This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of RISK OF ELECTRIC SHOCK, sufficient magnitude to constitute a risk of electric shock to persons. DO NOT OPEN This symbol is intended to alert the user to the presence of important operating and ATTENTION : RISQUE CHOC LELECTRIQUE-NE...
Page 3
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.
Page 4
shock, or other hazards. Upon completion of any service or repair to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products(including amplifiers) that produce heat.
Page 5
11. Introduction 1.1 Overview 1.2 Main Features 12. Safety/Precautions 2.1 Safety 2.2 Precautions 3. Check Point before Use 3.1 Accessories 14. Controls/Functions 4.1 Front Panel 4.2 Rear Panel 4.3 Remote Control unit 15. Using Remote Control unit 5.1 Batteries 5.2 Range Of Operation 16.
Page 6
This terrestrial receiver is designed for giving you the opportunity to enjoy digital broadcasting. This receiver is a technical masterpiece, assembled with the highest qualified electronic parts. Fully compliant with MPEG-2 and DVB standards User friendly operating Menu and On-Screen Graphic Menu Easy to use EPG ( Electronic Program Guide ) on screen Age protection lock function Manual PID control...
Page 7
Be sure to read the user's manual before Do not touch the power cord with wet hands starting the operation of the unit. as it may cause electric shock. Never open the cover. It is very dangerous to Place the unit in a well ventilated and no- touch the inside of the unit due to possible heat environment.
Page 8
When installing the unit Install the unit horizontally. An uneven Do not put heavy items such as a TV on the installation may cause the unit to be unit. That may cause the unit to be damaged. damaged. Do not leave the unit where the water Do not put water holding items shch as vase drops or splashs.
Page 9
Accessories of the Unit User's manual : 1 Remote control : 1 INFO AUDIO GUIDE CH.LIST AUX IN RECALL MENU EXIT TV/STB TV/RADIO Batteries (AAA type) : 2 RCA video/audio cable : 1 RF Cable(0.25M) : 1 If any accessories listed above are missing, contact the sales representative where you purchased this unit.
Page 10
11 12 5390 Power To switch the receiver in “standby” mode or in power on mode. Remote Sensor Receives the infrared signal from remote control. Channel Display(4 Digit) - When you connect the power line of the receiver, the current time is displayed. - After programming, the program number is displayed.
Page 11
Vol. To adjust the volume level or change the value of an item with preprogrammed values. The Key can be used as a backspace to cancel the numerical input. To change channel or cursor position on the application screen. Remote Control indication light Flashes orange when receiving data from remote control.
Page 12
8 11 TV ANT RF LOOP IN RS-232C S/PDIF RF LOOP OPTICAL S-VIDEO COAXIAL RF OUT UHF 21-69 9 10 12 Name Connector Function DIGITAL AUDIO Optical port Digital audio output. S-VIDEO S-Video jack S-Video output. DIGITAL AUDIO RCA cinch Digital Audio Output.
Page 13
POWER : To switch into ‘standby’ or ‘power on’ mode. MUTE : To turn the sound on/off. Numeric Keys(0-9) : To select channels and input of channel numbers or characters. INFO AUDIO INFO. : To display the information of the current channel.
Page 14
MENU : To enter/exit the main menu. Icon indicate this key in OSD menu. EXIT : To return to previous status or menu. Icon indicate this key in OSD menu. & Down : To change the value of a selected item with preprogrammed values in menu.
Page 15
: To delete a channel from the BLUE Channel List menu. To show extended program information in the EPG menu. To see Teletext Service Data. To play or pause the stored programs on HD. : To add a new channel to the WHITE Channel List menu.
Page 16
How to insert a battery Open the cover at the top of the rear side of the remote control. Insert two AAA type batteries(1.5V) to be aligned with appropriate +/- polarity. Close the cover completely. When to replace a battery If the operational range of remote control is getting smaller, it indicates batteries are almost consumed.
