Page 1 Hong Kong Model Tourist Model Photo : DCR-PC10E D200 MECHANISM : RMT-808 DCR-PC10/PC10E NTSC model: DCR-PC10 For MECHANISM ADJUSTMENTS, refer to the PAL model: DCR-PC10E “DV MECHANICAL ADJUSTMENT MANUAL 3 3 3 3 3 D200 MECHANISM ” (9-973-981-11), “DV MECHANICAL ADJUSTMENT MANUAL 1 1 1 1 1 D MECHANISM ”...
Page 2 MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Page 3: Table Of Contents
TABLE OF CONTENTS SERVICE NOTE DISASSEMBLY CABINET (L) ASSEMBLY REMOVAL WHEN THE 2-1. CASSETTE (L) ASSEMBLY ········································· 2-1 CASSETTE HOLDER STOPS HALFWAY DURING 2-2. CONTROL SWITCH BLOCK (FK-4850) (1) ················ 2-2 LOADING OR UNLOADING ·········································· 6 2-3. CONTROL SWITCH BLOCK (FK-4850) (2) ················ 2-2 HANDLING THE VC, MR BOARDS ······························...
Page 4 • MR-39 (SERVO), 1-4-3. VCO Adjustment (PD-97 Board) ·································· 5-28 FP-242/FP-584 (TAPE SENSOR) 1-4-4. BRIGHT Adjustment (PD-97 Board) ···························· 5-29 SCHEMATIC DIAGRAM ···························· 4-71 1-4-5. CONTRAST Adjustment (PD-97 Board) ······················ 5-29 • FP-242/FP-584 (TAPE SENSORS) 1-4-6. White Balance Adjustment ············································ 5-30 PRINTED WIRING BOARDS ·····················...
Page 5 3-7-3. EXT MIC Input Gain and L/R Balance Check ············· 5-63 3-7-4. EXT MIC Input Separation Check ································ 5-63 3-7-5. EXT MIC Input Distortion Factor Check ······················ 5-63 3-7-6. EXT MIC Input Noise Level Check ······························ 5-64 3-8. ARRANGEMENT DIAGRAM FOR ADJUSTMENT PARTS ················································...
Page 6: Service Note
SERVICE NOTE CABINET (L) ASSEMBLY REMOVAL WHEN THE CASSETTE HOLDER STOPS HALFWAY DURING LOADING OR UNLOADING (Do not remove cabinet (L) assembly in the state that the cassette holder stops halfway.) Note 1: Unloading operation in the state that the tape is in the set causes tape damage. So do not perform the unloading operation. Note 2: Do not perform the following operation in the state that the unregulated power supply is connected.
Page 7: Self-Diagnosis Function
SELF-DIAGNOSIS FUNCTION 1. Self-diagnosis Function 2. Self-diagnosis display When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the counter of the function starts working, and displays on the LCD window what to LCD window shows a 4-digit display consisting of an alphabet and do.
Page 8: Self-Diagnosis Code Table
4. Self-diagnosis Code Table Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. Non-standard battery is used. Use the info LITHIUM battery. LOAD direction.
Page 37: Cassette (L) Assembly
DCR-PC10/PC10E SECTION 2 DISASSEMBLY NOTE : Follow the disassembly procedure in the numerical order given. 2-1. CASSETTE (L) ASSEMBLY 1 Two screws (K2 2 Accessory shoe 3 Accessory plate (2) !º 4 Screw (M1.7 2.5) Open the cabinet (L) assembly halfway.
Page 38: Control Switch Block (Fk-4850) (1)
2-2. CONTROL SWITCH BLOCK (FK-4850) (1) 1 Three screws (M1.7 2.5) 6 Screw (M1.7 2.5) 2 Focus/zoom section of control switch block 7 G lock frame (FK-4850) 4 Door open/close detect switch section of control switch block (FK-4850) 6 Screw 8 Two screws (M1.7 2.5)
Page 39 2-4. NOTES ON REPLACING CONTROL SWITCH BLOCK (FK-4850) There are two types of the control switch block (FK-4850), parts code suffix -11 and -12 (The supplied part for service is the suffix - 12 part only). When replacing it -11 to -12, also it is necessary to replace the grip arm assembly suffix -1 to -2 and screws suffix -11 to -31.
Page 40: Mechanism Deck Block
2-5. MECHANISM DECK BLOCK 2-6. LENS DEVICE (LSV-590A), EVF BLOCK ASSEMBLY 7 Lens device 4 Mechanism deck block 1 Screw 6 Screw (LSV-590A) 1 Two step screws (M2) (M1.7 2.5) (M1.7 2.5) 1 Two step screws 2 DD-103 board (M2) CN3900 2 EVF section 4 Remote control...
Page 41: Board, Nd5500, Lcd901
2-8. DD-103 BOARD 2 Battery terminal board 1 Screw (M1.7 3 Two screws (M1.7 DD-103 board 4 Three screws Cabinet (bottom) assembly 2-9. PD-97 BOARD, ND5500, LCD901 8 Connector !¡ Two screws (M1.7 (From VC-199 board CN1001) 2.5) 7 Connector (From VC-199 board CN1002) 9 LCD901 flexible board !º...
Page 42: Service Position-1
2-10.SERVICE POSITION-1 (MAINLY FOR VIDEO/AUDIO SYSTEM CHECKS OR ADJUSTMENTS) 1 Remove each board in the disassembly procedure. Note: Do not apply excessive force to the flexible portion of DD- 2 Connect the specified jigs as shown in the figure. 103 board because of its shortness. (Some connectors can be connected reversely by its shape.
Page 43: Service Position-2
2-11.SERVICE POSITION-2 (MAINLY FOR CAMERA SYSTEM CHECKS OR ADJUSTMENTS) 1 Remove each board in the disassembly procedure. Note: Do not apply excessive force to the flexible portion of DD- 2 Connect the specified jigs as shown in the figure. 103 board because of its shortness. (Some connectors can be connected reversely by its shape.
Page 44 2-12.CIRCUIT BOARDS LOCATION PD-97 LCD RGB DRIVER, TIMING GENERATOR, LCD BACKLIGHT CD-175 (CCD IMAGER) MR-39 (REC/PB AMP, SERVO) DD-103 (POWER SUPPLY, I/O) VC-199 CAMERA, LENS DRIVE, I/O, BLOCKING, ECC, TBC, CHCD, AUDIO, DV I/O, IR TRANSMITTER, RGB DECODER, MODE CONTROL VF-117 (EVF) CC-100 (TRANSLATION)
Page 45: Block Diagrams
DCR-PC10/PC10E SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM...
Page 46: Power Supply Block Diagram
DCR-PC10/PC10E 3-2. POWER SUPPLY BLOCK DIAGRAM 3-10E...
Page 47: Printed Wiring Boards And Schematic Diagrams
DCR-PC10/PC10E SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM FRAME SCHEMATIC DIAGRAM...
Page 48 DCR-PC10/PC10E 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS CD-175 (CCD IMAGER) PRINTED WIRING BOARD There are few cases that the part printed on this diagram isn’t mounted in this model. — Ref. No.: CD-175 board; 1,000 series — THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS...
Page 49 DCR-PC10/PC10E CD-175 (CCD IMAGER) SCHEMATIC DIAGRAM VC-199 BOARD CD-175 BOARD — Ref. No.: CD-175 board; 1,000 series — (CAMERA REC) C208 C-17 C1005 A-22 C2112 E-19 C4750 C4852 FB200 C-17 IC4716 Q4701 R410 B-12 R1132 R2307 C-23 R2388 A-10 R4765...
