31-10702-1 06-09 JR Installation Instructions Professional Outdoor Grills and Cooktop Tables de cuisson et barbecues de plein air professionnels Instructions d’installation La section française commence à la page 23 Parrillas y estufa profesionales para el aire libre Instrucciones de instalación La sección en español empieza en la página 45...
— with your Owner’s Manual for future reference. If you have questions concerning the installation of this product, call the GE Answer Center Information Service at 800.626.2000, 8 a.m. to 10 p.m. EST, Monday through Friday, and 8 a.m. to 7 p.m. EST, Saturday.
Installation Instructions FOR OUTDOOR USE ONLY IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THIS MANUAL THOROUGHLY BEFORE INSTALLATION, USE OR SERVICING THIS EQUIPMENT. CALIFORNIA PROPOSITION 65 WARNING: The burning of gas cooking fuel generates some by-products, which are on the list of substances, which are known by the State of California to cause cancer or reproductive harm.
Make Electrical Connections ...19 ZGG420NB, 42" Built-In Natural Gas ZGG420LB, 42" Built-In LP Gas ZGG542NC, 54" Natural Gas Grill with Cart and 2 Side Burners ZGG542LC, 54" LP Gas Grill with Cart and 2 Side Burners ZGG300NC, 30" Natural Gas Grill with Cart ZGG300NB, 30"...
PRODUCT DIMENSIONS AND CLEARANCES 54" Built-In** 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 27" 42" Built-In** 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 27" 30" Built-In** 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 27"...
Page 6
PRODUCT DIMENSIONS AND CLEARANCES 54" Cart with Side Burners 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 15-1/2" (both sides) 27" 54" Cart 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 15-1/2" (both sides) 27"...
Page 7
Design Information PRODUCT DIMENSIONS AND CLEARANCES 42" Cart 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 15-1/2" (both sides) 51" 27" 41-7/8" 30" Cart 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 15-1/2" (both sides) 51"...
ADVANCE PLANNING Built-In Monogram Outdoor Grills and Cooktops are designed for easy installation into a non-combustible enclosure. The grill drops into the opening and hangs from its side flanges. • A deck is not required for support from the bottom. •...
ELECTRICAL SUPPLY REQUIREMENTS A 120-volt, 60Hz, 15-amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle at the rear and below the cutout. Electrical must be located within reach of the 6-ft.
OUTDOOR GRILL, COOKTOP AND ACCESSORY CUTOUT DIMENSIONS 28-3/4" for 30" Models Between Cutouts 40-3/4" for 42" Models 52-3/4" for 54" Models 24-1/2" Grill Cutout Access Doors 1-1/8" 36" ZX27AD Min. Min. Gas and Electrical Locations 10" Min. 3-1/2" 3-1/2" 7-3/8" 3-1/2"...
TOOLS REQUIRED Saber Saw Measuring Tape Carpenter’s Square Safety Glasses Phillips #2 Screwdriver Level Pliers Utility Knife MATERIALS REQUIRED (not provided) Pipe Joint Sealant Pipe Fittings (approved type and resistant to LP or natural gas) Use stainless steel or flexible metal gas line to reach the built-in installation location or cart model location (if natural or whole-house LP).
REMOVE PACKAGING FROM CART MODELS 1. Cut the banding. Use a box cutter or utility knife to score and cut the carton along the base (or remove the staples with a staple remover or a screwdriver). 2. Lift the carton straight up and off of the grill. 3.
REMOVE PACKAGING FROM CART MODELS (cont.) 8. Position the blade of the dolly next to the right side of the grill. Tilt the grill back and away to allow blade to slip under the wheels. NOTE: The wheels must rest on the blade of the appliance dolly.
REMOVE PACKAGING FROM BUILT-IN MODELS 1. Cut the banding. Use a box cutter or utility knife to score and cut the carton along the base (or remove the staples with a staple remover or a screwdriver). 2. Lift the carton straight up and off of the grill. 3.
Open the tank valve when ready to use the grill. Always close the tank valve when cooking is complete. LP GAS GRILL CONNECTIONS TO A GRILL OR COOKTOP LP Gas Cooktop and Grill Combination Connections Use this method to connect a single tank to both appliances.
LP GAS GRILL CONNECTIONS TO A GRILL OR COOKTOP (cont.) Single Gas Cooktop or Grill Connection 3/8” Flare Fitting 20-lb. Type 1 LP Tank Built-in models shown. For models installed on carts, open the tank storage drawer on the right side to make the tank connection.