Page 17
The remote controller can be detected by the receiver within an angle of 30 degrees to the left or right. The transmission distance of the remote control is 7m in direct line of sight. Notes When the remote control is not operative Replace batteries with new ones and check AC power plug on the receiver.
Page 18
TV ANT RF LOOP IN RS-232C S/PDIF RF LOOP OPTICAL S-VIDEO COAXIAL RF OUT UHF 21-69 TV ANT RF LOOP IN RS-232C S/PDIF RF LOOP OPTICAL S-VIDEO COAXIAL RF OUT UHF 21-69...
Page 19
TV ANT RF LOOP IN RS-232C S/PDIF RF LOOP OPTICAL S-VIDEO COAXIAL RF OUT UHF 21-69 TV ANT RF LOOP IN RS-232C S/PDIF RF LOOP OPTICAL S-VIDEO COAXIAL RF OUT UHF 21-69...
After your receiver is powered up, proceed with installation as follows: Menu Language Setting When you plug in AC power, the following will be displayed on the front. Press POWER on remocon, the LED number will be displayed as follows; Screen...
Page 21
Press MENU key and position cursor on ‘Language' column with Select language you want with Screen Main Menu System Parameters Installation Language English Languages displayed in 'Language' column are supported by your receiver. Note :...
Page 22
Help If you want to know how to use current part in the menu, use ‘help' function. Select a content in the menu. For example, if you want to know about the installation menu, select installation. Screen Main Menu System Parameters Installation Language English...
Page 23
Tuner State You need to check signal state of your receiver. Press MENU key. Select ‘Installation’ with , and press Screen Installation Tuner State Automatic Full Scan Manual Scan Factory Set Software Download -Next, Note : Enter 4-Digit password if need arise. The default password is ‘0000’ . Select ‘Tuner State’...
Page 24
Level Indicating selected channel signal strength level. Quality Indicating signal to noise ratio. Select the channel you want with When the channel is selected, you can check the reception status of the signal. If the reception signal status is bad, adjust antenna to get the following result. Tuner Lock 1/2, 2/3, 3/4, 5/6 or 7/8...
Page 25
Screen Automatic Full Scan Scanning:2% Radio: BBC TWO BBC PARLMNT BBC ONE BBC PARLMNT BBC NEWS 24 BBC PARLMNT BBC CHOICE BBC PARLMNT BBC PARLMNT CH 7. 184.5 MHz Auto 7 MHz -Select, -Main, -Prev. When scanning is finished, you can see the following menu on the screen. Screen Automatic Full Scan Scanning:100%...
Select Channel You can change the current channel to any other channel you want. If you do not know the channel name, or you want to select a channel at random, you can navigate between channels with (CH. Up/Down) till you find the channel you want.
Page 27
Volume Control While you are watching a program, press to control volume of the current channel. Note : You can configure volume of each channel differently. Screen When necessary, press MUTE key to remove the sound of the program temporarily. Then, your receiver goes into mute condition and the volume bar will become red.
Favorite Channel You can set up favorite channel lists as you want. Note : If you press yellow key, you can set up favorite channel list without channel list menu. For example, if you want to set favorite channel lists as following. Favorite1 : BBC Two, Kika Favorite2 : ZDF Favorite3 : ABC Two, ABC One...
Page 29
Press RED. Screen TV Channel List - - - All List Favorite State CH 51. 690.5MHz BBC TWO Favorite 1 Auto BBC ONE 7 MHz Favorite 2 BBC CHOICE KiKa Favorite 3 FAV. DEL. Favorite 4 ABC TWO LOCK ABC ONE Favorite 5 MOVE MODE...
Page 30
Screen TV Channel List - - - All List CH 51. 690.5MHz BBC TWO Auto BBC ONE 7 MHz BBC CHOICE KiKa FAV. DEL. ABC TWO LOCK ABC ONE MOVE MODE ABC NEWS 24 -Page Up/Down, -Watch, -Main, -Exit, -Move Do the same for the ‘Kika' channel.