Page 50 DCR-PC10/PC10E There are few cases that the part printed on this diagram isn’t mounted in this model. • See page 4-11for VC-199 BOARD printed wiring board. VC-199 (MAIN) PRINTED WIRING BOARD — Ref. No.: VC-199 board; 20,000 series — • Chip parts.
Page 51: Camera) Schematic Diagram
DCR-PC10/PC10E VC-199 (CAMERA) SCHEMATIC DIAGRAM — Ref. No.: VC-199 board; 20,000 series — VC-199 BOARD (1/12) (CAMERA REC) IC216 @§,@¶ IC207 1 0.9Vp-p 4Vp-p 26MHz IC216 2 - !¡ IC200 @™ 3Vp-p 3.4Vp-p 36MHz 40nsec IC211 %§ (CL215) IC200 @•...
Page 52: Lens Drive
DCR-PC10/PC10E DCR-PC10/PC10E VC-199 (LENS DRIVE) SCHEMATIC DIAGRAM • See page 4-12 for VC-199 BOARD printed wiring board. — Ref. No.: VC-199 board; 20,000 series — VC-199 BOARD (2/12) (CAMERA REC) IC404 8 2.8Vp-p 13.5MHz LENS DRIVE 4-21 4-22 VC-199 (2/12)
Page 53: I/O) Schematic Diagram
DCR-PC10/PC10E VC-199 (I/O) SCHEMATIC DIAGRAM • See page 4-12 for VC-199 BOARD printed wiring board. — Ref. No.: VC-199 board; 20,000 series — VC-199 BOARD (3/12) !º !™ IC1102 !ª (C1132) IC1103 8 CAMERA CAMERA REC REC/PB 1.2Vp-p 3Vp-p 6.75MHz !º...
Page 54: Blocking) Schematic Diagram
DCR-PC10/PC10E VC-199 (BLOCKING) SCHEMATIC DIAGRAM • See page 4-12 for VC-199 BOARD printed wiring board. — Ref. No.: VC-199 board; 20,000 series — BLOCKING 4-26 4-27 4-28 VC-199 (4/12)
Page 55: Ecc, Tbc, Chcd) Schematic Diagram
DCR-PC10/PC10E VC-199 (ECC, TBC, CHCD) SCHEMATIC DIAGRAM • See page 4-12 for VC-199 BOARD printed wiring board. — Ref. No.: VC-199 board; 20,000 series — ECC, TBC, CHCD 4-29 4-30 4-31 VC-199 (5/12)
Page 56: Audio Signal Process
DCR-PC10/PC10E VC-199 (AUDIO SIGNAL PROCESS) SCHEMATIC DIAGRAM • See page 4-12 for VC-199 BOARD printed wiring board. — Ref. No.: VC-199 board; 20,000 series — VC-199 BOARD (6/12) (CAMERA REC/PB) !∞ IC1900 2,3 (R1901) 3.3Vp-p 13.5MHz !§ IC1900 !™ (C1908) NTSC : 3.1Vp-p...
Page 57: Dv I/O) Schematic Diagram
DCR-PC10/PC10E VC-199 (DV I/O) SCHEMATIC DIAGRAM • See page 4-12 for VC-199 BOARD printed wiring board. — Ref. No.: VC-199 board; 20,000 series — VC-199 BOARD (7/12) (CAMERA REC/PB) @º IC3500 7 6MHz 2.1Vp-p @¡ IC3502 #• 0.72Vp-p 24.575MHz DV I/O...
Page 58: Ir Transmitter
DCR-PC10/PC10E VC-199 (IR TRANSMITTER) SCHEMATIC DIAGRAM • See page 4-12 for VC-199 BOARD printed wiring board. — Ref. No.: VC-199 board; 20,000 series — VC-199 BOARD (8/12) (CAMERA REC/PB) @™ IC8401 7 REC/PB, IR ON 0.6Vp-p 3.58MHz @£ IC8401 @™...
Page 59: Schematic Diagram
DCR-PC10/PC10E DCR-PC10/PC10E VC-199 (RGB DECODER) SCHEMATIC DIAGRAM • See page 4-12 for VC-199 BOARD printed wiring board. — Ref. No.: VC-199 board; 20,000 series — VC-199 BOARD (9/12) @§ Q1000 B CAMERA REC 1.1Vp-p @¶ Q1001 B CAMERA REC 0.8Vp-p @•...
Page 60: Schematic Diagram
DCR-PC10/PC10E VC-199 (MODE CONTROL), FK-4850, ME-4850 (FUNCTION SWITCH BLOCK) SCHEMATIC DIAGRAM • See page 4-12 for VC-199 BOARD printed wiring board. — Ref. No.: VC-199 board; 20,000 series — VC-199 BOARD (10/12) @ª IC2302 $º 20MHz 3.2Vp-p #º IC2302 %£...
Page 61: Schematic Diagram
DCR-PC10/PC10E DCR-PC10/PC10E VC-199 (AUDIO CONTROL) SCHEMATIC DIAGRAM • See page 4-12 for VC-199 BOARD printed wiring board. — Ref. No.: VC-199 board; 20,000 series — VC-199 BOARD (11/12) #§ IC2100 $º (X2100) 2.8Vp-p 20MHz AUDIO CONTROL 4-49 4-50 4-51 VC-199 (11/12)
Page 62: Audio) Schematic Diagram
DCR-PC10/PC10E VC-199 (AUDIO) SCHEMATIC DIAGRAM • See page 4-12 for VC-199 BOARDprinted wiring board. — Ref. No.: VC-199 board; 20,000 series — VC-199 BOARD (12/12) #¡ IC4707 !• CAMERA REC/PB 2.8Vp-p 0.5 sec #™ IC4711 @¢ (R4809) CAMERA REC/PB 24.5MHz 2.6Vp-p...
Page 63: Rec/Pb Amp, Servo
DCR-PC10/PC10E MR-39 (REC/PB AMP, SERVO) PRINTED WIRING BOARD -11 • See page 4-60 for the printed wiring board part number suffix -12. — Ref. No.: MR-39 board; 10,000 series — • See page 4-63 for MR-39 BOARD schematic diagram. MR-39 BOARD...
Page 64: Printed Wiring Board -12
DCR-PC10/PC10E MR-39 (REC/PB AMP, SERVO) PRINTED WIRING BOARD -12 • See page 4-57 for the printed wiring board part number suffix -11. There are few cases that the part printed on this diagram isn’t mounted in this model. — Ref. No.: MR-39 board; 10,000 series —...
Page 65: Rec/Pb Amp (1))
DCR-PC10/PC10E CC-100 (TRANSLATION), MR-39 (REC/PB AMP (1)) SCHEMATIC DIAGRAMS CC-100 (TRANSLATION) PRINTED WIRING BOARD — Ref. No.: CC-100 board; 20,000 series, MR-39 board; 10,000 series — — Ref. No.: CC-100 board; 20,000 series — • Chip parts. Transistor Diode 1 2 3...
Page 66: Rec/Pb Amp (2)) Schematic Diagram
DCR-PC10/PC10E MR-39 (REC/PB AMP (2)) SCHEMATIC DIAGRAM • See page 4-57 or 4-60 for MR-39 BOARD printed wiring board. — Ref. No.: MR-39 board; 10,000 series — MR-39 BOARD (2/3) IC2701 2 - 8 PB IC2703 @¶ CAMERA REC 3.3Vp-p 3.4Vp-p...
Page 67: Servo), Fp-242/Fp-584 (Tape Sensor) Schematic Diagram
DCR-PC10/PC10E MR-39 (SERVO), FP-242/FP-584 (TAPE SENSOR) SCHEMATIC DIAGRAM • See page 4-62 for MR-39 BOARD printed wiring board. FP-242 and FP-584 (TAPE SENSORS) PRINTED WIRING BOARDS — Ref. No.: MR-39 board; 10,000 series, FP-242 and FP-586 boards; 1,000 series —...
Page 68 DCR-PC10/PC10E DCR-PC10/PC10E PD-97 (LCD DRIVER) PRINTED WIRING BOARD There are few cases that the part printed on this diagram isn’t mounted in this model. — Ref. No.: PD-97 board; 30,000 series — PD-97 BOARD C5501 C6014 Q5513 R5637 C5502 C6015...
Page 69: Lcd Rgb Driver
DCR-PC10/PC10E PD-97 (LCD RGB DRIVER) SCHEMATIC DIAGRAM — Ref. No.: PD-97 board; 30,000 series — PD-97 BOARD (1/3) (CAMERA REC/PB) IC5600 $¡ 1.1Vp-p IC5600 $º 0.8Vp-p IC5600 #ª 0.8Vp-p IC5600 !∞ 8Vp-p IC5600 !¡ 8Vp-p IC5600 9 8Vp-p LCD RGB DRIVER...
Page 70: Timing Generator
DCR-PC10/PC10E PD-97 (TIMING GENERATOR) SCHEMATIC DIAGRAM • See page 4-77 for PD-97 BOARD printed wiring board. — Ref. No.: PD-97 board; 30,000 series — PD-97 BOARD (2/3) (CAMERA REC/PB) IC5801 #∞ 2.8Vp-p 16.36MHz TIMING GENERATOR 4-84 4-85 4-86 PD-97 (2/3)
Page 71: Lcd, Power Supply For Lcd Back Light) Schematic Diagram