WARNING: TEST FOR LEAKS A complete gas tightness check must be performed at the installation site. CAUTION: To prevent fire or explosion hazard, DO NOT use or permit sources of ignition in the area while performing a leak test. Perform leak test outdoors only. Never perform a leak test with fire or flame.
INSTALL BRACKET WITH TRANSFORMER (Built-In Models Only) • Mount the bracket to the back wall of the enclosure with 4 screws (not supplied). • Slide the battery compartment from the top, straight down, engaging the side slots. Bracket Side Slots INSTALL COOKTOP BRACKET WITH BATTERY COMPARTMENT •...
Page 20
Installation Instructions 24-1/8" 24-1/8" Double Access Double Access Doors Doors • Cut the opening to the dimensions shown. Reinforce the inside of the opening using at least 1" wide material surround to accept the frame-mounting screws. • Place the frame into the opening and secure with screws (provided) on all sides as shown.
Page 21
Installation Instructions 2-Drawer Storage 18-9/16" ZX18DS 17-1/4" 10-1/8" 24-1/8" 25-3/16" 18" 1-1/4" Drawer Overlap ZX18DS STORAGE DRAWER IMPORTANT: The supplied rear support bracket adjusts from 4-1/8 " to 6-7/8 " . When using the supplied bracket, cut the opening at least 4-1/8 " above the floor.
Page 22
Installation Instructions 16" 24" Spring Hinge Clips (2) ZX18TC TRASH BIN • Cut the opening to the dimensions shown. Reinforce the inside of the opening using at least 1 " wide material surround to accept the frame-mounting screws. NOTE: If you are installing another accessory into the same enclosure, measure and cut the openings to accommodate the bottom overlaps and align them evenly across the bottom.
Manuel d’utilisation pour consultation ultérieure. Pour toute question concernant l’installation de ce produit, appelez au Centre d’appels GE Answer Center au numéro 1-800-626-2000 du lundi au vendredi de 8 h 00 à 22 h 00 HNE, et le samedi de 8 h 00 à...
Instructions d’installation POUR UTILISATION EN PLEIN AIR SEULEMENT UNE INSTALLATION, UN RÉGLAGE, UNE MODIFICATION, UNE RÉPARATION OU UN ENTRETIEN INADÉQUATS PEUVENT CAUSER DES DOMMAGES MATÉRIELS OU DES BLESSURES GRAVES OU MORTELLES. VEUILLEZ LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’INSTALLER, D’UTILISER OU DE RÉPARER CE PRODUIT.
Raccordements électriques ...40 ZGG300NB, modèle encastré à gaz naturel de 76 cm (30 po) ZGG300LB, modèle encastré à GPL de 107 cm (42 po) GPL de 76 cm (30 po) ZGG542NC, barbecue à gaz naturel de 137 cm (54 po) sur chariot ZGG542LC, barbecue à...
Renseignements descriptifs DIMENSIONS DU PRODUIT ET DÉGAGEMENTS Modèle encastré de 137 cm (54 po)** Min. de 30,4 cm (12 po) par rapport aux surfaces combustibles Dégagement min. de 10,1 cm (4 po) entre le couvercle et les surfaces non combustibles 68,6 cm (27 po) Modèle encastré...
Page 27
Renseignements descriptifs DIMENSIONS DU PRODUIT ET DÉGAGEMENTS Modèle sur chariot de 137 cm (54 po) avec brûleurs latéraux Min. de 30,4 cm (12 po) par rapport aux surfaces combustibles Dégagement min. de 10,1 cm (4 po) entre le couvercle et les surfaces non combustibles 39,4 cm (15-1/2 po) (des deux côtés)
Page 28
Renseignements descriptifs DIMENSIONS DU PRODUIT ET DÉGAGEMENTS Modèle sur chariot de 107 cm (42 po) Min. de 30,4 cm (12 po) par rapport aux surfaces combustibles Dégagement min. de 10,1 cm (4 po) entre le couvercle et les surfaces non combustibles 39,4 cm (15-1/2 po) (des deux côtés) 68,6 cm (27 po)
Renseignements descriptifs ACCESSOIRES ZX18DS, deux tiroirs de rangement de 45,7 cm (18 po) DIMENSIONS DES ACCESSOIRES 57,5 cm (22-5/8 po) 46,0 cm (18-1/8 po) ZX27AD, portes d’accès de 68,5 cm (27 po) 66,0 cm (26 po) 45,7 cm (18 po) ZX18TC, poubelle de 45,7 cm (18 po) 50,8 cm...