Page 31
Press RED. Screen TV Channel List FACTS Test All List Favorite State CH 45. 650.0 MHz BBC TWO Favorite 1 Auto BBC ONE 7 MHz Favorite 2 BBC CHOICE KiKa Favorite 3 FAV. DEL. Favorite 4 ABC TWO LOCK ABC ONE Favorite 5 MOVE MODE...
Page 32
Press RED. Screen TV Channel List FACTS Test All List Favorite State CH 45. 650.0 MHz BBC TWO Favorite 1 Auto BBC ONE 7 MHz Favorite 2 BBC CHOICE KiKa Favorite 3 FAV. DEL. Favorite 4 ABC TWO LOCK ABC ONE Favorite 5 MOVE MODE...
Page 33
Press WHITE. Screen TV Channel List FACTS Test All List Favorite State CH 45. 650.0 MHz BBC TWO Auto Favorite 1 BBC ONE 7 MHz BBC CHOICE Favorite 2 KiKa Favorite 3 FAV. DEL. Favorite 4 ABC TWO LOCK ABC ONE Favorite 5 MOVE MODE...
Channel List Mode Using this function, you can see variant channel lists which may enable you to edit and select channels more conveniently. Note : If you press green key, you can set up channel list mode without channel list menu. Favorite Mode If you have set up favorite channel lists as the previous section, you can use them as fol- lowing.
Page 35
Press ORANGE. Screen TV Channel List - - - All List All List Channel List Mode CH 7. 184.5 MHz ABC TWO Auto ABC ONE 7 MHz ABC NEWS 24 Favorite Favorite 1 ABC CHOICE Network Australia Darwin TWO FAV. DEL.
Page 36
Press Screen TV Channel List Favorite 1 - - - CH 7. 184.5MHz ABC TWO Auto Darwin ONE 7 MHz Seven One FAV. DEL. LOCK MOVE MODE -Page Up/Down, -Watch, -Main, -EXIT, -Move You can see only favorite1 channels are listed. With similar way, you can see favorite2 ~ favorite5 channel list.
Page 37
Alphabet Mode Using this function, you can see the channel list which have same initial. This function is useful when you search specific channel among the list of thousands channels. For example, if you want to see the channel lists which start with ‘D'. Press ORANGE in the channel list and select ‘Alphabet' with Screen TV Channel List...
Press Screen TV Channel List - - - CH 41. 620.5 MHz DWtv Auto Darwin ONE 7 MHz Darwin TWO FAV. DEL. LOCK MOVE MODE -Page Up/Down, -Watch, -Main, -EXIT, -Move You can see the channel list where all channels have initial ‘D'. Network Mode By using this function, you can see all channel list of the selected Network.
Lock Channel This menu enables you to prevent children from viewing programs unsuitable for their age. Press CH.LIST and Select the channel you want to lock with and press GREEN. Then the selected channel is locked. Screen TV Channel List FACTS Test All List CH 45.
Page 40
Screen TV Channel List FACTS Test All List All List CH 45. 650.0 MHz BBC TWO Auto BBC ONE 7 MHz BBC CHOICE KiKa FAV. DEL. ABC TWO LOCK ABC ONE ABC NEWS 24 MOVE MODE -Page Up/Down, -Watch, -Main, -EXIT, -Move Screen...
Page 41
Screen Information 376 ZDF hh:mm -- : -- ~ -- : -- If you want to cancel the channel lock, go to the channel list and select the channel and press GREEN. Channel Order Setting You can organize the number or sequence of the channels. Press CH.LIST.
Page 42
Select the channel you want to move with and press YELLOW. Screen TV Channel List - - - All List CH 61. 760.5 MHz BBC TWO Auto BBC ONE 7 MHz BBC CHOICE KiKa FAV. DEL. ABC TWO LOCK ABC ONE ABC NEWS 24 MOVE MODE...