DCR-PC10/PC10E PD-97 (LCD, POWER SUPPLY FOR LCD BACK LIGHT) SCHEMATIC DIAGRAM • See page 4-77 for PD-97 BOARD printed wiring board. —Ref. No.: PD-97 board; 30,000 series — PD-97 BOARD (3/3) (CAMERA REC/PB) IC6000 1 NTSC : 6.4Vp-p NTSC : 394kHz PAL : 6.1Vp-p...
Page 72: Evf) Printed Wiring Board
DCR-PC10/PC10E VF-117 (EVF) PRINTED WIRING BOARD There are few cases that the part printed on this diagram isn’t mounted in this model. — Ref. No.: VF-117 board; 30,000 series — VF-117 BOARD C4400 D4400 R4422 C4401 D4500 R4423 C4402 D4501...
Page 73: Evf, Power Supply For Evf Back Light) Schematic Diagram
DCR-PC10/PC10E VF-117 (EVF, POWER SUPPLY FOR EVF BACK LIGHT) SCHEMATIC DIAGRAM — Ref. No.: VF-117 board; 30,000 series — EVF, POWER SUPPLY FOR EVF BACK LIGHT 4-93 4-94 4-95 VF-117 (1/2)
Page 74: Evf Rgb Driver
DCR-PC10/PC10E VF-117 (EVF RGB DRIVER) SCHEMATIC DIAGRAM • See page 4-90 for VF-117 BOARD printed wiring board. — Ref. No.: VF-117 board; 30,000 series — VF-117 BOARD (CAMERA REC/PB) IC4502 6 7.4Vp-p IC4502 8 7.4Vp-p IC4502 !º 6.7Vp-p IC4502 @∞...
Page 75: Power Supply
DCR-PC10/PC10E DD-103 (POWER SUPPLY) SCHEMATIC DIAGRAM • See page 4-105 for DD-103 BOARD printed wiring board . — Ref. No.: DD-103 board; 30,000 series — DD-103 BOARD IC3900 4 REC/PB 1.2Vp-p 440kHz IC3900 ^¢ REC/PB 1.2Vp-p 440kHz POWER SUPPLY 4-99...
Page 76: I/O) Schematic Diagram
DCR-PC10/PC10E DD-103 (I/O) SCHEMATIC DIAGRAM — Ref. No.: DD-103 board; 30,000 series — 4-102 4-103 4-104 DD-103 (2/2)
Page 77: Power Supply, I/O
DCR-PC10/PC10E DD-103 (POWER SUPPLY, I/O) PRINTED WIRING DIAGRAM There are few cases that the part printed on this diagram isn’t mounted in this model. — Ref. No.: DD-103 board; 30,000 series — DD-103 BOARD C3700 C3939 IC3902 G-10 Q3911 G-10...
Page 78: Adjustments
DCR-PC10/PC10E SECTION 5 ADJUSTMENTS 5-1. CAMERA SECTION ADJUSTMENT When performing adjustments, refer to the layout diagrams for adjustment related parts beginning from page 5-32. NTSC model : DCR-PC10 PAL model : DCR-PC10E 1-1. PREPARATIONS BEFORE ADJUSTMENT 1-1-1. List of Service Tools •...
Page 79 CN6200 Fig. 5-1-2...
Page 80: Preparations
1-1-2. Preparations Note 1: For details of how to remove the cabinet and boards, refer Pattern box to “2. Removal”. Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. (Except for the GUM PLL adjustment and the original oscillation adjustment) 1.5m Connect the equipment for adjustments according to Fig.
Page 81: Precautions
1-1-4. Precautions 1. Setting the Switches Unless otherwise specified, set the switches as follows and perform adjustments without loading the cassette. 4. Focus Switch (FK-4850 block) ........Manual 1. Camera/VTR (or Player) Power Switch 5. White balance Switch (Menu Screen) ....... Auto (FK-4850 block) ............
Page 82: Camera System Adjustments
1-2. CAMERA SYSTEM ADJUSTMENTS 1-2-1. Adjustment Points When Major Parts Have Been Replaced When the CCD imager or lens block is replaced, adjust the items Note: Check that the following adjustment has been completed indicated by ® in the following table. before performing “Camera Check Adjustments”.
Page 83: Modification Of Page F Data
1-2-3. Modification of Page F data If the F page data has been initialized, change the data as shown in Address Data Address Data the following table by manual input. Fixed Note 1: The fixed values in the table are not shown because they are different in destination.
Page 84: Pll Adjustment (Vc-199 Board)[Procedure-2]
1-2-5. PLL Adjustment (VC-199 Board)[Procedure-2] Subject Arbitrary Measurement Point R244 (CL207), GND (CL211) Measuring Instrument Digital voltmeter Adjustment Page Adjustment Address Specification 1.6 ± 0.1V Adjustment procedure: Order Page Address Data Procedure Set the data. (Preparation) Change the data of page: F, address: 4D, and set the DC voltage to the specified value. Press the PAUSE button.
Page 85: Hall Adjustment
1-2-7. HALL Adjustment Purpose: Variation of the HALL element outputs is removed by adjusting amplifier gain and offset. The HALL elements detect the lens iris position. Adjustment error: Oscillation of lens iris, or incorrect white balance indoor and outdoor. Subject Not required Measurement Point DDS display of EVF or LCD, or...
Page 86 Order Page Address Data Procedure Convert the value W to a decimal value to obtain the value W Calculate the value X ' from the following equation (decimal calculation). C' = W '–B' ..........equation 4 ' = (115–B' ) '–48) + 48 (C'–21) ....
Page 87: Flange Back Adjustment (1)
1-2-8. Flange Back Adjustment (1) Purpose: Automatic flange back adjustment of inner focus lens. Adjustment error: Loss of focus when switched between auto focus and manual focus. Chart for flange back adjustment Subject (Placed 2000 mm in front of the lens with illumination of 300 ±...
Page 88: Flange Back Adjustment (2)
1-2-9. Flange Back Adjustment (2) Perform this adjustment after performing “Flange Back Adjustment (1)”. Subject Subject more than 500 m away (In case of a subject less than 500 m away, that should be subjects with clear contrast such as most distant buildings, etc.) Adjustment Page Adjustment Address...
Page 89: Flange Back Check
1-2-10. Flange Back Check Siemens star (Placed 2000 mm in front of the lens Subject with illumination of about 200 lux.) Measurement Point Confirm focus on monitor TV Measuring Instrument Specification Value Picture must have good focus at both TELE and WIDE ends. Note 1: Set the STEADY SHOT switch (MENU display) to OFF and the D ZOOM (MENU display) to OFF.
Page 90: Picture Frame Setting
1-2-11. Picture Frame Setting Subject Color bar chart standard picture frame (1.5 m from the front of the lens) Measurement Point VIDEO output terminal (Terminated in 75 ) Measuring Instrument Oscilloscope and monitor TV Specification Value A=B, C=D, t=0 ± 0.1msec Note: Set the STEADY SHOT switch (MENU display) to OFF and the D ZOOM (MENU display) to OFF.
Page 91: Color Reproduction Adjustment
1-2-12. Color Reproduction Adjustment Purpose: Adjust the three primary color matrix coefficients for correct color reproduction. Adjustment error: Poor color reproduction. Subject Color bar chart standard picture frame Measurement Point VIDEO output terminal (Terminated in 75 ) Measuring Instrument Vectorscope Adjustment Page Adjustment Address 2E, 30, 8F, 90...
