Table of Contents
Advertisement
The P-ATA+S-ATA and P-ATA options are for advanced users only. If
you set to any of these options and encountered problems, revert to
the default setting S - A T A
[S-ATA] [P-ATA]
The O n b o a r d I D E O p e r a t e M o d e
O n b o a r d I D E O p e r a t e M o d e
O n b o a r d I D E O p e r a t e M o d e
O n b o a r d I D E O p e r a t e M o d e
O n b o a r d I D E O p e r a t e M o d e and its sub-menu items appear
only when the C o n f i g u r e S A T A A s
Onboard Serial-ATA BOOTROOM [Enabled]
Enables or disables the onboard Serial ATA boot ROM. This item
appears only when the Configure SATA As item is set as RAID.
Configuration options: [Disabled] [Enabled]
The O n b o a r d S e r i a l - A T A B O O T R O M
O n b o a r d S e r i a l - A T A B O O T R O M
O n b o a r d S e r i a l - A T A B O O T R O M appears only when the
O n b o a r d S e r i a l - A T A B O O T R O M
O n b o a r d S e r i a l - A T A B O O T R O M
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s item is set to [RAID].
C o n f i g u r e S A T A A s
ALPE and ASP [Disabled]
ALPE and ASP [Disabled]
ALPE and ASP [Disabled]
ALPE and ASP [Disabled]
ALPE and ASP [Disabled]
Allows you to enable or disable the Agressive Link Power Management
(ALPE) and Aggressive Slumber/Partial (ASP) management features.
Configuration options: [Disabled] [Enabled]
Stagger Spinup Support [Enabled]
Enables or disables the stagger spinup support.
Configuration options: [Disabled] [Enabled]
AHCI Port 3 Interlock Switch [Disabled]
Enables or disables the Advanced Host Controller Interface (AHCI) Port
3 interlock switch. Configuration options: [Disabled] [Enabled]
The A L P E a n d A S P
A L P E a n d A S P
A L P E a n d A S P
A L P E a n d A S P and its sub-menu appear only when the
A L P E a n d A S P
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s item is set to [AHCI].
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
IDE Detect Time Out [35]
IDE Detect Time Out [35]
IDE Detect Time Out [35]
IDE Detect Time Out [35]
IDE Detect Time Out [35]
Selects the time out value for detecting ATA/ATAPI devices.
Configuration options: [0] [5] [10] [15] [20] [25] [30] [35]
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
S - A T A. Configuration options: [P-ATA+S-ATA]
S - A T A
S - A T A
S - A T A
C o n f i g u r e S A T A A s item is set to [Standard IDE].
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
4 - 1 7
4 - 1 7
4 - 1 7
4 - 1 7
4 - 1 7
Advertisement
Table of Contents
