1. Manuals
  2. Brands
  3. Lennox Manuals
  4. Indoor Fireplace
  5. Elite series
  6. Care and operation instructions manual

Lennox Elite Series Care And Operation Instructions Manual

B-vent gas fireplace heater inserts
Hide thumbs Also See for Elite Series:
Table of Contents

Advertisement

Quick Links

Installer: Leave This Manual With The Appliance.
Consumer: Retain This Manual For Future Reference.
A French manual is available upon request. Order P/N 775,155CF.
Ce manuel d'installation est disponible en francais, simplement
en faire la demande. Numéro de la pièce 775,155CF.
• Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will
retain heat for a while after shutting off the appliance. Severe burns may result.
• Carefully supervise children in the same room as appliance.
• If small children are present in the home, it is recommended that this appliance be fitted with a
screen door or screen panel kit. See Page 13 for ordering information.
• Suitable for installation into masonry or factory built fireplaces.
• Lennox™ gas-burning appliances are designed for use as a supplemental heater. They are not intended for
continuous use as a primary heat source.
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result
causing property damage, personal injury or loss
of life.
Do not store or use gasoline or other flammable
vapors or liquids in the vicinity of this or any other
appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not light any appliance.
• Do not touch any electrical switch; do not
Use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow your gas supplier's
instructions.
• If your gas supplier cannot be reached, call
the fire department.
Installation and service must be performed by a quali-
fied installer, service agency or the gas supplier
CARE AND OPERATION INSTRUCTIONS
B-Vent Gas
Fireplace Heater Inserts
P/N 775,155M Rev. E, 12/2007
US
Report No. 116-F-15-5
WARNINGS
AVERTISSEMENT: Assurez-vous de bien suivre les
instructions donné dans cette notice pour réduire au
minimum le risque d'incendie ou pour éviter tout dom-
mage matériel, toute blessure ou la mort.
POUR VOTRE SÉCURITÉ: Ne pas entreposer ni utiliser
d'essence ni d'autre vapeurs ou liquides inflammables dans
le voisinage de cet appareil ou de tout autre appareil.
POUR VOTRE SÉCURITÉ: Que faire si vous sentez une odeur
de gaz:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucun interrupteur. Ne pas vous servir
des téléphones se trouvant dans le batiment où vous
vous trouvez.
• Evacuez la piéce, le bâtiment ou la zone.
• Appelez immédiatement votre fournisseur de gaz depuis
un voisin. Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service dos incendies.
L'installation et service doit être exécuté par un qualifié instal-
.
leur, agence de service ou le fournisseur de gaz.
Models: EBVI25 & EBVI30

Advertisement

Table of Contents
loading

Related Manuals for Lennox Elite Series

Summary of Contents for Lennox Elite Series

  • Page 1 See Page 13 for ordering information. • Suitable for installation into masonry or factory built fireplaces. • Lennox™ gas-burning appliances are designed for use as a supplemental heater. They are not intended for continuous use as a primary heat source.

  • Page 2: Important Safety And Warning Information

    IMPORTANT SAFETY AND WARNING WARNING WARNING INFORMATION Carbon Monoxide Poisoning: Do not use these appliances if Early signs of carbon monoxide any part has been under water. READ THIS MANUAL IN ITS poisoning are similar to the flu Immediately call a qualified, ENTIRETY AND UNDER-STAND with headaches, dizziness and/or professional service technician...

  • Page 3: Table Of Contents

    MAnnually-Modulated Gas Valves and our environment. We extend our continued support to help you achieve the maximum benefit and enjoyment available from your new gas-fired heater. It is our goal at Lennox Nat. Gas Propane Hearth Products to provide you, our valued customer, with an appliance that will ensure Model No.

  • Page 4: Burn-In Period

    GAS CONTROLS CONTROL COMPARTMENT ACCESS Test gauge connections are provided on the front of the millivolt gas control valve (identi- Pull down hinged door to access control fied IN for the inlet and OUT for the manifold These millivolt appliances are fitted with a burner compartment (see Figure 3) side). See Figures 1 & 2. Off/On Switch, located on the side surround panel as shown in Figure 4 on Page 4. Once the Control Compartment Access pilot is lit, and valve knob is in the ON position, This appliance must be isolated from the the Off/On switch will control the appliance Pull down hinged door to access control compartment gas supply piping system (by closing its...