Page 92: Color Reproduction Check
1-2-13. Color Reproduction Check Purpose: Adjustment error: Poor color reproduction. Subject Color bar chart standard picture frame Measurement Point VIDEO output terminal (Terminated in 75 ) Measuring Instrument Vectorscope Specification Value Each spot must be located within the specified color reproduction zone on a vectorscope display.
Page 93: Iris In/Out Adjustment
1-2-14. IRIS IN/OUT Adjustment Purpose: Measure the light level and write into EEPROM for indoor/outdoor identification in auto white balance. Adjustment error: Incorrect white balance. Subject Clear chart (Color bar standard picture frame) Measurement Point DDS display on the EVF or monitor Measuring Instrument TV, or the page A data display on the adjustment remote commander.
Page 94: Max Gain Adjustment
1-2-15. MAX GAIN Adjustment Purpose: Sets the minimum illumination level. Adjustment error: Normal video level cannot be obtained at low illumination (dark). Subject Clear chart (Color bar standard picture frame) Measurement Point DDS display of EVF or LCD, or Measuring Instrument page: A display data of adjustment remote commander Adjustment Page...
Page 95: Auto White Balance Reference Data Input
1-2-16. Auto White Balance Reference Data Input Purpose: Adjust the reference white balance at 3200K, and calibrate the camera from white balance variations. Adjustment error: The pre-set white balance will become poor. Subject Clear chart (Color bar standard picture frame) Adjustment Page Adjustment Address 20 to 23...
Page 96: Auto White Balance Adjustment
1-2-17. Auto White Balance Adjustment Purpose: Adjust the outdoor auto white balance output data for the correct value. Adjustment error: Poor white balance at outdoor. Subject Clear chart (Color bar standard picture frame) Filter Color temperature correction filter C14 Measurement Point DDS display on the EVF or monitor Measuring Instrument TV, or the page A data display on the...
Page 97: White Balance Check
1-2-18. White Balance Check Subject White pattern standard picture frame Filter Color temperature correction filter C14 ND filter 1.0 and 0.3 Measurement Point VIDEO output terminal (Terminated in 75 ) Measuring Instrument Vectorscope Specification Value Fig. 5-1-13. A ~ C Check procedure: Order Page...
Page 98: Velocity Sensor Sensitivity Adjustment
1-2-19. Velocity Sensor Sensitivity Adjustment The “Velocity Sensor Sensitivity Adjustment” is necessary only Note 1: Record the sensitivity data which is indicated on the when the gyro sensor is replaced. If microprocessors or circuit board replacement gyro sensor before installing it. Record not is not replaced, this adjustment is not necessary.
Page 99: Evr Initial Data Input
1-3. COLOR ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENTS Note 1: The backlight (fluorescent tube) is driven by a high Adjusting connector: voltage AC power supply. Some measuring points for adjusting the viewfinder are concentrated Therefore, be careful not to touch the backlight holder as at CN6202 of the VC-199 board.
Page 100: Vco Adjustment (Vf-117 Board)
1-3-2. VCO Adjustment (VF-117 Board) Purpose: To make the TG frequency constant (amplitude). Adjustment error: VF picture will lose sync when error is large. Mode VTR stop Signal No signal VC-199 board CN6202 pin !§ Measurement Point (EVF CHECK1) Measuring Equipment Oscilloscope (DC range) GND level Adjustment Page...
Page 101: Contrast Adjustment (Vf-117 Board)
1-3-4. CONTRAST Adjustment (VF-117 Board) Purpose: Adjust contrast of the EVF screen. Adjustment error: The EVF picture becomes dull (white washing) or close to saturated image. Mode VTR stop Signal 30% white signal CN6202 pin !ª (EVF VG) on Measurement Point White 30% VC-199 board Level...
Page 102: Backlight Current Consumption Adjustment
1-3-5. Backlight Current Consumption Adjustment (VF-117 Board) Purpose: Set brightness of the back light (fluorescent lamp) to a constant level. Oscilloscope VC-199 board Adjustment error: The EVF screen will become too dark or too Pin !ª (EVF VG) bright. Mode VTR stop + (IN) CN6202...
Page 103: White Balance Adjustment
1-3-6. White Balance Adjustment Purpose: Calibrate the white balance. Adjustment error: The color reproduction of the EVF screen becomes poor. Mode VTR stop Signal 30% white signal Measurement Point Check white balance on the EVF Measuring Equipment screen. Adjustment Page Adjustment Address 70, 71 Specification...
Page 104: Lcd System Adjustments
1-4. LCD SYSTEM ADJUSTMENTS Preparation: Note 1: The backlight (fluorescent lamp) is driven by high voltage AC power supply. Therefore, be careful not to touch the back light holder with hand or you will receive an electric shock. @™ CLVG CLVG Note 2: When replacing the LCD unit, be careful not to damage the LCD unit with static electricity.
Page 105: Adjustment (Pd-97 Board)
1-4-2. 15.5 V Adjustment (PD-97 Board) Purpose: Adjust the power voltage driven LCD correctly. Subject Anything IC6001 pin 2 (CL6004) Measurement Point Measuring Equipment Digital voltmeter Adjusting Element RV6000 Specification Value 15.50 ± 0.05 V Note 1: PD-97 board CN5601 a) Confirm 8.4 ±...
Page 106: Bright Adjustment (Pd-97 Board)
1-4-4. BRIGHT Adjustment (PD-97 Board) Pedestal level Purpose: Adjust brightness of LCD screen (appearance) Adjustment error: The LCD picture will be close to saturated picture (white washing) or black compression. Mode VTR stop Signal Absolutely black signal CN3701 pin @™ (CL VG) on DD-103 Measurement Point board (Note) Pedestal level...
Page 107: White Balance Adjustment
1-4-6. White Balance Adjustment Purpose: Calibrate the white balance. Adjustment error: The color reproduction of the LCD screen becomes poor. Mode VTR stop Signal 50% white signal Measurement Point Check white balance on the LCD Measuring Equipment screen. Adjustment Page Adjustment Address C2, C3 Specification...
Page 108: Adjustment Parts
