Sony DXC-D35 Service Manual page 32

Shooting with the DSR-1/1P
The DXC-D35/D35P/D35WS/D35WSP docks with
the DSR-1/1P to configure a DVCAM Camcorder.
The following describes how to shoot using a
DVCAM camcorder.
Using the ClipLink Function
The ClipLink function can be used at all stages from
shooting to editing. This function makes editing
operations more efficient by automatically recording
index pictures (Mark IN point images) that provide a
searchable index of recorded scenes, along with other
data such as time code and scene numbers.
For concept of the ClipLink function, see the section "What
Is ClipLink"(page 102).
1
Dock the DSR-1/1P to the camera head and turn on
the power, then perform steps 2 to 10 from "Basic
Procedure for Shooting" (page 43).
2
Insert a cassette into the DSR-1/1P and set
ClipLink mode to ON by menu setting.
For details of this operation, see the operating
instructions for the DSR-1/1P.
The following display appears on the viewfinder
screen.
TCG 12:34:56:00
W:A
ClipLink mode indication:
CLIP M or C a) CLIPM
198 F5.6
Clip remaining:
56ND
99 04 01
Indicates the number of
10:10 AM
available Index pictures
(198 max.)
a) For details, see "Basic menu page 6" (page 60).
To record the cassette name/number
Access basic menu page 6 to specify a name or
number for the inserted cassette.
For details, see "Basic menu page 6" (page 60).
46
Chapter 3 Shooting
3
Press the VTR button on the camera head or the
lens.
The DSR-1/1P starts recording, and the REC/
TALLY indicator lights in the viewfinder.
Meanwhile, the time code at the recording start
point (Rec IN) is recorded (HH:MM:SS) in the
DSR-1/1P's internal memory.
4
When a shooting of the scene completes, press the
VTR button on the camera head or the lens.
This pauses recording.
To continue recording the next scene, repeat steps
3 and 4. The scene number will be automatically
incremented.
To set/clear NG (No Good)
If you press the NG button before you start
shooting the next scene, the previous scene will be
designated as "NG" (the "NG" display appears in
the viewfinder).
Once NG has been set, you can cancel it by
pressing the NG button again before you start
shooting the next scene (the "NG" display in the
viewfinder disappears, which means that the
previous scene has been re-designated as "OK").
Each time you press the NG button before starting
shooting the next scene, the status of the previous
scene toggles between "NG" and "OK". It is
always the last selected status that will take effect
and be stored in the cassette memory.
5
To finish recording, press the STOP button on the
DSR-1/1P.
This stops recording.
Note
When using the ClipLink function while shooting, if
you continue shooting after stopping or if you change
the tape's recording position, your subsequent shots
may overwrite and erase the previously recorded
ClipLink log data (time codes, scene number, etc.) or
index pictures.
To avoid this problem, press the DSR-1/1P's ClipLink
CONTINUE button before restart of shooting.
For details, see the operating instructions for the DSR-1/1P.
Setting Mark IN/OUT points as you shoot
Instead of continuing shots from scene to scene, you
can specify Mark IN and Mark OUT points as you
shoot and set scene numbers (ranging from 001 to
198).
1
Perform steps 1 and 2 from "Using the ClipLink
Function" (page 46).
2
Access basic menu page 6 and perform the
following operations.
1) Set MARK/CUE to MARK.
The ClipLink mode indication "CLIP M"
appears on the viewfinder screen.
2) Set the cassette name or number if necessary.
For details of menu operations, see "Basic Menu
Operations" (page 58).
3
Press the VTR button on the camera head or the
lens.
The DSR-1/1P starts recording, and the REC/
TALLY indicator(s) light(s) in the viewfinder.
4
Press the TAKE button when you find a shot
where you would like to set a Mark IN point.
TAKE button
The TAKE/TALLY indicator (orange) lights in the
viewfinder and "TAKE" appears on the screen.
5
Press the TAKE button when you find a shot
where you would like to set a Mark OUT point.
The TAKE/TALLY indicator (orange) goes out in
the viewfinder and the "TAKE" disappears from
the screen.
At this time, the time code (HH:MM:SS) at the
Mark IN/OUT point for scene 001 is recorded to
the DSR-1/1P's internal memory, and then
recorded to the cassette memory.
To set/clear NG
If you press the NG button before you set the next
Mark IN point, the previous scene will be
designated as "NG" (the "NG" display appears in
the viewfinder).
Once NG has been set, you can cancel it by
pressing the NG button again before you set the
next Mark IN point (the "NG" display in the
viewfinder disappears).
6
Repeat steps 4 and 5 as needed to record (to
cassette memory) time codes at Mark IN/OUT
points, scene numbers, and NG designations to the
cassette memory.
The scene number is automatically incremented
each time you specify a Mark OUT point.
7
To finish shooting, press the VTR button on the
camera head or the lens, then press the DSR-1/1P's
STOP button.
This stops the recording operation.
The index pictures of each Mark IN point are
recorded onto the tape.
47
Chapter 3 Shooting