  • Page 5: Operation & Care Of Your Appliance

    OPERATION AND CARE OF YOUR WARNING IMPORTANT APPLIANCE Turn off gas and electrical power Do not use abrasive cleaners Appliance operation may be controlled before servicing the appliance. on glass. Never clean the glass through a remotely located optional wall thermostat or remote control.
  • Page 6 Connections use factory supplied powdercoat paint kit for Figure 7 touch-ups, cat. no. 90L74. Do not attempt to repaint the insert until the Model EBVI30 finish is completely cured (see Burn-In Period Spill Switch on Page 4). If the surface later becomes stained or marred, it may be lightly sanded and touched Figure 10 Remove  Screws up with spray paint. Paint is available at your local authorized Lennox Hearth Products dealer. Never attempt to paint a hot insert. Inspect Wiring Lift Out Air Duct Channel Inspect and clean all wire connections. Ensure that there is no melting or damage. Inspection should include: • Terminals at the valve Figure 8 • Off/On switch • Wall thermostat, remote control, or control kit (optional parts) • Spill switch...

  • Page 7: Maintenance Schedule

    MAINTENANCE Annually (Before the onset of the Burning Season) Maintenance Task Accomplishing Person Procedure Inspecting/Cleaning Burner, Logs Qualified Service Technician Inspect valve and ensure it is properly operating. Check piping and Controls for leaks. Vacuum the control compartment, fireplace logs and burner area. Check Flame Patterns and Flame Qualified Service Technician Refer to Figure 13 on Page 8 and verify the flame pattern and Height height displayed by the appliance conforms to the picture. Flames must not impinge on the logs. Inspecting/Cleaning Pilot and Burner Qualified Service Technician Refer to Figure 13 on Page 8 and Figure 25 on Page 12. Remove any surface build-up on pilot and burner assembly. Wipe the pilot nozzles, ignitor/flame rod and hood. Ensure the pilot flame engulfs the flame sensor as shown.

  • Page 8: Front Glass Door Assembly, Removal And Installation

    PROCEDURE FOR REMOVING STANDARD BURNER ADJUSTMENT GLASS DOOR ASSEMBLY Flame Appearance and Sooting Proper flame appearance is a flame which is blue at the base and becomes WARNING yellow/orange in the top of the flame. When the insert is first lit, the entire flame may be blue and will graduallay turn yellow/orange during the first 6-8 minutes of operation. If after 6-8 minutes the flame stays blue, or if Handle glass door with extreme care! The glass the flame is orange with evidence of sooting (black tip), the air shutter door assembly is susceptible to damage. Do not may require adjustment. scratch while handling or while reinstalling. An appliance operated with an air shutter opening that is too large will exhibit flames that are blue and transparent. These weak, blue and transparent flames are termed anemic. If the air shutter opening is too...

  • Page 9: Log Placement Instructions

    Burner Adjustment Procedure CAUTION WARNING Carbon will be produced if the air shutter is closed too much. Any damage due to carboning resulting from improperly setting the air Air shutter adjustment should shutter is not covered under the warranty. only be performed by a qualified professional service technician.
  • Page 10 1. Place the rear log onto the two corresponding locating pins at the 4. Place the Front Left Log onto the two corresponding locating pins back of the firebox as shown in Figure 16. as shown in Figure 19. Figure 16 Rear Log Figure 19 Front Left Log . Place the Front Right Log onto the two corresponding locating pins 5. Install the Top Left Log onto the corresponding locating pin and as shown in Figure 17. indentation on Center Log as shown in Figure 20. Figure 20 Top Left Log Figure 17 Front Right Log 6. Install the Front Center Log over the Front Right Log. The front 3. Place the Center Log onto the two corresponding locating pins as of log will rest on the burner and the back of log will rest on rear shown in Figure 18. log as shown in Figure 21. Figure 18 Center Log Figure 21 Front Center Log 7. Install the Top Right Log into the corresponding indentations on Front Center Log and front right twig as shown in Figure 22. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
  • Page 11 Embers Figure 23 9. Place some vermiculite around the logs as shown in Figure 24 (the entire bag of vermiculite will NOT be used). Top Right Log Figure 22 8. Place the glowing embers on the burner as shown in Figure 23. One package of ember material has been included with this log set You will not need to use the entire bag. IMPORTANT: The quantity and placement of the ember material can affect insert performance therefore it is very important that it be placed as shown in Figure a. Unpackage and divide the fine ember material (mineral wool) into dime-sized fluffy pieces. Figure 24 Vermiculite b. Distribute the pieces over the top of the front burner ports, filling the area in front of the forward logs.