1-5. ARRANGEMENT DIAGRAM FOR ADJUSTMENT PARTS VC-199 board (SIDE A) PD-97 board (SIDE A) R224 IC216 CL6004 IC6001 IC5801 CN5801 IC1900 RV6000 CN5601 CN5602 Note: CN5801, CN5601 and CL6004 are mounted to the SIDE B. VC-199 board (SIDE B) DD-103 board (SIDE A) S2300 CL207 CL200...
Page 109: Mechanism Section Adjustments
5-2. MECHANISM SECTION ADJUSTMENTS Mechanism Section Adjustments For details of mechanism section adjustments, checks, and replacement of mechanism parts, refer to the separate volume “DV MECHANICAL ADJUSTMENT MANUAL 3 D200 Mechanism ”. 2-1. OPERATING WITHOUT CASSETTE 2-2. TAPE PATH ADJUSTMENT 1.
Page 110: Video Section Adjustments
5-3. VIDEO SECTION ADJUSTMENTS When performing adjustments, refer to the layout diagrams for adjustment related parts beginning from page 5-65. NTSC model : DCR-PC10 PAL model : DCR-PC10E 3-1. PREPARATIONS BEFORE ADJUSTMENT The following adjustment instruments are used for adjusting the video section.
Page 111: Precautions In Adjustment
3-1-3. Precautions in Adjustment The adjustments of this unit are performed in the VTR mode If the DD-103 board is disconnected from the VC-199 board, or camera mode. the lithium 3V power supply will also be disconnected and all To set to the VTR mode, set the power switch to “VTR” (or data set by the user such as date, time, menu, etc.
Page 112: Connection Of Equipment
3-1-5. Connection of Equipment Connect the measuring instruments as shown in Fig. 5-3-3. TV monitor I/O baord-1 jig VIDEO (J-6082-372-C) Adjusting remote AUDIO L (White) commander Main unit AUDIO R (Red) AUDIO VIDEO OUT/ 26-pin HEADPHONES jack MULTI connector LANC terminal Fig.
Page 113: Power Supply System Adjustments
3-2. POWER SUPPLY SYSTEM ADJUSTMENTS 1. Power Supply Voltage Check (DD-103 Board) Mode Camera recording Subject Arbitrary Measuring Instrument Digital voltmeter 3.1V check Pins @¶, @• of CN3700 Measurement Point Specified Value 3.18 ± 0.05 Vdc 2.8V check Pins #§, #¶ of CN3700 Measurement Point Specified Value 2.86 ±...
Page 114: System Controller System
3-3. SYSTEM CONTROLLER SYSTEM ADJUSTMENTS 3-3-1. Initializing the Page D Data Note: If the page D data is initialized, the following adjustments must be performed again. “LCD System Adjustments”, “Color Electronic Viewfinder System Adjustments”, “Battery Down Adjustment”, and “Base Band Block Adjustment” and “Clock Adjustment” of the “Video System Adjustment”.
Page 115: Initializing The Page C Data
3-3-3. Initializing the Page C Data Note 1: If the page C data is initialized, the following adjustments must be performed again. All RF block adjustments of “Video System Adjustments” and “Servo System Adjustments”. Note 2: Recording the data of page: C by taking note, recommended before initializing the page: C.
Page 116: Battery Down Adjustment
3-3-5. Battery Down Adjustment This unit Purpose: Set the battery end voltage. Adjustment Error: If the voltage is incorrect, the remainder of the 26-pin MULTI battery will be shorter. The image at the battery connector I/O board-1 jig end will also lose sync. (J-6082-372-C) Mode Camera record...
Page 117: Servo System Adjustments
3-4. SERVO SYSTEM ADJUSTMENTS 1. T Reel FG Duty Adjustment and CSerr Adjustment (MR-39 Board) Measurement Point Adjustment remote commander Measuring Instrument display data Adjustment Page Adjustment Address 59, 6F Specified Value CSerr Adjustment: The data of page: 3, address: 03 is “00”.
Page 118: Switching Position Adjustment (Mr-39 Board)
2. Switching Position Adjustment (MR-39 Board) Mode Playback Signal SW/OL reference tape Measurement Point Display data of page: 3, address: 03 of Measuring Instrument the adjustment remote commander. Adjustment Page Adjustment Address 4C, 4D, 4E, 4F Specified Value Adjustment procedure: Order Page Address...
Page 119: Video System Adjustments
3-5. VIDEO SYSTEM ADJUSTMENTS 3-5-1. RF Block Adjustment (MR-39 Board) 1. Record Current Adjustment/ Frequency Response Check Mode VTR stop Measurement Point For ODD channel adjustment : CH-1 : CN2708 pin 5 (CL2719) CH-2 : CN2708 pin 6 (CL2718) For EVEN channel adjustment : CH-1 : CN2708 pin 3 (CL2721) CH-2 : CN2708 pin 2 (CL2722) Measuring Instrument...
Page 120: Pll Fo Adjustment (Mr-39 Board)
2. PLL fo Adjustment (MR-39 Board) Mode VTR stop Measurement Point The displayed data of address : 04 on Measuring Instrument page : 3 Adjustment Page Adjustment Address 3D, 3C Specification Value The displayed data is in the range from FD to FF, or in the range from 00 to 03.
Page 121: Clk Delay Adjustment (Mr-39 Board)
3. CLK DELAY Adjustment (MR-39 Board) Mode Camera record/playback (LP mode) Subject Any Subject Signal Playback signal of a pre-recorded tape CH-1 : CN6202 pin !™ (C1ERP) Measurement Point CH-2 : CN6202 pin 5 (JSWP J) Measuring Instrument Oscilloscope Triggered from : CH-2 Adjustment Page [Actual waveform] Adjustment Address...
Page 122: Agc Center Level Adjustment (Vc-199 Board)
4. AGC Center Level Adjustment (VC-199 Board) Mode Camera record/playback (LP mode) Subject Any Subject Signal Playback signal of a pre-recorded tape CH-1 : CN6202 pin !™ (C1ERP) Measurement Point CH-2 : CN6202 pin 5 (JSWP J) [Actual waveform] Measuring Instrument Oscilloscope Triggered from : CH-2 6.67msec...
Page 123: Pll Capture Range Adjustment (Vc-199 Board)
5. PLL Capture Range Adjustment (VC-199 Board) 6.67msec Mode Camera record/playback (LP mode) Subject Any Subject (CN6202 !™ ) Signal Playback signal of a pre-recorded tape CH-1 : CN6202 pin !™ (C1ERP) Measurement Point CH-2 : CN6202 pin 5 (JSWP J) (CN6202 5 ) Measuring Instrument Oscilloscope...
Page 124: Aeq Adjustment (Vc-199 Board)
6. AEQ Adjustment (VC-199 Board) Mode Camera record/playback (LP mode) Subject Any Subject CN6202 pin 2 (RF MONITOR) Measurement Point Measuring Instrument Oscilloscope Adjustment Page Note: Connect the 75 resistor (1-247-804-11) between pins 1 Adjustment Address 40, 41, 42, 43, 5A and 2 of CN6202.
Page 125: Base Band Block Adjustment
3-5-2. Base Band Block Adjustment 1. Composite Output Y Level Adjustment (VC-199 Board) Purpose: Set the composite signal output level. Adjustment Error: The picture will be brighter or darker on monitor. Mode CAMERA standby Subject Internal test pattern (White 70%) Measurement Point VIDEO terminal (75 terminated) Measuring Instrument...
