Gas Conversion Kits - Lennox EDV3530CNM-B Installation Instructions Manual

GAS CONVERSION KITS

This conversion kit shall be installed by a qualified service agency in accor-
dance with the manufacturer's instructions and all applicable codes and
requirements of the authority having jurisdiction. If the information in these
instruction is not followed exactly, a fire, explosion or production of carbon
monoxide may result causing property damage, personal injury or loss of
life. The qualified service agency is responsible for the proper installation
of this kit. The installation is not proper and complete until the operation
of the converted appliance is checked as specified in the manufacturer's
instructions supplied with the kit.The qualified service agency performing
this installation assumes responsibility for this conversion.
Cette trousse de conversion doit être installée par un technicien agréé,
selon les instructions du fabricant et selon toutes les exigences et tous les
codes pertinents de l'autorité compétente. Assurez-vous de bien suivre
les instructions dans cette notice pour réduire au minimum le risque
d'incendie, d'explosion ou la production de monoxyde de carbone pouvant
causer des dommages matériels, des blessures ou la mort. Le tecnicien
agréé est responsable de l'installation de cette trousse. L'installation n'est
pas adéquate ni complète tant que le bon fonctionnement de l'appareil
converti n'a pas été vérifié selon les instructions du fabricant fournies avec
la trousse. Le fournisseur de service qualifié ayant réalisé l'installation
assume les responsabilités liées à la conversion.
In Canada:
THE CONVERSION SHALL BE CAR-
RIED OUT IN ACCORDANCE WITH THE
REQUIREMENTS OF THE PROVINCIAL
AUTHORITIES HAVING jURISDICTION
AND IN ACCORDANCE WITH THE RE-
QUIREMENTS OF THE CAN/CSA-B149.1
INSTALLATION CODE.
LA CONVERSION DEVRA êTRE EFFEC-
TUéE CONFORMéMENT AUX RECOM-
MANDATIONS DES AUTORITéS PROVIN-
CIALES AYANT jURIDICTION ET CON-
FORMéMENT AUX EXIGENCES DU CODE
D'INSTALLATION CAN/CSA-B149.1.
Gas conversion kits are available to adapt your
appliance from the use of one type of gas to
the use of another. These kits contain all the
necessary components needed to complete the
task including labeling that must be affixed to
ensure safe operation.
Kit part numbers are listed here and the follow-
ing steps detail the conversion procedure. Refer
to the instructions provided with the conversion
kit when performing any gas conversion.
36
WARNING
AVERTISSEMENT
Millivolt SIT Systems
Natural Gas To Propane Gas
Conversion Kits
Models
EDV3530
EDV4035
EDV4540
Millivolt SIT Systems
Propane Gas to Natural Gas
Conversion Kits
Models
EDV3530
EDV4035
EDV4540
Electronic HONEYWELL Systems
Natural Gas To Propane Gas
Conversion Kits
Models
EDV3530
EDV4035
EDV4540
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Electronic HONEYWELL Systems
Models
EDV3530
EDV4035
EDV4540
INSTALLATION INSTRUCTIONS
Step 1. TURN OFF THE GAS SUPPLY TO THE
APPLIANCE and disconnect power supply at the
circuit breaker. Ensure appliance is cold.
CAUTION: THE GAS SUPPLY SHALL BE
SHUT OFF PRIOR TO DISCONNECTING THE
ELECTRICAL POWER, BEFORE PROCEED-
ING WITH THE CONVERSION.
ATTENTION: AVANT D'EFFECTUER
LA CONVERSION, COUPEZ D'ABORD
L'ALIMENTATION EN GAZ, ENSUITE,
COUPEZ L'ALIMENTATION éLECTRIQUE.
Open the bottom drop-down door. Open it (see
Figure 51 on page 26 ) by pushing in simultane-
ously the left and right top corners of the door.
(The door is hinged at the bottom.) Remove the
bottom compartment door by sliding the hinge
pin, located at the door's left side, to the right
until it disengages from the left corner post
hole. Pull the door diagonally to the left, away
from the fireplace.
Remove the modesty panel. To remove the
Catalog No.
modesty panel lift the modesty panel by the
85L62
tab on the panel's right end, pull the right end
85L63
of the panel away from cabinet and then pull the
panel diagonally out of the corner post slots on
85L64
the left side of the unit. Remove the modesty
panel carefully, so that none of the wires become
loose or disconnected. Remove the front glass
door/frame from the appliance.
Catalog No. Step 2. Carefully remove the logs. Exercise
care so as not to break the logs.
85L69
85L70
Step 3. Refer to Figure 63.
85L71
A. Above the burner, remove the two baffle
securing screws. Remove the baffle.
B. Remove the two screws securing the trap-
ezoidal plate to the burner. Remove the plate.
Catalog No.
C. Remove the burner assembly with attached
85L76
venturi tube.
85L77
85L78
Propane Gas To Natural Gas
Conversion Kits
Catalog No.
85L83
85L84
85L85