Keep connections clean and covered with a light coat of grease. Brakes Make sure the brakes and parking brake are fully released. Tires Maintain recommended air pressure.
Page 340 Notes...
Page 341: Capacities And Specifications
Capacities and Specifications Refill Capacities, Motorcraft Parts, and Lubricant Specifications Motorcraft Parts...
Page 343 Capacities and Specifications Lubricant Specifications Automatic Transmission Fluid...
Page 345: Engine Compartment
Capacities and Specifications Engine Compartment Your vehicle has a 3.0 liter EFI, V-6 engine. The following illustration will show a diagram of your engine and where you can find items that you should service regularly. Automatic Transmission Fluid Dipstick Engine Coolant Reservoir Brake Fluid Reservoir Air Filter Battery...
Page 347: Reporting Safety Defects
National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 348 Notes...
Page 349: Customer Assistance
3 years or 36,000 miles (60,000 km), whichever comes first. To purchase Roadside Assistance coverages beyond this period (available through Ford Auto Club in the United States or Ford and Lincoln-Mercury dealers in Canada), contact your Ford or Lincoln-Mercury dealer. Additional Roadside Assistance coverage is unavailable in Puerto Rico and the Virgin Islands.
Page 350 Should you need to arrange for roadside assistance yourself, Ford Motor Company will reimburse the reasonable cost. To obtain information about reimbursement call 1-800-241-FORD (in Canada call 1-800-665-2006). If You Have a Service Concern Ford Motor Company has authorized Ford and Lincoln-Mercury dealerships to service your vehicle.
Page 351 If you live in the U.S. and have any questions or concerns that the dealership cannot answer, contact the Customer Assistance Center. To process your request, the Ford Customer Assistance Center needs the following information: your telephone number(s) (both business and home)
Page 352 The Dispute Settlement Board is: an independent, third-party arbitration program for warranty disputes available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or discontinue this service without notice and without incurring obligations.
Page 353 How does the Board work? The Board consists of: three consumer representatives a Ford or Lincoln/Mercury dealer Consumer candidates for Board membership are recruited and trained by an independent consulting firm. Dealers are chosen because of their business leadership qualities.
Page 354 Ford Motor Company the names (if known) of all the people you contacted at the...
Page 355 The Board also provides a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on the dealer and Ford, but not on consumers who may elect to pursue other remedies available to them under state and federal law.
Page 356 Mediation/Arbitration Program (Canada Only) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in...
Page 357 Use of leaded fuel in your vehicle without a proper conversion may damage the effectiveness of your emissions control system and may cause engine knocking or serious engine damage. Ford Motor Company is not responsible for any damage that is caused...
Page 358 U.S.A. Telephone: (313) 594-4857 Fax: (313) 390-0804 If you are in other foreign countries, contact the nearest Ford dealership. If the dealership cannot help you, they can direct you to the appropriate Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S.
Page 359: Accessories
Accessories Ford Accessories for Your Villager Ford has many fine products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following, or products of equivalent quality: Many accessories for your vehicle are available through your local authorized dealer.
Page 360 Safety, Comfort, and Convenience Comfort and Convenience Air Conditioning Engine Block Heater Remote Keyless Entry Protection and Appearance Equipment Aero Running Boards Carpeted Floor Mats Door Edge Guards Cleaners, Waxes and Polishes Front End Cover Front End Mini Cover Lubricants and Oils Molded Running Boards Rear Air Deflector Side Window Shields...
Page 361 In addition, to insure continued compliance with the FCC’s requirements, RF devices must not be modified or changed in a manner not expressly approved by Ford Motor Company.
Page 362 5 watts or less, ordinarily will not affect vehicle operation.) NOTE: Because Ford has no control over the operation or manufacture of such systems or their installation, Ford cannot assume responsibility for any adverse effects...
Page 363 Accessories...
Page 364 Notes...
Page 365 Accessories Notes...
Page 366 Notes...
Page 377: Index
Index Accessory position on the ignition ....86 Air bag supplemental restraint system ... 144 and child safety seats .
Page 378 Automatic transmission driving an automatic overdrive ....223 fluid, adding ..... . . 291 Backing up .
Page 379 Index servicing ..... . 217, 282 stopping distances ....218 trailer .
Page 380 Chime headlamps on ..... . . 18 safety belt ......11 Circuit breakers checking and replacing .
Page 381 Cooling fan ......276 Customer Assistance Centre, Ford of Canada ..352 Daytime running light system .
Page 382 Electrical system circuit breakers ..... . 252 fuses ......243, 244 relays .
Page 383 Flat tire ......254 Ford Dispute Settlement Board ....348...
Page 384 Ford Motor Company of Canada ....352 Ford of Canada Customer Assistance Centre ..352 Foreign registration ..... 353 French owner guides, how to obtain .
Page 385 Index Fuses charts ......244 checking and replacing ....243, 244 circuit breakers .
Page 386 GVWR (Gross Vehicle Weight Rating) ... . 226 calculating ......231 definition .
Page 387 Index Ignition positions of the ignition ....86 Infant seats (see Safety seats) ....151, 153 Instrument panel cleaning .
Page 388 Lights, warning and indicator air bag ......11 brake ......9 charging system .
Page 389 Index Mileage, calculating fuel economy ....311 Mirrors ......109 automatic dimming rearview mirror .
Page 390 driving with power steering ....220 fluid, checking and adding ....289 fluid, specifications .
Page 391 Index for children ..... . . 151 for infants ..... . 151, 153 for pregnant women .
Page 392 changing the tire ....254, 258 conventional spare ....254, 255 finding the spare .
Page 393 Index Tail lamps bulb replacement ....316, 322 cleaning ......330 Temperature control (see Climate control) .
Page 394 Transmission automatic operation ....221 Transmission control switch ....223 Trip odometer .
Page 395 Index Wheel dollies (see Towing) ....272 Wheels ......303 anti-theft lugnuts .
Page 400: Service Station Information
Service Station Information...

This manual is also suitable for:

1998 mercury villager Villager

Ford Mercury Villager 1997 Owner's Manual

Quick Links

Related Manuals for Ford Mercury Villager 1997

Summary of Contents for Ford Mercury Villager 1997

This manual is also suitable for:

Table of Contents