  • Page 12: Millivolt Appliance Checkout

    AND SHOULD BE INSPECTED BY A QUALI- control switch. FIED PERSON PRIOR TO RE-USE AS A CONVENTIONAL FIREPLACE. With proper care and maintenance, your appli- ance will provide many years of enjoyment. If Fan Disc Figure 26 you should experience any problem, first refer to the troubleshooting guide in this manual. If problem persists, contact your Lennox Hearth WIRING DIAGRAMS Products Dealer. Wiring diagrams are provided here for refer- BLOWER OPERATION ence purposes only. This information is also provided on schematics attached directly to the When the insert heats up, the blower will auto- appliance on a pullout panel located within the matically be turned on by the fan disc located control compartment. under the firebox bottom on the front left side.

  • Page 13: Accessory Components

    Deluxe Remote Control System Screen Door Kit SIT & Honeywell The Model RCL-T (Deluxe) Remote Control Millivolt Wiring Diagram These decorative screen door panels fit over System has all of the features of the standard the standard glass door panels. system along with an added easy to read LCD If original wire as supplied must be replaced, it must be screen which presents access to many enhance- replaced with Type AWM 105°C, 18 gauge wire. ments, including; battery power level indicator, timer, mode of operation, thermostatic display including room temperature in either metric...
  • Page 14 Beveled Surround Kits Hearth Riser Kits ACCESSORY COMPONENTS These beveled surround panels install around The hearth riser trim kits are designed to be Wall Thermostat the insert body providing an attractive finished used with the optional surround kits (sold look. separately). It provides a finished look below The wall thermostat kit provides temperature the insert face when installed into fireplaces with a elevated firebox. control for optimum comfort. Insert Surround Hearth Riser Trim Panel Sizes Panels are available in 1”, 3” & 6” heights SKS-25 = 41 1/16"...

  • Page 15: Lighting Instructions - Millivolt

    LIGHTING INSTRUCTIONS – MILLIVOLT GAS VALVE FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. A. This appliance has a pilot which must be lighted with a piezo • Do not use any phone in your building. igniter. When lighting the pilot, follow these instructions • Immediately call your gas supplier from a neighbor’s exactly.
  • Page 16 INSTRUCTIONS D’ALLUMAGE – VANNE GAZ MILLIVOLT POUR VOTRE SÉCURITÉ, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE AVERTISSEMENT : SI VOUS NE SUIVEZ PAS CES INSTRUCTIONS À LA LETTRE, IL POURRAIT S’EN SUIVRE UN INCENDIE OU UNE EXPLOSION CAUSANT DES DOMMAGES MATÉRIELS, DES BLESSURES CORPORELLES OU MÊME DES PERTES DE VIE. • Appelez immédiatement votre compagnie de gaz en utilisant le télé- A. Cet appareil est muni d’une veilleuse qui doit être allumée avec un phone du voisin.

  • Page 17: Replacement Parts List

    REPLACEMENT PARTS LIST Gas Controls Item # Part/Cat. No. Description Where Used 67L70 Pilot Assembly, NG/LP EBVI5 & EBVI30 67L68 Pilot Tube EBVI5 & EBVI30 67L67 Thermocouple EBVI5 & EBVI30 60J79 Thermopile (pilot generator) EBVI5 & EBVI30 10K86 Piezo Igniter EBVI5 4M89 Piezo Igniter...
  • Page 18 REPLACEMENT PARTS DIAGRAMS  1 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

  • Page 19: Troubleshooting Guide

    TROUBLESHOOTING THE MILLIVOLT GAS CONTROL SYSTEM Note: Before troubleshooting the gas control system, be sure external gas shut off valve (located at gas supply inlet) is in the “ON” position. Important: Valve system troubleshooting should only be accomplished by a qualified service technician. SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION...

  • Page 20: Product Reference Information

    6. The installation date of the appliance. We recommend that you record the following important information about If you encounter any problems or have any questions concerning the your fireplace. Please contact your Lennox dealer for any questions or installation or application of this system, please contact your dealer. concerns. For the number of your nearest Lennox dealer, please call 1-800-9-LENNOX. LENNOX HEARTH PRODUCTS REPLACEMENT PARTS 1110 West Taft Orange, CA 92865 visit us at www.Lennox.com See Pages 17 and 18 for a complete replacement parts list. Use only parts supplied from the manufacturer. Your Fireplace Insert's Model Number _ __________________________________ Your Fireplace Insert’s Serial Number ___________________________________ The Date On Which Your Fireplace Insert Was Installed _ _____________________ The Type of Gas Your Fireplace Insert Uses _______________________________ Your Dealer's Name _________________________________________________ Fuel Type (Check one) c Natural Gas c Propane Gas (LP) LENNOX reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for insert code information.

This manual is also suitable for:

Elite ebvi25Elite ebvi30

Table of Contents