Press YELLOW. Screen TV Channel List All List CH 61. 760.5 MHz BBC TWO Auto BBC ONE 7 MHz KiKa BBC CHOICE FAV. DEL. ABC TWO LOCK ABC ONE ABC NEWS 24 MOVE MODE -Page Up/Down, -Watch, -Main, -EXIT, -Move Press MENU, EXIT or to finish the process.
Page 44
Press BLUE. Note : If ‘password' window is risen as following picture, enter password with numeric keys (default password is' 0000'). Then you can delete the channel. If you don't want this window, change ‘Parental Control' set up in the ‘System Parameters' menu. Refer to the 'Parental control' in System parameters' in this manual for detail.
Add Channel Press CH.LIST. Press White. Screen Add Digital Channel CH. Number CH 7 CH. Name BBC ONE Video PID 0600 Audio PID 0601 PCR PID 0600 -Edit, -Prev. Move to ‘CH. Number' section (column) by pressing and change CH. Number with Move to ‘CH.
Page 46
Setting Age Restrictions This sub-menu allows you to set the age for parental locking and protect children from viewing programs unsuitable for their age. Press MENU key. Press to select ‘System Parameters' and press Screen System Parameters Parental Control System Information Local time/Timer dd/mm/yyyy hh:mm DL Saving...
Page 47
No age limit Block all Block All General Parental Guidance Recommended Mature Audience 15+ Mature Adult Audience 15+ Audience, Strong Violence 15+ Restricted 18+ Note : ‘ A ge limit’ can be applicable only for the signal which carries age limit information.
Security Check You can set SECURITY CHECK to protect your current installation from being changed (location shift, deletion, adding etc.) or modifying of installed data. Press MENU key. Press to select ‘System Parameters' and press Press to select ‘Parental Control' and press Enter 4-digit password.
System Information You can check the current information about your receiver such as receiver’s software and hardware version or manufacturing date. Press MENU key. Press to select ‘System Parameters' and press Screen System Parameters Parental Control System Information Local time/Timer dd/mm/yyyy hh:mm DL Saving A/V Mode...
Page 50
Setting Timer (Automatic power On/Off) You can pre-set the on/off time of your receiver. During your absence, you can record programs on your VCR. Press MENU key. Press to select ‘System Parameters’, and press Screen System Parameters Parental Control System Information Local time/Timer 02/07/2001 06:34 DL Saving...
Page 51
Press to select ‘Timer #(number)’ you want to set and press determine ‘CH. Type' by selecting ‘TV' or ‘RADIO' with Select 'CH. Number' with and enter channel number with numeric keys or with Select ‘Start Time’ for your receiver power-on. For example : For 1st of February in the year of 2000, 7:30 P.M., Enter in sequence...
Page 52
Setting TV Type You can set your TV display mode with this sub-menu. Press MENU key. Press to select ‘System Parameters’, and press Press to select ‘TV Type’. Press to select ‘Multi’, ‘PAL’, or ‘NTSC’. Multi When your TV is compatible with NTSC/PAL dual mode. When your TV is only for PAL reception.
Setting Screen You can select the terrestrial input signal display mode. Press MENU key. Press to select ‘System Parameters’, and press Press to select ‘Screen’. Press to select ‘P/S’ or ‘L. Box’. When you set screen display boundary from Pan/Scan data of Satellite input signal.
Page 54
After checking ‘Tuner State’, when necessary, you can edit parameters of certain channels and scan them. Press MENU key. Select ‘Installation’ with , and press Screen Installation Tuner State Automatic Full Scan Manual Scan Factory Set Software Download -Next, -Prev. Select ‘Manual Scan’...
Page 55
Move to ‘Channel’ with and select the Channel you want to edit with You can use the numeric keys to enter the channel you require. If you press , you can see cursor is created. And if you enter channel number and press , it will move to that channel.