Préparation pour l’installation PLANIFICATION PRÉLIMINAIRE Les barbecues et les tables de cuisson encastrés de plein air Monogram sont conçus pour être facilement installés dans une structure non combustible. Le barbecue s’installe dans l’ouverture et est soutenu par ses rebords latéraux. •...
Préparation pour l’installation ALIMENTATION ÉLECTRIQUE Il faut prévoir une source d’alimentation électrique de 120 volts, 60 Hz et 15 ampères. Nous recommandons un circuit individuel adéquatement mis à la terre ou un disjoncteur. Installez une prise de courant électrique à trois alvéoles, adéquatement mise à la terre, à...
Préparation pour l’installation DIMENSIONS DE L’OUVERTURE POUR LE BARBECUE, LA TABLE DE CUISSON ET LES ACCESSOIRES 73,0 cm (28-3/4 po) pour les modèles de 76 cm (30 po) Espace minimum de 30,4 cm (12 po) entre 103,5 cm (40-3/4 po) pour les les deux ouvertures modèles de 107 cm (42 po) 134,0 cm (52-3/4 po) pour les...
Préparation pour l’installation OUTILS NÉCESSAIRES Scie sauteuse Ruban à mesurer Tourne-écrou de 6,3 mm Équerre Tournevis à lame plate (lame de 2,3 mm [3/32 po]) Lunettes de sécurité Tournevis Phillips n° 2 Niveau Pinces Couteau à lame rétractable MATÉRIEL NÉCESSAIRE (NON FOURNI) Scellant pour Raccords de tuyau raccords de tuyau...
Préparation pour l’installation ENLÈVEMENT DU MATÉRIEL D’EMBALLAGE DES MODÈLES MOBILES 1. Coupez le feuillard. À l’aide d’un couteau universel ou à lame rétractable, perforez et coupez l’emballage le long de la base (ou enlevez les agrafes à l’aide d’un tire-agrafe ou d’un tournevis). 2.
Page 35
Préparation pour l’installation ENLÈVEMENT DU MATÉRIEL D’EMBALLAGE DES MODÈLES MOBILES (suite) 8. Placez la partie horizontale du diable près du côté droit du barbecue. Inclinez le barbecue vers l’avant afin de pouvoir glisser la partie inférieure du diable sous les roulettes. NOTE : Les roulettes doivent reposer sur la partie horizontale du diable pour électroménager.
Préparation pour l’installation ENLÈVEMENT DU MATÉRIEL D’EMBALLAGE DES MODÈLES ENCASTRÉS 1. Coupez le feuillard. À l’aide d’un couteau universel ou à lame rétractable, perforez et coupez l’emballage le long de la base (ou enlevez les agrafes à l’aide d’un tire-agrafe ou d’un tournevis). 2.
Instructions d’installation IMMOBILISATION DE LA BOUTEILLE DE GPL (pour les modèles encastres dans un îlot) Dans le cas des appareils de cuisson de plein air, il faut prévoir un dispositif intégré limitant le mouvement de la bouteille de GPL. Lorsque l’appareil de cuisson est intégré et alimenté par une bouteille de GPL éloignée (installation dans un îlot), il faut créer un dispositif de fixation.
Instructions d’installation RACCORDEMENT DU BARBECUE ALIMENTÉ EN GPL À UN BARBECUE OU UNE TABLE DE CUISSON (suite) Raccordement d’un barbecue ou d’une table de cuisson à gaz Raccord évasé de 9,5 mm (3/8 po) Bouteille de GPL de type 1 de 9,0 kg (20 lb) Modèle encastré...
Instructions d’installation AVERTISSEMENT : VÉRIFICATION DES FUITES Il faut effectuer un essai d’étanchéité complet du site d’installation. MISE EN GARDE : Pour éviter les risques d’incendie ou d’explosion, n’utilisez PAS des sources d’inflammation dans le secteur pendant que vous effectuez un essai d’étanchéité.
Instructions d’installation INSTALLATION DU SUPPORT ET DU TRANSFORMATEUR (modèles encastrés seulement) • Installez le support sur la paroi arrière de l’espace de rangement à l’aide de quatre vis (non fournies). • Insérez le compartiment de la pile dans la partie supérieure, puis faites-le glisser vers le bas afin qu’il soit engagé...
Page 41
Instructions d’installation 24-1/8" 61,2 cm (24-1/8 po) Portes d’accès Double Access doubles Doors • Pratiquez une ouverture de la dimension indiquée ci-dessus. Renforcez le périmètre intérieur de l’ouverture à l’aide d’un matériau mesurant au moins 2,5 cm (1 po) de largeur pour y visser les vis de fixation du cadre.