Page 126: S-Y Output Level Adjustment (Vc-199 Board)
3. S-Y Output Level Adjustment (VC-199 Board) Purpose: Set the Y signal output level. Adjustment Error: The picture will be brighter or darker on monitor. Mode CAMERA standby Signal Internal test pattern (White 70%) Measurement Point Y signal terminal of S VIDEO terminal (75 terminated) Measuring Instrument Oscilloscope...
Page 127: Clock Adjustment
3-5-3. Clock Adjustment 1. IC1900 27MHz XTAL fo adjustment (VC-199 Board) Set the sub-carrier frequency of the video output signal in VTR mode. Mode VTR stop Signal No signal R1901 (Pin 2 of IC1900) Measurement Point Measuring Instrument Frequency counter Adjustment Page Adjustment Address Specified Value...
Page 128: Bist Check
3-5-4. BIST Check 4-1. Playback System Check 1) Set the POWER switch to VTR (or PLAYER) position. 2) Connect the adjustment remote commander and set the HOLD switch to HOLD (SERVICE) position. 1. IC1701 (D1) playback system check Mode VTR playback Signal BIST signal (Alignment tape XH5-6: NTSC)
Page 129: Ic1901(A1) Playback System Check
2. IC1901(A1) playback system check Mode VTR playback Signal BIST signal (Alignment tape XH5-6: NTSC) (Alignment tape XH5-6P: PAL) Measurement Point Adjustment remote commander Measuring Instrument Adjustment Page Adjustment Address 14, 15 Specified Value NTSC model 7B (Data of page: 4, address: 15) B5 (Data of page: 4, address: 14) PAL model CC (Data of page: 4, address: 15)
Page 130: Recording System Check
4-2. Recording System Check Note: Perform “Playback System Check” before this check. (Playback the BIST check tape.) Mode VTR playback, CAMERA REC Signal BIST signal (Alignment tape XH5-6: NTSC) (Alignment tape XH5-6P: PAL) Measurement Point Adjusting remote commander Measuring Instrument Adjustment Page 3, 4 Adjustment Address...
Page 131 Check procedure: Order Page Address Data Procedure When the IC1701 (D1) IC3501 (INDI) playback system is normal, following data will be displayed in page: 4, address: 16 and 17. Address NTSC model PAL model When the IC1901 (A1) IC1701 (D1) playback system is normal, following data will be displayed in page: 4, address: 18 and 19.
Page 132: Ir Transmitter Adjustments
3-6. IR TRANSMITTER ADJUSTMENTS 3-6-1. Preparations Switch setting: LASER LINK ..........ON (Red LED is lit) 1. Equipment Connection Infra red receiver jig (J-6082-383-A) Frequency counter TP607 (CN003 Pin 5 ) This set (IR) Oscilloscope VIDEO 26 PIN MULTI Connector I/O board-1 jig AUDIO (J-6082-372-C)
Page 133: Ir Video Deviation Adjustment
3-6-3. IR Video Deviation Adjustment Purpose: Adjusts deviation when modulating the video signal. Adjustment Error: Too bright or too dark overall picture. Over modulation picture. (If deviation is too wide, or too narrow.) Mode CAM-STANDBY Signal Internal test pattern (White 75%) Measurement Point •...
Page 134: Audio System Adjustments
3-7. AUDIO SYSTEM ADJUSTMENTS 3-7-1. Preparations Switch Settings: Volume (ME-4850)9th position decreased from MAX (8th position increased from MIN) Connection of Audio System Measuring Devices: Connect the audio system measuring devices as shown in Fig. 5-3-17. Signal Input (External Microphone Input Mode) I/O board-1 jig This unit (J-6082-372-C)
Page 135: Playback Level Check
3-7-2. Playback Level Check 3-7-4. EXT MIC Input Separation Check Purpose: Check the playback level at each fs of 32kHz, Mode Camera mode record 48kHz and 44.1kHz. Check also the de- Signal 1kHz – 44 dBs signal : MIC (I/O emphasis characteristics at 44.1kHz.
Page 136: Ext Mic Input Noise Level Check
3-7-6. EXT MIC Input Noise Level Check Mode Camera mode record Signal No input signal : Connect the left and right channel of MIC (I/O board-1 jig) with GND. Measurement Point AUDIO VIDEO OUT/ HEADPHONES jack, left and right channels Measuring Instrument Audio level meter Specification Value...
Page 137: Adjustment Parts
3-8. ARRANGEMENT DIAGRAM FOR ADJUSTMENT PARTS VC-199 board (SIDE A) PD-97 board (SIDE A) R224 IC216 CL6004 IC6001 IC5801 CN5801 IC1900 RV6000 CN5601 CN5602 Note: CN5801, CN5601 and CL6004 are mounted to the SIDE B. VC-199 board (SIDE B) DD-103 board (SIDE A) MR-33 board (SIDE A) S2300 CL207...
Page 138: Service Mode
5-4. SERVICE MODE 4-1. ADJUSTMENT REMOTE COMMANDER (RM- Display on the Bit values 95 UPGRADED) bit3 bit2 bit1 bit0 adjustment remote bit7 bit6 bit5 bit4 To perform adjustment, the adjustment data stored in the non-volatile commander memory must be rewritten using the adjustment remote commander (RM-95 upgraded).
Page 139: Precautions When Using The Adjustment
[Sequence of Service Modes Using the Adjustment Remote Commander] START Normal mode Set the NORM - ADJ (HOLD) Enters the service mode switch ADJ (ON) Press the EDIT SEARCH Page changed Refer to the memory map +/– button Press the FF/REW button Address changed Press the PLAY/ Data changed...
Page 140 Reference: Conversion between the hexadecimal number and decimal number. In some adjustment items, data appears in hexadecimal numbers on the DDS display or on the adjustment remote commander. Maintenance engineers are expected to convert the displayed hexadecimal numbers to the corresponding decimal numbers using the following conversion table.
Page 141: Service Mode
4-2. SERVICE MODE 4-2-1. Setting the Test Mode Page D Address 10 Data Function Normal Forced camera power ON Forced VTR power ON Forced camera + VTR power ON • Set/release each test mode. Set page: 0, address: 01, data: 01 before setting the data of page D.
Page 142: Emergency Memory Address
4-2-3. Emergency Memory Address When there are no emergency, data 00 will be written in the above Page C Address 30 to 3B address (30 to 3B). When the first emergency occurs, the data corresponding to the emergency will be written in the first emergency Address Contents address (30 to 33).
Page 143: Emg Code (Emergency Code)