Page 56
After scanning process, the first channel of scanned channel will be displayed. Screen Manual Scan Success Radio: FACTS HD Test.. BBC PARLMNT FACTS SD Test.. BBC PARLMNT FACTS SD Test.. BBC PARLMNT Good FACTS SD Test.. BBC PARLMNT BBC TWO BBC PARLMNT BBC ONE BBC NEWS 24...
Page 57
The status of the receiver will return to factory default parameters by using this function. Press MENU key. Select ‘Installation’ with , and press Screen Installation Tuner State Automatic Full Scan Manual Scan Factory Set Software Download -Next, Select ‘Factory Set’ with , and press Screen Installation...
Page 58
Software Download function enables user to download and update new program from air. Press MENU key. Select ‘Installation’ with , and press To start receiving the data through air, press on ‘Software Download'. It takes a few minutes to search the group of programs & downloaded channel. Move to next Menu if you succeed in searching the necessary information.
TV / STB switching Press ‘TV/STB’. The signal reception path will change to RF modulator and ‘TV/STB’ LED on front panel will be lit. The signal output through the RF modulator will be as follows : DC Power OFF ( Standby ) TV/STB LED DC Power ON RF IN signal will be out.
GUIDE(EPG:Electronic Program Guide) You can check the channel information on the channels of the transponder you are watching. Press GUIDE key, then the following menu will be displayed. Screen Program Guide 10:45 Current CNN TURK PEOPLE AND POLOTOCS Genc Tv Fashion Tv Number One Discovery Tur...
Page 61
Select Channel with Then you can see current or next program information of the selected channel. If you press GREEN, current or next program information would be converted to next or current program information respectively. Screen Program Guide 10:45 Current CNN TURK PEOPLE AND POLOTOCS Genc Tv...
Page 62
If you press YELLOW, you can see program schedule list of the selected channel. Screen Program Guide 10:46 [470] DWtv 10:30~11:00 PEOPLE AND POLITICS 28/08/2003 10:30~11:00 09:00~09:30 JOURNAL PEOPLE AND POLITICS 09:30~10:00 IM FOCUS 10:00~10:30 JOURNAL 10:30~11:00 ART & UNLIMITED 11:00~11:30 JOURNAL 11:30~12:00...
Page 63
If you press BLUE, you can see extended program information of the selected pro- gram. Screen Program Guide 10:47 [470] DWtv News, Business, Top Story, Weather 25/08/2003 10:00~10:30 JOURNAL -Current/Next, -Schedule, -Extended, -Page Up/Dn You can set up automatic power on-off (Timer) or automatic recording on the pro- gram schedule list.
Page 64
Screen Program Guide 06:47 [9] Nine Digital 08:30~09:00 THE PRICE IS PICHT Timer 25/08/2003 10:00~09:00 09:00~09:30 JOURNAL --:-- 06/08/2003 08:29 ~ 06/08/2003 09:05 --:-- --:-- Status Once --:-- HD record --:-- --:-- -Reserve, -Exit Press MENU, EXIT or to finish GUIDE menu. Screen Program Guide 06:47...
Page 65
Subtitle/Audio You can adjust the subtitle and audio condition/status of the current channel. Press ‘AUDIO’ and subtitle and audio related window will be displayed on the screen. Screen Subtitle/Audio Subtitle Track 2 of 10 [Swedish] Audio Track 1 of 8 [English] Audio Mode Stereo Dig.Output...
The contents of each parameter are as follows ; (Subtitle language #) of (all subtitle language available in this Subtitle Track program) [ Current selected subtitle language ] (Audio track #) of (all tracks available in this program ) [spoken Audio Track language in this program ] Audio Mode...
Page 67
Aux in You can set in/out mode of the two scart connectors (TV, AUX) on the rear panel. Press ‘Aux in’ key until the scart mode you want is displayed. Screen Screen...
