Table of Contents
Advertisement
3 . 3 .
3 .
3 .
3 .
I D E R A I D c o n n e c t o r s ( 4 0 - 1 p i n P R I _ R A I D 1 [ r e d ] ,
I D E R A I D c o n n e c t o r s ( 4 0 - 1 p i n P R I _ R A I D 1 [ r e d ] ,
I D E R A I D c o n n e c t o r s ( 4 0 - 1 p i n P R I _ R A I D 1 [ r e d ] ,
I D E R A I D c o n n e c t o r s ( 4 0 - 1 p i n P R I _ R A I D 1 [ r e d ] ,
I D E R A I D c o n n e c t o r s ( 4 0 - 1 p i n P R I _ R A I D 1 [ r e d ] ,
S E C _ R A I D 1 [ r e d ] )
S E C _ R A I D 1 [ r e d ] )
S E C _ R A I D 1 [ r e d ] )
S E C _ R A I D 1 [ r e d ] )
S E C _ R A I D 1 [ r e d ] )
These connectors are for Ultra ATA 133/100/66 signal cables. The
IDE RAID connectors support up to four IDE hard disk drives that you
can configure as a disk array through the onboard IDE RAID controller.
Refer to Chapter 5 for details on how to set up RAID configurations.
These connectors are set to I D E
can connect IDE devices to these connectors such as boot/data hard disk
drives or optical drives. If you intend to create an IDE RAID set using these
connectors, set the I T E 8 2 1 2 F C o n t r o l l e r
Mode]. See section "4.4.6 Onboard Devices Configuration" for details.
P5AD2
P5AD2 Deluxe IDE RAID connectors
•
Before creating a RAID set using Ultra ATA hard disks, make sure
that you have connected the Ultra ATA signal cable and installed Ultra
ATA 133/100/66 hard disk drives.
•
The system automatically assigns the boot sequence of ATAPI
devices connected to the IDE RAID connectors.
•
The ITE
hard disk drives in RAID 1 configuration.
•
Before creating a RAID 1 set, make sure that you set the hard disk
drives as either Master or Slave device. Refer to the hard disk drive
documentation for details.
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
I D E
I D E M M M M M o d e
I D E
I D E
I T E 8 2 1 2 F C o n t r o l l e r item in the BIOS to [RAID
I T E 8 2 1 2 F C o n t r o l l e r
I T E 8 2 1 2 F C o n t r o l l e r
I T E 8 2 1 2 F C o n t r o l l e r
NOTE: Orient the red markings
(usually zigzag) on the IDE
cable to PIN 1.
PRI_RAID1
®
8212F controller supports a maximum of two Ultra ATA
o d e
o d e
I D E M M M M M o d e
I D E
I D E
o d e by default. In I D E
o d e
I D E
SEC_RAID1
PIN 1
o d e
o d e
o d e, you
o d e
2 - 2 3
2 - 2 3
2 - 2 3
2 - 2 3
2 - 2 3
Advertisement
Table of Contents