4-2-4. EMG Code (Emergency Code) The emergency codes are stored in the addresses : 30, 34 and 38 corresponding to the types of errors occurred. Types of error code are shown in the following table. Code Error Status No error (Initial state) Loading motor time-out during LOAD Loading motor time-out during UNLOAD T reel error...
Page 144: Key Input Check (A/D Port)
Position Code Contents Position at which the cassette compartment lock is released, and position at the farthest unload side EJECT mechanically at which the mechanism can move no further in the UNLOAD direction. BLANK code, at the boundary between codes. The mechanism will not stop at this code during operations.
Page 145: Page F Address List
4-2-7. Page F Address List Note 1: The initial value of the adjustment data is the data Note 2: Some fixed values in blanks in the table are not shown immediately after execution of Page F data initialization, because they are different in destination. When requiring and Page F data modification.
Page 146 No mark: Common NTSC model PAL model Adjustment Data Adjustment Data Address Function Address Function Initial Value Memo Column Initial Value Memo Column Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed...
Page 147 Adjustment Data Address Function Initial Value Memo Column Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed...
Page 148 4-2-8. Page D Address List Note 1: The initial value of the adjustment data is the data Note 2: Some fixed values in blanks in the table are not shown immediately after execution of Page D data initialization, because they are different in destination. When requiring and Page D data modification.
Page 149 Adjustment Data Adjustment Data Address Function Address Function Initial Value Memo Column Initial Value Memo Column EVF Contrast Adjustment Fixed Fixed Fixed Fixed Fixed Fixed EVF VCO Adjustment Fixed EVF Backlight Current Fixed Consumption Adjustment Fixed Fixed Fixed Fixed Fixed EVF Bright Adjustment Fixed Fixed...
Page 150 4-2-9. Page C Address List Note 1: The initial value of the adjustment data is the data Note 2: Some fixed values in blanks in the table are not shown immediately after execution of Page C data initialization, because they are different in destination. When requiring and Page C data modification.
Page 151 Adjustment Data Address Function Initial Value Memo Column Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed T Reel FG Duty Adjustment Table. 5-4-3 (3) 5-84E...
Page 152: Repair Parts List
DCR-PC10/PC10E SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS Note: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark ! or have some differences from the original one.
Page 153: Main Boards Section
6-1-2. MAIN BOARDS SECTION EVF block Lens device LSV-590A (J-N) supplied MIC1 BT3700 MDX-D200 Cabinet (R) assembly, LCD panel block section Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3947-927-1 COVER ASSY 3-978-748-01 WINDOW (I), REMOTE CONTROL 3-719-695-21 SCREW (M1.7X3.5), SPECIAL HEAD A-7073-347-A DD-103 BOARD, COMPLETE (PC10E) 3-975-921-01 SHEET, VIBRATION PROOF...
Page 154: Cabinet (R) Assembly, Lcd Panel Section
6-1-3. CABINET (R) ASSEMBLY, LCD PANEL SECTION supplied ND5500 LCD901 (including r D) supplied SP901 supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3947-787-1 HINGE BLOCK ASSY, ROTARY * 120 3-979-685-01 SHEET (2), PD INSULATING 1-452-777-21 MAGNET * 121 3-979-994-01 SHEET, INVERTOR...
Page 155 6-1-4. EVF BLOCK, ZOOM LENS SECTION SE501 SE500 IC101 not supplied M905 supplied supplied M904 LCD902 not supplied ND4600 (Including r E, F) Be sure to read “Note on the CCD Imager replacement” on page 4-8 when changing the CCD imager. Ref.
Page 156: Cassette Compartment Block Section
6-1-5. CASSETTE COMPARTMENT BLOCK SECTION FP-242 (See page 6-6) not supplied Attaching (Note) M901 Note: Once remove No. 720 CC fastener, don't use it again. Be sure to replace it with new one. (Attaching procedure is as shown above figure.) Ref.
Page 157: Ls Chassis Block Section
6-1-6. LS CHASSIS BLOCK SECTION Note 1: About FP-242 and FP-584 The FP-242 and FP-584 flexible boards are installed to a chassis with a hot press, which are included in the Ref. No. 762 LS chassis (S) block section, They are not supplied separately because the high precision for installation is needed. Note 2: Selecting the T washer Select proper parts for the Ref.
Page 158: Mechanism Chassis Block Section-1
6-1-7. MECHANISM CHASSIS BLOCK SECTION-1 Note: Be sure to remember the installed position (one of two position), direction and thickness of the Ref. No. 820 (head spacer) when the M902 (capstan motor )is removed. Refer to “3-9. Capstan motor” on page 15 in the DV MECHANICAL ADJUSTMENT MANUAL 1 (9-973-815-11) for details.
Page 159: Mechanism Chassis Block Section-2
6-1-8. MECHANISM CHASSIS BLOCK SECTION-2 supplied not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3945-640-1 PULLEY ASSY, RELAY 3-748-741-03 GEAR, NO.1 3-315-414-31 WASHER 3-748-731-02 ARM, POSITION X-3748-600-1 ARM ASSY, COMPULSION X-3945-639-1 PULLEY ASSY, CONVERSION X-3748-605-1 CAM (S) ASSY 3-748-734-01 BELT, RELAY 3-976-452-01 LEVER, EJECT...
Page 160: Electrical Parts List
CC-100 CD-175 DD-103 6-2. ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms. please include the board name. specified in the diagrams or the components METAL: metal-film resistor The components identified by mark ! or...
Page 161 DD-103 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C3920 1-107-820-11 CERAMIC CHIP 0.1uF < IC > C3921 1-164-850-11 CERAMIC CHIP 10PF 0.5PF C3922 1-164-850-11 CERAMIC CHIP 10PF 0.5PF IC3900 8-759-384-78 IC SN104241PM-TEB C3923 1-164-940-11 CERAMIC CHIP 0.0033uF 10% IC3901 8-759-510-73 IC BA10393F-E2...
Page 162 DD-103 FP-242 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q3905 8-729-037-58 TRANSISTOR UN9110J-(TX).SO R3941 1-218-989-11 METAL GLAZE 1/16W Q3906 8-729-037-61 TRANSISTOR UN9113J-(TX).SO R3942 1-218-849-11 METAL GLAZE 1.2K 0.50% 1/16W Q3907 8-729-041-24 TRANSISTOR NDS355AN R3943 1-208-713-11 METAL GLAZE 0.50% 1/16W Q3910 8-729-025-81 TRANSISTOR 2SA1729-RS-TD...