Page 68
Screen Input terrestrial signal will be output to TV Scart and AUX (VCR) Scart. ( can connect VCR to AUX connector for recording ) Input signal from AUX scart connector will be output to TV scart. If there is no input from AUX scart, your receiver will work as if you chose STB mode. Input signal from AUX scart connector will be output to TV scart by force.
Channel / Information Brief information is displayed, such as current channel type, name, local start/end time, guide information, current time, fav/normal mode, Audio mode and Audio ID. Press INFO, then the information bar will pop-up. Screen FACTS Test 200 FACTS SD Test.. 06:32 10:15 ~ 10:21 Note : If you have no information :...
Page 70
Captions Hot-Key Captions On/Off If there is captions in stream, you can see caption data by Caption Hot-Key. Screen If there is no captions in stream, You cae see ‘None’ Title Bar. Screen None...
Page 71
Ratio Hot-Key for Aspect Ratio Change By Ratio Hot-key you can select aspect ratio. Screen 4 x 3 Letter Box Hot-Key for Timer function If you press this key, you can setting Timer function directly. Screen Timer 06/08/2003 01:53 Timer #1 CH.
Start Recording You can record the current channel by pressing RED( ) key. Direct Recording Press RED( ) key only once. Starting record current channel on the spot. Screen 00:00:13 / 00:00:17 Stereo SEVEN MORNING NEWS Note : While a program is recorded, if you press INFO or key, red R-icon is displayed information bar.
Manual Recording Press RED( ) key twice.(Double click) Program Guide menu appeared with recording dialog menu. You can edit channel name and information. Screen Program Guide 00:51 Current 7 Digital 25/0NING NEWS Name Digital 1 Information SEVEN MORNIN.. Start 00:51 Stop 02:51 00:35...
Page 74
Press key to start recording. Screen Program Guide 00:51 Current 7 Digital seven morn 25/0NING NEWS Name 7 Digital 1 Information SEVEN MORNIN.. Start 00:51 Stop 02:51 00:35 02:05 -Record, -Exit, -Edit Note : Default recording duration time is set for 2 hours. You can set recording duration 23hours 59 minutes maximally Screen Program Guide...
Reserve Recording You can reserve recording by means of a timer function. please refer to the section 7.3.5 ‘Setting Timer’. You can reserve recording by means of EPG function. please refer to the section 7.7.3 ‘GUDIE(EPG)’. Stop Recording After the time, which is either given by the EPG or set by you, the recording automatically stops.
Page 76
HD-Program Guide menu is displayed, press ORANGE(LIST) once again or EXIT key. Screen HD-Program Guide 06:49 Title Play Type Do you want to stop recording? This is BBC CHOICE 13:13 This is BBC CHOICE 14:27 This is BBC CHOICE 04:16 THE PRICE IS RIGHT Play time: Free:37.7 GB (49.4%)
Start Playing You must select a program to play stored programs. For entering HD-Program Guide menu, press ORANGE(LIST) key. Press ORANGE(LIST) key. In HD-Program Guide, select a program by pressing Screen HD-Program Guide 06:50 Title Play Type This is BBC CHOICE 13:13 This is BBC CHOICE 14:27...
Page 78
Trick Play Controls For using trick play mode, you must press or INFO key then HD-Information Bar will pop-up. Screen 2 BBC CHOICE 00:00:28 / 86:27:07 Stereo This is BBC CHOICE Trick Play Mode : Pause, Jump, Fast Forward, Fast Reverse, Resume. HD Playing HD Paused Fast Forward...
Page 79
You can delete any program in HD-Program Guide menu. Press ORANGE(LIST) key then HD-Program Guide menu will pop-up. In HD-Program Guide, select a program with Press RED( ) key to delete the program then Delete dialog menu will pop-up. Screen HD-Program Guide 06:49 Title...
Page 80
If you want to lock any program, enter the advanced menu by pressing MENU key with HD- Information Bar. After locking a program, you must enter the password for playing the program. Start playing a program. Press then HD-Information Bar will pop-up. Press MENU key, the advanced menu will pop-up.