Page 42
Instructions d’installation 2 tiroirs de rangement 47,1 cm (18-9/16 po) ZX18DS 43,8 cm (17-1/4 po) 25,7 cm (10-1/8 po) 45,7 cm (18 po) Chevauchement du tiroir de 3,2 cm (1-1/4 po) 2 vis de fixation Chevauchement TIROIRS DE RANGEMENT ZX18DS IMPORTANT : La largeur du support arrière fourni peut être réglée entre 10,5 cm (4 1/8 po) et 17,5 cm (6 7/8 po).
Page 43
Instructions d’installation 40,6 cm (16 po) 60,9 cm (24 po) Charnières à ressort (2) POUBELLE ZX18TC • Pratiquez une ouverture de la dimension indiquée ci-dessus. Renforcez le périmètre intérieur de l’ouverture à l’aide d’un matériau mesurant au moins 2,5 cm (1 po) de largeur pour y visser les vis de fixation du cadre.
• No utilice tanques de LP oxidados o dañados. • Nunca sustituya gases (natural por LP o LP por natural). Estas parrillas se encuentran de GE al ® configuradas de fábrica para gas LP o natural. Solicite el modelo que se ajuste a su situación de instalación.
Instrucciones de instalación SÓLO PARA USO AL AIRE LIBRE UNA INSTALACIÓN, AJUSTE, ALTERACIÓN, SERVICIO O MANTENIMIENTO INADECUADOS PUEDEN PROVOCAR DAÑOS A LA PROPIEDAD, LESIONES O LA MUERTE. LEA ESTE MANUAL CON DETENIMIENTO ANTES DE LA INSTALACIÓN, USO O SERVICIO DE ESTE EQUIPAMIENTO. PROPOSICIÓN 65 DE CALIFORNIA ADVERTENCIA:...
ZGG300NB, 30" (76 cm) natural de 42” (107 cm) empotrado a gas natural ZGG420LB, empotrado a gas ZGG300LB, empotrado a LP de 42” (107 cm) gas LP de 30” (76 cm) ZGG542NC, parrilla a gas natural con carrito y 2 quemadores laterales de 54" (137 cm) y 2 quemadores laterales de 54"...
DIMENSIONES Y ESPACIOS DEL PRODUCTO Empotrado de 54" (137 cm)** 12" (30,4 cm) mínimo respecto de elementos combustibles 4" (10,1 cm) espacio mín. para la tapa respecto de elementos no combustibles 27" (68,6 cm) Empotrado de 42" (107 cm)** 12" (30,4 cm) mínimo respecto de elementos combustibles 4"...
Page 49
DIMENSIONES Y ESPACIOS DEL PRODUCTO Carrito de 54" (137 cm) con quemadores laterales 12" (30,4 cm) mínimo respecto de elementos combustibles 4" (10,1 cm) espacio mín. para la tapa respecto de elementos no combustibles 15-1/2" (39,4 cm) (ambos lados) 27" (68,6 cm) Carrito de 54"...
Page 50
DIMENSIONES Y ESPACIOS DEL PRODUCTO Carrito de 42" (107 cm) 12" (30,4 cm) mínimo respecto de elementos combustibles 4" (10,1 cm) espacio mín. para la tapa respecto de elementos no combustibles 15-1/2" (39,4 cm) (ambos lados) 27" (68,6 cm) Carrito de 30" (76 cm) 12"...
Información de diseño ACCESORIOS ZX27AD, puertas de acceso ZX18DS, almacenamiento ZX18TC, cubo de de 27" (68,5 cm) de 2 cajones de 18" (45,7 cm) basura de 18" (45,7 cm) DIMENSIONES DE LOS ACCESORIOS DEL PRODUCTO 22-5/8" 26" 20" (57,5 cm) (66,0 cm) (50,8 cm) 18-1/8"...
Preparación para la instalación PLANIFICACIÓN PREVIA Las parrillas y estufas para el aire libre empotradas Monogram se encuentran diseñadas para una instalación sencilla en un cerramiento no combustible. La parrilla se coloca en la abertura y cuelga de sus bridas laterales. •...
Preparación para la instalación REQUISITOS DE SUMINISTRO ELÉCTRICO Se necesita un suministro eléctrico de 120 voltios, 60 hercios y 15 amperios. Se recomienda un circuito derivado individual con adecuada conexión a tierra o un interruptor de circuitos. Instale un tomacorriente de 3 espigas con adecuada conexión a tierra en la parte trasera, debajo del recorte.
