Table of Contents
Advertisement
2WAY REMOTE STARTER/ALARM
Menu 3- Starter Settings
Setting 2 With 14pin Connector- Gas/Diesel Mode (Auxiliary Connector Pin 12)
1) (-) Input
2) Time Delay
*3) Gas/ (+) Input
Press & Release the Program Button 2 Times (Setting 2) Confirmed with 2 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
Note: Setting 2 will vary depending on the board layout 11 or 14 pin connectors.
Setting 3 Rearm Output (Auxiliary Connector Pin 1)
1) Type 1
2) Type 2
*3) Factory Re-arm 3 Flashes/chirps
Press & Release the Program Button 3 Times (Setting 3) Confirmed with 3 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
Setting 4 Run Time
1) 4 Minutes
2) 45 Minutes
*3) 15 Minutes
Press & Release the Program Button 4 Times (Setting 4) Confirmed with 4 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
Setting 5 Maximum Crank Time
1) 10 Seconds
2) 3 Seconds
*3) 5 Seconds
Press & Release the Program Button 5 Times (Setting 5) Confirmed with 5 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
Setting 6 Anti-Grind/Starter Kill (Auxiliary Connector Pin 4)
1) Active
1 Flash/chirp
2) Passive
2 Flashes/chirps
*3) Anti-grind
3 Flashes/chirps
Press & Release the Program Button 6 Times (Setting 6) Confirmed with 6 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
Setting 7 Safety Start
1) Safety On
1 Flash/chirp
*2) Safety Off
2 Flashes/chirps
Press & Release the Program Button 7 Times (Setting 7) Confirmed with 4 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
- Continued From Previous Page
1 Flash/chirp
2 Flashes/chirps
3 Flashes/chirps
1 Flash/chirp
2 Flashes/chirps
1 Flash/chirp
2 Flashes/chirps
3 Flashes/chirps
1 Flash/chirp
2 Flashes/chirps
3 Flashes/chirps
(-) when locked and during remote start (Anti-Grind).
(-) when locked /30 seconds after ignition is Off or unlock is pressed
Output during remote start only. (Anti-grind/ Bypass module)
Press the start button twice within 3seconds to remote start vehicle.
Press the start button once to remote start vehicle.
INSTALLATION MANUAL
(-) Glow Plug input. Waits maximum 30 seconds then starts.
Waits for approximately 15 seconds then remote starts.
Waits 2 seconds to start if no diesel input is detected.
Pulse after start and with lock. (Provides Lock Pulse)
Pulse after start only. (Provides Lock Pulse)
Pulse with lock and after starter shutdown.
Runs for approximately 4 minutes when activated.
Runs for approximately 45 minutes when activated.
Runs for approximately 15 minutes when activated.
10 sec max time that the starter will stay engaged.
3 sec max time that the starter will stay engaged.
5 sec max time that the starter will stay engaged.
Page 19
*(Default Settings)
Advertisement
Table of Contents