Page 81
You can set the part you don’t want to play, such as advertise ments. The skip part consists of start and end points. In all, 10 skip points are available. Select a program with , and press to play in HD-Program Guide menu. Start playing and search the start point of skip play you want using trick play controls.
Page 82
Then a proper pair of start and end points will be displayed with yellow pointers on the Bar. Screen 5 Nine Digital 00:00:25 / 00:00:30 Stereo THE PRICE IS RIGHT Note : To try setting on improper pair will be rejected. Press RED( ) key at the position between start and end points, then the skip-point will be removed.
Page 83
You can split a program in two programs. The operation takes a few minutes to complete splitting. Select a program with , and press to play in HD-Program Guide menu. Search the split point you want using trick play controls. Press MENU key, then the advanced menu will pop-up.
Page 84
Press to start splitting or EXIT key to void. If split operation starts, the progress window will pop-up and you can see the status of process. Screen HD-Program Guide 06:49 Title Play Type Now splitting program This is BBC CHOICE 13:13 This is BBC CHOICE 14:27...
Page 85
You can use trick play controls without HD-Information Bar. Small yellow icon will be displayed for trick play controls. Additional play control is available in this mode. This function is activated at pause state using GREEN( ) / YELLOW( ). and make the sequence played step by step.
Page 86
Hot-Key for direct recording and pause function. You can immediately record the current channel. And replay the picture as you want. Press white key. Current channel recording starts with pause the picture.(Time-shift fuction starting) Screen 4 Nine Digital 00:00:00 / 00:00:12 Stereo THE PRICE IS RIGHT...
Page 87
There may be various reasons for the abnormal operation of the unit. Therefore, if the unit does not work properly, check it according to the procedures shown in the table below : Problem Possible causes Remedy LED on front panel AC Power is disconnected.
Page 88
System capabilities Fully DVB-T compliant Tuner Connector IEC 169-2, female/male Input :170MHz ~ 860MHz Frequency range Loop through out : 50MHz ~ 860MHz Channel bandwidth 7MHz Modulation COFDM Constellation QPSK, 16QAM, 64QAM Tx mode 2K, 8K, Auto Guard interval 1/4, 1/8, 1/16, 1/32, Auto Spectral inversion Auto conversion RF modulator...
Page 89
Remote control Code NEC-IR Operating condition up to 7 Meter Power supply Power consumption Max 30W Supply voltage 240V Supply frequency 47Hz 63Hz Rear Panel Video out 1 X RCA cinch connector Audio out 2 X RCA cinch 1 X RCA cinch Digital audio out 1 X optical port S-Video...
Connections For connection of the SRT 5390 there are number of alternatives depending what is your preference and the connection types on your TV. Please connect by either of the following methods A. B. C. (D. is mandatory for antenna connection) Refer to Page 8 of the Instruction Manual for the Connector Reference Numbers listed below.
CVBS (Composite Video & MPEG-2 Stereo for Audio) Connector 11 TVANT IN IEC 169-2 female Terrestrial Connector 8 VIDEO RCA cinch Composite video stream input from antenna to SRT 5390 output Connector 9 AUDIO Left (White) RCA cinch Left audio output Connector 10 AUDIO Right (Red)
Page 94
Power On Turn the SRT 5390 ON. There is an ON/OFF Switch on the rear panel of the Receiver. (Located beside the main power cord from the receiver) Now Push the On/OFF Power button on the Remote Control (Red Button)
The Correct A/V Mode Assure the correct A/V Mode has been selected in the Menu by Pushing Menu Button on the remote Control; Main Menu Banner will appear; Select System Parameters and then scroll down to A/V Mode and select the preferred AV mode: i.e. RGB or S-Video (Y/C) or CVBS (Composite) Once preferred A/V mode has been selected, Push EXIT button 11 on the remote control to return to...
