Step 5. Field Wiring - Lennox EDV3530CNM-B Installation Instructions Manual

Step 5. FIELD WIRING

CAUTION
Ground supply lead must be con-
nected to the wire attached to the
green ground screw located on the
outlet box. See
Figures 47 & 48
ure to do so will result in a potential
safety hazard. The appliance must be
electrically grounded in accordance
with local codes or, in the absence of
local codes, the National Electrical
Code, ANSI/NFPA 70-latest edition.
(In Canada, the current CSA C22-1
Canadian Electrical Code).
CAUTION: Label all wires prior to disconnec-
tion when servicing controls. Wiring errors can
cause improper and dangerous operation.
ATTENTION: Au moment de l'entretien des
commandes, étiquetez tous les fils avant de
les débrancher. Des erreurs de cáblage peu-
vent entraîner un fonctionnement inadéquat
et dangereux.
Verify proper operation after servicing.
S'assurer que l'appareil fonctionne adé-
quatement une fois l'entretien terminé.
WIRING DIAGRAM MILLIVOLT GAS VALVES
THERMOPILE
APPLIANCE- MOUNTED
ON/OFF SWITCH
(OPTIONAL)
TP-TH
TH
BK/W(1) BK/W(1)
WALL-MOUNTED ON/OFF SWITCH (OPTIONAL)
THERMOSTAT (OPTIONAL)
WALL MOUNTED CONFIGURATION FOR FAN SWITCH (OPTIONAL)
FAN
(OPTIONAL)
Figure 46
24
1. If any of the original wire as supplied must be replaced,
1. it must be replaced with Type AWM 105°C – 18 GA. wire.
2. 120V, 60Hz – Less than 3 amps.
**ON/OFF Switch (Integral
. Fail-
BK
W
*Blower speed control switch is provided in FBK200 blower kit.
Figure 47
Showing the Blower Wiring for the Optional
1. If any of the original wire as supplied must be replaced,
1. it must be replaced with Type AWM 105°C – 18 GA. wire.
2. 120V, 60Hz – Less than 3 amps.
*ON/OFF Switch (Integral
with Gas Valve)
TP
BK
GAS VALVE
WH
BK
R
W
GR
jUNCTION BOX
Figure 48
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Electronic Wiring Diagram (Honeywell)
Showing the Blower Wiring for the Optional
FBK-100 and FBK-200 Kits
**Leave the ON/OFF switch, which is integral
with the gas valve, in the ON position.
with Gas Valve)
Gas Valve
PILOT
ASSEMBLY
R
Green
BL
White
Black
OPT
BLOWER
Tab Intact
Tab
Broken
Red
Green
Neutral Hot
Ground
Side of
Side of
Screw
Receptacle Receptacle
W
Transf.
B
120 V.
G
24 V
BL
R
OPTIONAL APPLIANCE-MOUNTED ON/OFF SWITCH
OR OPTIONAL WALL SWITCH
OR OPTIONAL THERMOSTAT
OR OPTIONAL REMOTE RECEIVER
Factory Wired Field Wired
Schematic Representation Only
Electronic Wiring Diagram (Honeywell)
FBK-250 Kits
*Leave the ON/OFF switch, which is integral
with the gas valve, in the ON position.
Gas Valve
PILOT
ASSEMBLY
Optional
FBK-250
R
Module
BL
Green
White
Black
OPT
BLOWER
Tab Intact
Tab
Broken
Red
Green
Neutral Hot
Ground
Side of Side of
Screw
Receptacle Receptacle
W
B Transf.
120 V.
G
BL
R
OPTIONAL APPLIANCE-MOUNTED ON/OFF SWITCH
OR OPTIONAL WALL SWITCH OR OPTIONAL THERMOSTAT
OR OPTIONAL REMOTE RECEIVER
Factory Wired Field Wired
Schematic Representation Only
Refer to Section A for millivolt appliances and
Section B for electronic appliances. The gas
valve is set in place and pre-wired at the factory
on both models.
A. Millivolt Wiring (See Figure 46) –
1. Appliance-mounted ON/OFF burner control
switch (rocker switch) is factory installed in
the modesty panel. Optional wall-mounted
switch, thermostat, or one of the optional
remote control kits may also be used.
G o r n u - d G e r n e
N e t u a r - l W h e t i
120 VAC - Black
2. If wall-mounted ON/OFF control switch ther-
junction Box
mostat is selected, mount it in a convenient
location on a wall near the fireplace.
Optional
3. Wire the control switch within the millivolt
Accessory
Switch
control circuit using the 15 feet of 2 conductor
wire supplied with the unit.
Note: The supplied 15 feet of 2 conductor
wire has one end of each conductor con-
nected to the gas valve circuit and the other
BK
end of each conductor placed loose inside
the bottom compartment.
CAUTION: Do Not connect the optional wall
switch to a 120V power supply.
4. If an optional control switch is installed,
turn the appliance-mounted ON/OFF burner
control switch to the OFF position.
B. Electronic Wiring (See Figures 47 & 48) –
Note: The electronic appliance must be con-
nected to the main power supply.
1. Route a 3-wire 120Vac 60Hz 1ph power
supply to the appliance junction box.
2. Remove the electrical inlet cover plate from
the side of the unit by removing the plate's
G o r n u - d G e r n e
N u e a r t - l W h e t i
securing screws (see Figure 13 on Page
120 VAC - Black
10).
3. Remove the cover plate's knockout and
then feed the power supply wire through the
knockout opening and into the unit junction
junction Box
box.
4. Connect the black power supply wire to the
Optional
Accessory lower outlet's red pigtail lead and the white
Switch
power supply wire to the common terminal
of the outlet as shown in Figures 47 & 48.
5. Connect the ground supply wire to the pig-
tail lead attached to outlet's green ground
24 V
screw.
6. Appliance-mounted ON/OFF burner control
BK
switch (rocker switch) is factory installed
in the modesty panel.
Optional wall-mounted switch, thermostat, or
one of the optional remote control kits may
also be used. The appliance mounted ON/OFF
switch needs to be relocated onto the optional
style view door, if used.