Preparación para la instalación DIMENSIONES DE LOS RECORTES PARA PARRILLA, ESTUFA Y ACCESORIOS 28-3/4" (73,0 cm) para modelos de 30" (76 cm) 40-3/4" (103,5 cm) para modelos de 42" (107 cm) 52-3/4" (134,0 cm) para modelos de 54" (137 cm) 24-1/2 "...
Preparación para la instalación HERRAMIENTAS REQUERIDAS Perforadora y brocas Sierra sable Cinta de medir Llave de cubo o llave de 1/4" Regla de carpintero Gafas de seguridad Destornillador de estrella #2 Nivel Carretilla para aparatos Alicates Cuchillo de uso general MATERIALES REQUERIDOS (no provistos) Sellador de juntas Accesorios...
Preparación para la instalación QUITE EL EMPAQUE DE LOS MODELOS CON CARRITO 1. Corte el precinto. Utilice un cortador de cajas o cuchillo de uso general para cortar el cartón a lo largo de la base (o quitar los ganchitos con una desengrampadora o un destornillador).
Page 57
Preparación para la instalación QUITE EL EMPAQUE DE LOS MODELOS CON CARRITO (cont.) 8. Coloque la hoja de la carretilla al costado del lado derecho de la parrilla. Incline la parrilla hacia atrás para permitir que la hoja se deslice bajo las ruedas.
Preparación para la instalación QUITE EL EMPAQUE DE LOS MODELOS EMPOTRADOS 1. Corte el precinto. Utilice un cortador de cajas o cuchillo de uso general para cortar el cartón a lo largo de la base (o quitar los ganchitos con una desengrampadora o un destornillador).
Instrucciones de instalación SUJECIÓN DEL TANQUE DE LP (para instalaciones empotradas en islas) Los aparatos para cocción al aire libre requieren un medio integral para limitar el movimiento del cilindro de gas LP. Para los aparatos empotrados que requieren el uso de un cilindro remoto de suministro de gas LP (aplicaciones en islas), debe crearse un dispositivo de retención.
Instrucciones de instalación CONEXIONES DE PARRILLA DE GAS LP CON UNA PARRILLA O ESTUFA (cont.) Conexión única de estufa o parrilla de gas Accesorio abierto de 3/8” (9,5 cm) Tanque de LP Tipo 1 de 20 libras Se muestran modelos empotrados. Para modelos instalados en carritos, abra el cajón de almacenamiento del tanque sobre el lado derecho para efectuar la conexión del tanque.
Instrucciones de instalación ADVERTENCIA: PRUEBA DE PÉRDIDAS Debe llevarse a cabo una prueba completa de hermeticidad en el sitio de la instalación. PRECAUCIÓN: Para evitar un riesgo de incendio o explosión, NO utilice o permita la presencia de fuentes de ignición en el área mientras realiza una prueba de pérdidas.
Instrucciones de instalación INSTALE EL SOPORTE DEL TRANSFORMADOR (Sólo modelos empotrados) • Instale el soporte en la pared trasera del cerramiento con 4 tornillos (no provistos). • Deslice el compartimento de la batería desde la parte superior, hacia abajo, enganchando las ranuras laterales.
Page 63
Instrucciones de instalación 24-1/8" 24-1/8" (61,2 cm) Puertas de Double Access acceso dobles Doors • Corte la abertura con la dimensión indicada. Refuerce la parte interna de la abertura utilizando un marco de material de por lo menos 1" (2,5 cm) de ancho para que puedan instalarse los tornillos de montaje.
Page 64
Instrucciones de instalación Almacena miento de 18-9/16" (47,1 cm) 2 cajones ZX18DS 17-1/4" (43,8 cm) 10-1/8" (25,7 cm) 18" (45,7 cm) Superposición del cajón de 1-1/4" (3,2 cm) CAJÓN DE ALMACENAMIENTO ZX18DS IMPORTANTE: El soporte trasero provisto se ajusta de 4-1/8" (10,5 cm) a 6-7/8" (17,5 cm). Cuando se utiliza el soporte provisto, corte la abertura por lo menos a 4-1/8"...
Page 65
Instrucciones de instalación 16" (40,6 cm) 24" (60,9 cm) Ganchos de bisagra a resorte (2) CUBO DE BASURA ZX18TC • Corte la abertura con la dimensión indicada. Refuerce la parte interna de la abertura utilizando un marco de material de por lo menos 1" (2,5 cm) de ancho para que puedan instalarse los tornillos de montaje del armazón.
Page 68
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram local service in your area, call ® 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. NOTE : Lorsque vous procédez à...
Need help?
Do you have a question about the Monogram ZGG300LB and is the answer not in the manual?
Questions and answers