Page 96
B. You can choose to connect RF from this connector to your VCR (separately purchased Lead) which will enable you to watch a normal Digital Broadcast Channel through the SRT 5300 / SRT 5390 and at the same time you can record a different broadcast channel into the VCR.
Page 97
(Requires separately purchased Scart Lead for (Using supplied RF Loop Lead) connection to VCR or DVD) With the SRT 5390 is a supplied RF Loop Lead. Essentially, there are 3 alternatives for using this connection and would mainly be used where there When used, this is connected to Connector 6 are not enough Video Connections on your TV.
Overview Selecting and Changing Checking your Aerial Channels Signal: Level & Quality There are 2 methods to select and change channels To assure that you can receive adequate picture quality for digital transmissions, it is important to check that A. Press the desired Number Button on the remote you have enough Signal Level and Quality Level control.
Setting Aspect Ratio There are 2 methods to Set and Switch between your preferred Aspect Ratio: I.e. 4:3 Letterbox / 4:3 Full Screen / 16:9 Full Screen. A. Menu Setting Press MENU button 10 Select System Parameters and press Enter button Select Aspect Ratio preferred i.e.
Parental Control Enables setting of AGE LIMIT as a protection for Children’s viewing. There are 8 categories that can be selected. No Block / Block All / Block G & Above / Block PG & Above/ Block M & Above / Block MA &...
Recording Information There are 4 methods of Recording: Manual Record – Continuous Manual Record – Time Length Input Delayed Recording Time Shift Recording Manual Record – Continuous Manual Record – Time Length Input • Push the RED Record Button ONCE and Recording will commence and continue until you •...
Recording Information Delayed Recording There are 14 Timer Entries available. • Push the GREY Timer Record button (Bottom Right) • Timer banner will be viewed listing the available 14 entries • With Time slot entry highlighted, push the ENTER button •...
Recording Information Time Shift Recording • Push the WHITE Time Shift Pause Button and • To stop the Time Shift recording mode, push the Broadcast view will be ‘Paused’ and Recording will ORANGE ‘List’ Button be actioned. • HD Program Guide Banner will be viewed with the •...
Controlling Recorded Files Playing Back Files Fast Forward & Fast Rewind In each of the 4 Recording Modes, your completed Whilst playing back a recorded file, including when in recorded files will be held within the Hard Drive File List. Time Shift mode, you can action FF &...
Page 105
Controlling Recorded Files File Search Function using White Progressive Banner bar will be viewed at the top of the banner and Total Length (Time) of this recorded Progressive Bar file will be ‘progressively’ noted on the right as well as the Current’...
Page 106
Controlling Recorded Files Play back of a previously recorded file, whilst recording. This a method that enables you to play back a previously recorded File and at the same time be recording a new program file. Can be actioned on all recording modes i.e. Manual Recording –...
Page 107
Controlling Recorded Files B. Renaming your file from A. Renaming your File in your Recorded Files the Manual Record – Time within the HD Program Length Input mode Guide Banner. In the Manual Record – Time Length Input mode, you can choose to change the file program name in the •...
Page 108
Controlling Recorded Files Skip Points Within a Recorded Program File, you can select up to . Once end Skip Point position has been selected, 10 Skip Points sections (Per File), being sections of push RED record button and a yellow icon will be your recorded program that you do not want to view viewed at that position.
Page 109
Controlling Recorded Files Deleting the Skip Points You can delete your Skip Points from your files by actioning as follows: • Push the ORANGE ‘List’ Button • HD Program Guide banner will be viewed. • Scroll to your selected recorded file •...
Controlling Recorded Files Split Take For previously recorded files, this enables you to split • Now Splitting Program banner will be viewed identifying the percentage of the file split. your file into 2 sections. This creates 2 separate files on you Hard Drive. •...
Page 111
IMPORTANT: At any time the SRT 5390 is switched to Standby mode, this setting will be cancelled.