Table of Contents
Advertisement
5 . 5 .
5 .
5 .
5 .
S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 ,
S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 ,
S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 ,
S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 ,
S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 ,
S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 )
S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 )
S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 )
S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 )
S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 )
These connectors are for Serial ATA signal cables. These connectors
support up to four Serial ATA hard disk drives that you can configure
as a disk array through the onboard SATA RAID controller. Refer to
Chapter 5 for details on how to set up Serial ATA RAID configurations.
These connectors are set to R A I D M o d e
connect Serial ATA boot/data hard disk drives to these connectors, set
the S i l i c o n I m a g e C o n t r o l l e r
S i l i c o n I m a g e C o n t r o l l e r
S i l i c o n I m a g e C o n t r o l l e r
S i l i c o n I m a g e C o n t r o l l e r item in the BIOS to [SATA Mode]. See
S i l i c o n I m a g e C o n t r o l l e r
section "4.4.6 Onboard Devices Configuration" for details.
P5AD2
P5AD2 Deluxe SATA RAID connectors
•
Before creating a RAID set using Serial ATA hard disks, make sure
that you have connected the Serial ATA signal cable and installed
Serial ATA hard disk drives; ; otherwise, you cannot enter the Silicon
Image RAID utility and SATA BIOS setup during POST.
•
You can only create RAID 5 and JBOD configuration using the
SATALink™ SATA RAID Management software. See Chapter 5 for
details. The RAID 5 feature is not Windows
(WHQL)-certified.
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
A S U S P 5 A D 2 D e l u x e
R A I D M o d e
R A I D M o d e
R A I D M o d e by default. If you want to
R A I D M o d e
SATA_RAID1 SATA_RAID2 SATA_RAID3 SATA_RAID4
®
Hardware Quality Labs
2 - 2 5
2 - 2 5
2 - 2 5
2 - 2 5
2 - 2 5
Advertisement
Table of Contents
