Troubleshooting - Pro-Form 6.0 Rt Treadmill Manual
English manual
Hide thumbs
Also See for 6.0 Rt Treadmill:
- User manual (28 pages) ,
- User manual (28 pages) ,
- User manual (28 pages)
Table of Contents
Advertisement
TROUBLESHOOTING
Most treadmill problems can be solved by follow-
ing the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assis-
tance is needed, see the front cover of this manual.
SYMPTOM: The power does not turn on
a. Make sure that the power cord is plugged into a
surge suppressor and that the surge suppressor is
plugged into a properly grounded outlet (see page
14). Use only a surge suppressor that meets
all of the speci cations described on page 14.
IMPORTANT: The treadmill is not compatible
with GFCI-equipped outlets and may not be
compatible with AFCI-equipped outlets.
b. After the power cord has been plugged in, make
sure that the key is inserted into the console.
c. Check the power switch located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
power switch, wait for ve minutes and then press
the switch back in.
c
Tripped
SYMPTOM: The power turns off during use
a. Check the power switch (see the drawing above).
If the switch has tripped, wait for ve minutes and
then press the switch back in.
b. Make sure that the power cord is plugged in. If the
power cord is plugged in, unplug it, wait for ve
minutes, and then plug it back in.
Reset
21
c. Remove the key from the console, and then
reinsert it.
d. If the treadmill still will not run, please see the front
cover of this manual.
SYMPTOM: The console displays remain lit when
you remove the key from the console
a. The console features a display demo mode,
designed to be used if the treadmill is displayed in
a store. If the displays remain lit when you remove
the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a
few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 19 to turn off
the demo mode.
SYMPTOM: The incline of the treadmill does not
change correctly
a. Hold down the Stop button and the Speed increase
button, insert the key into the console, and then
release the Stop button and the Speed increase
button. Press the Stop button and then press the
Incline increase or decrease button. The tread-
mill will automatically rise to the maximum incline
level and then return to the minimum level. This will
recalibrate the incline system. If the incline does not
begin calibrating, press the Stop button again, and
then press the Incline increase or decrease button
again. When the incline is calibrated, remove the
key from the console.
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the 6.0 Rt Treadmill and is the answer not in the manual?
Questions and answers
the track is stuck in an incline position and the display continues to move through the various speed settings but none of the buttons can be activated. to lower the tack or start and stop any function. while in a programed mode I increased and lowered thespeed and now nothing works
To fix a stuck incline on a Pro-Form 6.0 RT Treadmill when the display is unresponsive, follow these steps:
1. Hold down the Stop button and the Speed increase button.
2. Insert the key into the console.
3. Release the Stop button and the Speed increase button.
4. Press the Stop button again.
5. Press the Incline increase or decrease button.
The treadmill will automatically rise to the maximum incline level and then return to the minimum level to recalibrate the incline system. If the incline does not begin calibrating, repeat steps 4 and 5. Once the calibration is complete, remove the key.
This answer is automatically generated
Does Proform 6.0 RT model require user to lubricate the motor belt?