Page 163 FP-584 FP-615 MR-39 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks FP-584 FLEXIBLE BOARD C2750 1-162-974-11 CERAMIC CHIP 0.01uF C2751 1-162-974-11 CERAMIC CHIP 0.01uF ******************** (Ref.No.: 1,000 series) C2752 1-162-927-11 CERAMIC CHIP 100PF C2753 1-107-826-11 CERAMIC CHIP 0.1uF 3-976-824-01 HOLDER, FPC C2754...
Page 164 MR-39 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C3147 1-107-826-11 CERAMIC CHIP 0.1uF < IC > C3148 1-164-360-11 CERAMIC CHIP 0.1uF C3149 1-107-826-11 CERAMIC CHIP 0.1uF IC2700 8-759-426-25 IC MB88346LPFV-G-BND-ER C3150 1-164-360-11 CERAMIC CHIP 0.1uF IC2701 8-752-371-18 IC CXD2302Q-T4 C3151...
Page 165 MR-39 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < RESISTOR > R3107 1-218-953-11 METAL GLAZE 1/16W R3108 1-218-953-11 METAL GLAZE 1/16W R2701 1-218-973-11 METAL GLAZE 1/16W R3109 1-218-985-11 METAL GLAZE 470K 1/16W R2703 1-218-971-11 METAL GLAZE 1/16W R3110 1-218-977-11 METAL GLAZE...
Page 166 MR-39 PD-97 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R3174 1-218-960-11 METAL GLAZE 3.9K 1/16W C5626 1-107-686-11 TANTAL. CHIP 4.7uF R3175 1-218-960-11 METAL GLAZE 3.9K 1/16W C5800 1-164-943-11 CERAMIC CHIP 0.01uF R3176 1-208-721-11 METAL GLAZE 0.50% 1/16W C5801 1-164-940-11 CERAMIC CHIP...
Page 167 PD-97 VC-199 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < COIL > R5641 1-218-973-11 METAL GLAZE 1/16W R5800 1-218-967-11 METAL GLAZE 1/16W L5500 1-414-396-21 INDUCTOR 4.7uH R5801 1-218-973-11 METAL GLAZE 1/16W L5600 1-414-757-11 INDUCTOR 100uH R5802 1-218-957-11 METAL GLAZE 2.2K...
Page 168 VC-199 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C222 1-135-259-11 TANTAL. CHIP 10uF 6.3V C427 1-164-677-11 CERAMIC CHIP 0.033uF C223 1-107-820-11 CERAMIC CHIP 0.1uF C428 1-164-677-11 CERAMIC CHIP 0.033uF C229 1-164-943-11 CERAMIC CHIP 0.01uF C429 1-135-259-11 TANTAL.
Page 169 VC-199 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C1700 1-164-943-11 CERAMIC CHIP 0.01uF C3501 1-107-820-11 CERAMIC CHIP 0.1uF C1703 1-164-943-11 CERAMIC CHIP 0.01uF C3504 1-107-820-11 CERAMIC CHIP 0.1uF C1704 1-164-943-11 CERAMIC CHIP 0.01uF C3506 1-107-820-11 CERAMIC CHIP 0.1uF C1705 1-107-820-11 CERAMIC CHIP...
Page 170 VC-199 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C4792 1-164-874-11 CERAMIC CHIP 100PF C8409 1-135-259-11 TANTAL. CHIP 10uF 6.3V C4793 1-164-874-11 CERAMIC CHIP 100PF C8410 1-107-823-11 CERAMIC CHIP 0.47uF C4794 1-109-982-11 CERAMIC CHIP C8411 1-107-823-11 CERAMIC CHIP 0.47uF C4795 1-164-874-11 CERAMIC CHIP...
Page 171 VC-199 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks D4711 8-719-056-23 DIODE MA2S111-(K8).SO IC1701 1-801-484-11 IC TGA-uPD82014UB-501-J D4712 8-719-045-87 DIODE MA4Z082WA-(TX).SO IC1900 1-801-477-11 IC TGA-D3106HA D4713 8-719-421-67 DIODE MA132WK IC1901 1-801-478-11 IC TGA-D3107HA D4714 8-719-056-23 DIODE MA2S111-(K8).SO IC2100 1-801-933-11 IC TGA-P912032-055HA D4715...
Page 172 VC-199 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks L4703 1-414-754-11 INDUCTOR 10uH Q4723 8-729-037-72 TRANSISTOR UN9211J-(TX).SO L4705 1-414-248-11 INDUCTOR 2.2uH Q4726 8-729-015-47 TRANSISTOR 2SK1062(TE85L) L4706 1-414-756-11 INDUCTOR 47uH Q4727 8-729-037-53 TRANSISTOR 2SB1462J-QR(TX).SO L8402 1-412-948-11 INDUCTOR 5.6uH Q4728 8-729-429-50 TRANSISTOR XP4312 L8403...
Page 173 VC-199 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R412 1-218-953-11 METAL GLAZE 1/16W R1116 1-218-990-11 SHORT R413 1-218-968-11 METAL GLAZE 1/16W R1117 1-218-953-11 METAL GLAZE 1/16W R414 1-218-980-11 METAL GLAZE 180K 1/16W R1118 1-218-953-11 METAL GLAZE 1/16W R415 1-218-965-11 METAL GLAZE...
Page 174 VC-199 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R1925 1-218-953-11 METAL GLAZE 1/16W R2345 1-219-570-11 METAL GLAZE 1/16W R1926 1-218-977-11 METAL GLAZE 100K 1/16W R2346 1-218-941-11 METAL GLAZE 1/16W R1927 1-218-941-11 METAL GLAZE 1/16W R2347 1-218-941-11 METAL GLAZE 1/16W R1928...
Page 175 VC-199 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R3528 1-218-965-11 METAL GLAZE 1/16W R4799 1-218-973-11 METAL GLAZE 1/16W R3529 1-218-965-11 METAL GLAZE 1/16W R4800 1-218-974-11 METAL GLAZE 1/16W R3530 1-218-953-11 METAL GLAZE 1/16W R4801 1-218-973-11 METAL GLAZE 1/16W R3531 1-218-977-11 METAL GLAZE...
Page 176 VC-199 VF-117 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R4864 1-218-977-11 METAL GLAZE 100K 1/16W R8432 1-218-964-11 METAL GLAZE 8.2K 1/16W R4865 1-218-965-11 METAL GLAZE 1/16W R8435 1-218-955-11 METAL GLAZE 1.5K 1/16W R4867 1-218-977-11 METAL GLAZE 100K 1/16W R8438...
Page 177 VF-117 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C4514 1-135-181-21 TANTALUM CHIP 4.7uF 6.3V < RESISTOR > C4515 1-164-940-11 CERAMIC CHIP 0.0033uF 10% C4516 1-164-937-11 CERAMIC CHIP 0.001uF R4400 1-218-949-11 METAL GLAZE 1/16W C4517 1-164-874-11 CERAMIC CHIP 100PF R4401 1-218-969-11 METAL GLAZE...
Page 178 VF-117 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R4553 1-218-953-11 METAL GLAZE 1/16W ACCESSORIES & PACKING MATERIALS R4554 1-218-990-11 SHORT ******************************* R4600 1-218-971-11 METAL GLAZE 1/16W R4601 1-218-941-11 METAL GLAZE 1/16W A-7009-689-A AC POWER ADAPTOR (AC-V100) (PC10: US, Canadian) <...
Page 179 PARTS REFERENCE SHEET You can find the parts position of location of mount locations applying to VC-199 board of a set. VC-199 SIDE A DCR-PC10/PC10E IC1900 Take a copy of CAMERA COLOR REPRODUCTION FRAME and Parts referencesheets with a clear...
Page 180 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT DCR-PC10 Take a copy of CAMERA COLOR REPRODUCTION FRAME and Parts referencesheets with a clear sheet for use. DCR-PC10E — 277 —...
Page 181 DCR-PC10/PC10E Sony Corporation 97J1651-1 Printed in Japan © 1997.10 9-973-998-11 Personal A&V Products Company Published by Quality Engineering Dept. — 278 — (Osaki East)

This manual is also suitable for:

Dcr-pc10e

Sony DCR-PC10 Service Manual

Service Note

Self-Diagnosis Function

2 Disassembly

Block Diagrams

1 General

Printed Wiring Boards and Schematic Diagrams

Adjustments

Repair Parts List

Quick Links

Related Manuals for Sony DCR-PC10

Summary of Contents for Sony DCR-PC10

This manual is also suitable for:

Table of Contents